2 * Copyright 2013 Freescale Semiconductor, Inc.
4 * Authors: Roy Zang <tie-fei.zang@freescale.com>
5 * Chunhe Lan <Chunhe.Lan@freescale.com>
7 * SPDX-License-Identifier: GPL-2.0+
13 #ifndef CONFIG_SYS_MONITOR_BASE
14 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
17 #ifndef CONFIG_RESET_VECTOR_ADDRESS
18 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
21 /* High Level Configuration Options */
22 #define CONFIG_MP /* support multiple processors */
24 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
25 #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
26 #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
27 #define CONFIG_PCIE3 /* PCIE controller 3 (slot 3) */
28 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
29 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
30 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
33 extern unsigned long get_clock_freq(void);
36 #define CONFIG_SYS_CLK_FREQ 66666666
37 #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ
40 * These can be toggled for performance analysis, otherwise use default.
42 #define CONFIG_L2_CACHE /* toggle L2 cache */
43 #define CONFIG_BTB /* toggle branch predition */
44 #define CONFIG_HWCONFIG
46 #define CONFIG_ENABLE_36BIT_PHYS
48 #define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */
49 #define CONFIG_SYS_MEMTEST_END 0x02000000
51 /* Implement conversion of addresses in the LBC */
52 #define CONFIG_SYS_LBC_LBCR 0x00000000
53 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8
56 #define CONFIG_VERY_BIG_RAM
57 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
58 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
60 #define CONFIG_DIMM_SLOTS_PER_CTLR 1
61 #define CONFIG_CHIP_SELECTS_PER_CTRL 1
63 #define CONFIG_DDR_SPD
64 #define CONFIG_FSL_DDR_INTERACTIVE
65 #define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */
66 #define CONFIG_SYS_SPD_BUS_NUM 0
67 #define SPD_EEPROM_ADDRESS 0x50
68 #define CONFIG_SYS_DDR_RAW_TIMING
73 * 0x0000_0000 0x1fff_ffff DDR 512M cacheable
74 * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
75 * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
76 * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
77 * 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M cacheable
78 * 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
79 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable TLB0
81 * Localbus non-cacheable
83 * 0xec00_0000 0xefff_ffff NOR flash 64M non-cacheable
84 * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
88 * Local Bus Definitions
90 #define CONFIG_SYS_FLASH_BASE 0xec000000 /* start of FLASH 64M */
91 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
93 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
95 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7
97 #define CONFIG_FLASH_CFI_DRIVER
98 #define CONFIG_SYS_FLASH_CFI
99 #define CONFIG_SYS_FLASH_EMPTY_INFO
100 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
101 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
102 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
103 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
105 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
107 #define CONFIG_SYS_INIT_RAM_LOCK
108 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
109 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* Size of used area in RAM */
110 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
111 GENERATED_GBL_DATA_SIZE)
112 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
114 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) /* Reserve 512 kB for Mon */
115 #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
117 #define CONFIG_SYS_NAND_BASE 0xffa00000
118 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
120 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
121 #define CONFIG_SYS_MAX_NAND_DEVICE 1
122 #define CONFIG_NAND_FSL_ELBC
123 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
125 /* NAND flash config */
126 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
127 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
128 | BR_PS_8 /* Port Size = 8bit */ \
129 | BR_MS_FCM /* MSEL = FCM */ \
131 #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
140 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
141 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
142 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
143 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
146 #define CONFIG_CONS_INDEX 1
147 #undef CONFIG_SERIAL_SOFTWARE_FIFO
148 #define CONFIG_SYS_NS16550_SERIAL
149 #define CONFIG_SYS_NS16550_REG_SIZE 1
150 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
152 #define CONFIG_SYS_BAUDRATE_TABLE \
153 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
155 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
156 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
159 #define CONFIG_SYS_I2C
160 #define CONFIG_SYS_I2C_FSL
161 #define CONFIG_SYS_FSL_I2C_SPEED 400000
162 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
163 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
164 #define CONFIG_SYS_FSL_I2C2_SPEED 400000
165 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
166 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
171 #define CONFIG_ID_EEPROM
172 #ifdef CONFIG_ID_EEPROM
173 #define CONFIG_SYS_I2C_EEPROM_NXID
175 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
176 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
177 #define CONFIG_SYS_EEPROM_BUS_NUM 0
181 * Memory space is mapped 1-1, but I/O space must start from 0.
184 /* controller 3, Slot 1, tgtid 3, Base address b000 */
185 #define CONFIG_SYS_PCIE3_NAME "Slot 3"
186 #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
187 #define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
188 #define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
189 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
190 #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
191 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
192 #define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
193 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
195 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
196 #define CONFIG_SYS_PCIE2_NAME "Slot 2"
197 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
198 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
199 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
200 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
201 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
202 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
203 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
204 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
206 /* controller 1, Slot 2, tgtid 1, Base address a000 */
207 #define CONFIG_SYS_PCIE1_NAME "Slot 1"
208 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
209 #define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
210 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
211 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
212 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
213 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
214 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
215 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
217 #if defined(CONFIG_PCI)
218 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
219 #endif /* CONFIG_PCI */
224 #define CONFIG_ENV_OVERWRITE
226 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
227 #define CONFIG_ENV_SIZE 0x2000
228 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
230 #define CONFIG_LOADS_ECHO /* echo on for serial download */
231 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
236 #define CONFIG_HAS_FSL_DR_USB
237 #ifdef CONFIG_HAS_FSL_DR_USB
238 #ifdef CONFIG_USB_EHCI_HCD
239 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
240 #define CONFIG_USB_EHCI_FSL
245 * Miscellaneous configurable options
247 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
250 * For booting Linux, the board info and command line data
251 * have to be in the first 64 MB of memory, since this is
252 * the maximum mapped by the Linux kernel during initialization.
254 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
255 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
258 * Environment Configuration
260 #define CONFIG_BOOTFILE "uImage"
261 #define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */
263 /* default location for tftp and bootm */
264 #define CONFIG_LOADADDR 1000000
267 #define CONFIG_SYS_QMAN_MEM_BASE 0xff000000
268 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
269 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
270 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
271 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
272 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
273 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
274 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
275 CONFIG_SYS_QMAN_CENA_SIZE)
276 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
277 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
278 #define CONFIG_SYS_BMAN_MEM_BASE 0xff200000
279 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
280 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
281 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
282 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
283 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
284 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
285 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
286 CONFIG_SYS_BMAN_CENA_SIZE)
287 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
288 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
291 #define CONFIG_SYS_DPAA_FMAN
293 #ifdef CONFIG_SYS_DPAA_FMAN
294 #define CONFIG_FMAN_ENET
295 #define CONFIG_PHY_ATHEROS
298 /* Default address of microcode for the Linux Fman driver */
299 /* QE microcode/firmware address */
300 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
301 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
302 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
303 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
305 #ifdef CONFIG_FMAN_ENET
306 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1
307 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x2
309 #define CONFIG_SYS_TBIPA_VALUE 8
310 #define CONFIG_MII /* MII PHY management */
311 #define CONFIG_ETHPRIME "FM1@DTSEC1"
314 #define CONFIG_EXTRA_ENV_SETTINGS \
316 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
317 "loadaddr=1000000\0" \
318 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
319 "tftpflash=tftpboot $loadaddr $uboot; " \
320 "protect off $ubootaddr +$filesize; " \
321 "erase $ubootaddr +$filesize; " \
322 "cp.b $loadaddr $ubootaddr $filesize; " \
323 "protect on $ubootaddr +$filesize; " \
324 "cmp.b $loadaddr $ubootaddr $filesize\0" \
325 "consoledev=ttyS0\0" \
326 "ramdiskaddr=2000000\0" \
327 "ramdiskfile=rootfs.ext2.gz.uboot\0" \
328 "fdtaddr=1e00000\0" \
329 "fdtfile=p1023rdb.dtb\0" \
330 "othbootargs=ramdisk_size=600000\0" \
332 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
334 #define CONFIG_HDBOOT \
335 "setenv bootargs root=/dev/$bdev rw " \
336 "console=$consoledev,$baudrate $othbootargs;" \
337 "tftp $loadaddr $bootfile;" \
338 "tftp $fdtaddr $fdtfile;" \
339 "bootm $loadaddr - $fdtaddr"
341 #define CONFIG_NFSBOOTCOMMAND \
342 "setenv bootargs root=/dev/nfs rw " \
343 "nfsroot=$serverip:$rootpath " \
344 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
345 "console=$consoledev,$baudrate $othbootargs;" \
346 "tftp $loadaddr $bootfile;" \
347 "tftp $fdtaddr $fdtfile;" \
348 "bootm $loadaddr - $fdtaddr"
350 #define CONFIG_RAMBOOTCOMMAND \
351 "setenv bootargs root=/dev/ram rw " \
352 "console=$consoledev,$baudrate $othbootargs;" \
353 "tftp $ramdiskaddr $ramdiskfile;" \
354 "tftp $loadaddr $bootfile;" \
355 "tftp $fdtaddr $fdtfile;" \
356 "bootm $loadaddr $ramdiskaddr $fdtaddr"
358 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
360 #endif /* __CONFIG_H */