2 * Copyright 2010-2011 Freescale Semiconductor, Inc.
3 * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
4 * Timur Tabi <timur@freescale.com>
6 * This program is free software; you can redistribute it and/or modify it
7 * under the terms of the GNU General Public License as published by the Free
8 * Software Foundation; either version 2 of the License, or (at your option)
15 #include "../board/freescale/common/ics307_clk.h"
17 /* High Level Configuration Options */
18 #define CONFIG_BOOKE /* BOOKE */
19 #define CONFIG_E500 /* BOOKE e500 family */
20 #define CONFIG_MPC85xx /* MPC8540/60/55/41/48 */
22 #define CONFIG_P1022DS
23 #define CONFIG_MP /* support multiple processors */
25 #ifndef CONFIG_SYS_TEXT_BASE
26 #define CONFIG_SYS_TEXT_BASE 0xeff80000
29 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
30 #define CONFIG_PCI /* Enable PCI/PCIE */
31 #define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
32 #define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
33 #define CONFIG_PCIE3 /* PCIE controler 3 (ULI bridge) */
34 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
35 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
36 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
38 #define CONFIG_PHYS_64BIT
39 #define CONFIG_ENABLE_36BIT_PHYS
40 #define CONFIG_ADDR_MAP
41 #define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
43 #define CONFIG_FSL_LAW /* Use common FSL init code */
45 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
46 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
47 #define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */
50 * These can be toggled for performance analysis, otherwise use default.
52 #define CONFIG_L2_CACHE
55 #define CONFIG_SYS_MEMTEST_START 0x00000000
56 #define CONFIG_SYS_MEMTEST_END 0x7fffffff
59 * Base addresses -- Note these are effective addresses where the
60 * actual resources get mapped (not physical addresses)
62 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
63 #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
64 #define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull
65 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
68 #define CONFIG_DDR_SPD
69 #define CONFIG_VERY_BIG_RAM
70 #define CONFIG_FSL_DDR3
73 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
74 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef
77 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
78 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
80 #define CONFIG_NUM_DDR_CONTROLLERS 1
81 #define CONFIG_DIMM_SLOTS_PER_CTLR 1
82 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
84 /* I2C addresses of SPD EEPROMs */
85 #define CONFIG_SYS_SPD_BUS_NUM 1
86 #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */
91 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
92 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable
93 * 0xffc0_0000 0xffc2_ffff PCI IO range 192K non-cacheable
95 * Localbus cacheable (TBD)
96 * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable
98 * Localbus non-cacheable
99 * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable
100 * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable
101 * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0
102 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
103 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
107 * Local Bus Definitions
109 #define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */
110 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
112 #define CONFIG_FLASH_BR_PRELIM \
113 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V)
114 #define CONFIG_FLASH_OR_PRELIM (OR_AM_128MB | 0xff7)
116 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
117 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
119 #define CONFIG_SYS_BR1_PRELIM \
120 (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
121 #define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM
123 #define CONFIG_SYS_FLASH_BANKS_LIST \
124 {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
125 #define CONFIG_SYS_FLASH_QUIET_TEST
126 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
128 #define CONFIG_SYS_MAX_FLASH_BANKS 2
129 #define CONFIG_SYS_MAX_FLASH_SECT 1024
131 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
133 #define CONFIG_FLASH_CFI_DRIVER
134 #define CONFIG_SYS_FLASH_CFI
135 #define CONFIG_SYS_FLASH_EMPTY_INFO
137 #define CONFIG_BOARD_EARLY_INIT_F
138 #define CONFIG_BOARD_EARLY_INIT_R
139 #define CONFIG_MISC_INIT_R
140 #define CONFIG_HWCONFIG
142 #define CONFIG_FSL_NGPIXIS
143 #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
144 #define PIXIS_BASE_PHYS 0xfffdf0000ull
146 #define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
147 #define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB | 0x6ff7)
149 #define PIXIS_LBMAP_SWITCH 7
150 #define PIXIS_LBMAP_MASK 0xE0
151 #define PIXIS_LBMAP_ALTBANK 0x20
153 #define CONFIG_SYS_INIT_RAM_LOCK
154 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
155 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
157 #define CONFIG_SYS_GBL_DATA_OFFSET \
158 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
159 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
161 #define CONFIG_SYS_MONITOR_LEN (512 * 1024)
162 #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024)
167 #define CONFIG_CONS_INDEX 1
168 #define CONFIG_SYS_NS16550
169 #define CONFIG_SYS_NS16550_SERIAL
170 #define CONFIG_SYS_NS16550_REG_SIZE 1
171 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
173 #define CONFIG_SYS_BAUDRATE_TABLE \
174 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
176 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
177 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
179 /* Use the HUSH parser */
180 #define CONFIG_SYS_HUSH_PARSER
181 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
184 #undef CONFIG_FSL_DIU_FB
186 #ifdef CONFIG_FSL_DIU_FB
187 #define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x10000)
189 #define CONFIG_CMD_BMP
190 #define CONFIG_CFB_CONSOLE
191 #define CONFIG_VGA_AS_SINGLE_DEVICE
192 #define CONFIG_VIDEO_LOGO
193 #define CONFIG_VIDEO_BMP_LOGO
194 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
196 * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
197 * disable empty flash sector detection, which is I/O-intensive.
199 #undef CONFIG_SYS_FLASH_EMPTY_INFO
203 * Pass open firmware flat tree
205 #define CONFIG_OF_LIBFDT
206 #define CONFIG_OF_BOARD_SETUP
207 #define CONFIG_OF_STDOUT_VIA_ALIAS
209 /* new uImage format support */
211 #define CONFIG_FIT_VERBOSE
214 #define CONFIG_FSL_I2C
215 #define CONFIG_HARD_I2C
216 #define CONFIG_I2C_MULTI_BUS
217 #define CONFIG_SYS_I2C_SPEED 400000
218 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
219 #define CONFIG_SYS_I2C_SLAVE 0x7F
220 #define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}}
221 #define CONFIG_SYS_I2C_OFFSET 0x3000
222 #define CONFIG_SYS_I2C2_OFFSET 0x3100
227 #define CONFIG_ID_EEPROM
228 #define CONFIG_SYS_I2C_EEPROM_NXID
229 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
230 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
231 #define CONFIG_SYS_EEPROM_BUS_NUM 1
235 * Memory space is mapped 1-1, but I/O space must start from 0.
238 /* controller 1, Slot 2, tgtid 1, Base address a000 */
239 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
240 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
241 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull
242 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
243 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
244 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
245 #define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull
246 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
248 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
249 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
250 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
251 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
252 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
253 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
254 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
255 #define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
256 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
258 /* controller 3, Slot 1, tgtid 3, Base address b000 */
259 #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
260 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
261 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull
262 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
263 #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
264 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
265 #define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull
266 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
269 #define CONFIG_NET_MULTI
270 #define CONFIG_PCI_PNP /* do pci plug-and-play */
271 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
272 #define CONFIG_E1000 /* Define e1000 pci Ethernet card */
276 #define CONFIG_LIBATA
277 #define CONFIG_FSL_SATA
279 #define CONFIG_SYS_SATA_MAX_DEVICE 2
281 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
282 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
284 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
285 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
287 #ifdef CONFIG_FSL_SATA
289 #define CONFIG_CMD_SATA
290 #define CONFIG_DOS_PARTITION
291 #define CONFIG_CMD_EXT2
296 #define CONFIG_CMD_MMC
297 #define CONFIG_FSL_ESDHC
298 #define CONFIG_GENERIC_MMC
299 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
302 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
303 #define CONFIG_CMD_EXT2
304 #define CONFIG_CMD_FAT
305 #define CONFIG_DOS_PARTITION
308 #define CONFIG_TSEC_ENET
309 #ifdef CONFIG_TSEC_ENET
311 #define CONFIG_TSECV2
312 #define CONFIG_NET_MULTI
314 #define CONFIG_MII /* MII PHY management */
315 #define CONFIG_TSEC1 1
316 #define CONFIG_TSEC1_NAME "eTSEC1"
317 #define CONFIG_TSEC2 1
318 #define CONFIG_TSEC2_NAME "eTSEC2"
320 #define TSEC1_PHY_ADDR 1
321 #define TSEC2_PHY_ADDR 2
323 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
324 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
326 #define TSEC1_PHYIDX 0
327 #define TSEC2_PHYIDX 0
329 #define CONFIG_ETHPRIME "eTSEC1"
331 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
337 #define CONFIG_ENV_IS_IN_FLASH
338 #define CONFIG_ENV_OVERWRITE
339 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
340 #define CONFIG_ENV_SIZE 0x2000
341 #define CONFIG_ENV_SECT_SIZE 0x20000
343 #define CONFIG_LOADS_ECHO
344 #define CONFIG_SYS_LOADS_BAUD_CHANGE
347 * Command line configuration.
349 #include <config_cmd_default.h>
351 #define CONFIG_CMD_ELF
352 #define CONFIG_CMD_ERRATA
353 #define CONFIG_CMD_IRQ
354 #define CONFIG_CMD_I2C
355 #define CONFIG_CMD_MII
356 #define CONFIG_CMD_PING
357 #define CONFIG_CMD_SETEXPR
358 #define CONFIG_CMD_REGINFO
361 #define CONFIG_CMD_PCI
362 #define CONFIG_CMD_NET
368 #define CONFIG_USB_EHCI
370 #ifdef CONFIG_USB_EHCI
371 #define CONFIG_CMD_USB
372 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
373 #define CONFIG_USB_EHCI_FSL
374 #define CONFIG_USB_STORAGE
375 #define CONFIG_CMD_FAT
379 * Miscellaneous configurable options
381 #define CONFIG_SYS_LONGHELP /* undef to save memory */
382 #define CONFIG_CMDLINE_EDITING /* Command-line editing */
383 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */
384 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
385 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
386 #ifdef CONFIG_CMD_KGDB
387 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
389 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
391 /* Print Buffer Size */
392 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
393 #define CONFIG_SYS_MAXARGS 16
394 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
395 #define CONFIG_SYS_HZ 1000
398 * For booting Linux, the board info and command line data
399 * have to be in the first 16 MB of memory, since this is
400 * the maximum mapped by the Linux kernel during initialization.
402 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
403 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
405 #ifdef CONFIG_CMD_KGDB
406 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
407 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
411 * Environment Configuration
414 #define CONFIG_HOSTNAME p1022ds
415 #define CONFIG_ROOTPATH /opt/nfsroot
416 #define CONFIG_BOOTFILE uImage
417 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
419 #define CONFIG_LOADADDR 1000000
421 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
422 #define CONFIG_BOOTARGS
424 #define CONFIG_BAUDRATE 115200
426 #define CONFIG_EXTRA_ENV_SETTINGS \
427 "perf_mode=stable\0" \
428 "memctl_intlv_ctl=2\0" \
430 "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
431 "tftpflash=tftpboot $loadaddr $uboot; " \
432 "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
433 "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
434 "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \
435 "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
436 "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
437 "consoledev=ttyS0\0" \
438 "ramdiskaddr=2000000\0" \
439 "ramdiskfile=uramdisk\0" \
441 "fdtfile=p1022ds.dtb\0" \
443 "diuregs=md e002c000 1d\0" \
444 "dium=mw e002c01c\0" \
445 "diuerr=md e002c014 1\0" \
446 "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 tty0\0" \
449 #define CONFIG_HDBOOT \
450 "setenv bootargs root=/dev/$bdev rw " \
451 "console=$consoledev,$baudrate $othbootargs;" \
452 "tftp $loadaddr $bootfile;" \
453 "tftp $fdtaddr $fdtfile;" \
454 "bootm $loadaddr - $fdtaddr"
456 #define CONFIG_NFSBOOTCOMMAND \
457 "setenv bootargs root=/dev/nfs rw " \
458 "nfsroot=$serverip:$rootpath " \
459 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
460 "console=$consoledev,$baudrate $othbootargs;" \
461 "tftp $loadaddr $bootfile;" \
462 "tftp $fdtaddr $fdtfile;" \
463 "bootm $loadaddr - $fdtaddr"
465 #define CONFIG_RAMBOOTCOMMAND \
466 "setenv bootargs root=/dev/ram rw " \
467 "console=$consoledev,$baudrate $othbootargs;" \
468 "tftp $ramdiskaddr $ramdiskfile;" \
469 "tftp $loadaddr $bootfile;" \
470 "tftp $fdtaddr $fdtfile;" \
471 "bootm $loadaddr $ramdiskaddr $fdtaddr"
473 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND