]> git.sur5r.net Git - u-boot/blob - include/configs/P2041RDB.h
configs: Finish migration of PHY_GIGE
[u-boot] / include / configs / P2041RDB.h
1 /*
2  * Copyright 2011-2012 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:     GPL-2.0+
5  */
6
7 /*
8  * P2041 RDB board configuration file
9  * Also supports P2040 RDB
10  */
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13
14 #ifdef CONFIG_RAMBOOT_PBL
15 #define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
16 #define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
17 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg
18 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg
19 #endif
20
21 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
22 /* Set 1M boot space */
23 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
24 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
25                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
26 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
27 #endif
28
29 /* High Level Configuration Options */
30 #define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
31 #define CONFIG_MP                       /* support multiple processors */
32
33 #ifndef CONFIG_SYS_TEXT_BASE
34 #define CONFIG_SYS_TEXT_BASE    0xeff40000
35 #endif
36
37 #ifndef CONFIG_RESET_VECTOR_ADDRESS
38 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
39 #endif
40
41 #define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
42 #define CONFIG_SYS_NUM_CPC              CONFIG_SYS_NUM_DDR_CTLRS
43 #define CONFIG_PCIE1                    /* PCIE controller 1 */
44 #define CONFIG_PCIE2                    /* PCIE controller 2 */
45 #define CONFIG_PCIE3                    /* PCIE controller 3 */
46 #define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
47 #define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */
48
49 #define CONFIG_SYS_SRIO
50 #define CONFIG_SRIO1                    /* SRIO port 1 */
51 #define CONFIG_SRIO2                    /* SRIO port 2 */
52 #define CONFIG_SRIO_PCIE_BOOT_MASTER
53 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
54
55 #define CONFIG_ENV_OVERWRITE
56
57 #ifndef CONFIG_MTD_NOR_FLASH
58 #else
59 #define CONFIG_FLASH_CFI_DRIVER
60 #define CONFIG_SYS_FLASH_CFI
61 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
62 #endif
63
64 #if defined(CONFIG_SPIFLASH)
65         #define CONFIG_SYS_EXTRA_ENV_RELOC
66         #define CONFIG_ENV_SPI_BUS              0
67         #define CONFIG_ENV_SPI_CS               0
68         #define CONFIG_ENV_SPI_MAX_HZ           10000000
69         #define CONFIG_ENV_SPI_MODE             0
70         #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
71         #define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
72         #define CONFIG_ENV_SECT_SIZE            0x10000
73 #elif defined(CONFIG_SDCARD)
74         #define CONFIG_SYS_EXTRA_ENV_RELOC
75         #define CONFIG_FSL_FIXED_MMC_LOCATION
76         #define CONFIG_SYS_MMC_ENV_DEV          0
77         #define CONFIG_ENV_SIZE                 0x2000
78         #define CONFIG_ENV_OFFSET               (512 * 1658)
79 #elif defined(CONFIG_NAND)
80 #define CONFIG_SYS_EXTRA_ENV_RELOC
81 #define CONFIG_ENV_SIZE                 CONFIG_SYS_NAND_BLOCK_SIZE
82 #define CONFIG_ENV_OFFSET               (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
83 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
84 #define CONFIG_ENV_ADDR         0xffe20000
85 #define CONFIG_ENV_SIZE         0x2000
86 #elif defined(CONFIG_ENV_IS_NOWHERE)
87 #define CONFIG_ENV_SIZE         0x2000
88 #else
89         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE \
90                         - CONFIG_ENV_SECT_SIZE)
91         #define CONFIG_ENV_SIZE         0x2000
92         #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
93 #endif
94
95 #ifndef __ASSEMBLY__
96 unsigned long get_board_sys_clk(unsigned long dummy);
97 #endif
98 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
99
100 /*
101  * These can be toggled for performance analysis, otherwise use default.
102  */
103 #define CONFIG_SYS_CACHE_STASHING
104 #define CONFIG_BACKSIDE_L2_CACHE
105 #define CONFIG_SYS_INIT_L2CSR0          L2CSR0_L2E
106 #define CONFIG_BTB                      /* toggle branch predition */
107
108 #define CONFIG_ENABLE_36BIT_PHYS
109
110 #ifdef CONFIG_PHYS_64BIT
111 #define CONFIG_ADDR_MAP
112 #define CONFIG_SYS_NUM_ADDR_MAP         64      /* number of TLB1 entries */
113 #endif
114
115 #define CONFIG_POST CONFIG_SYS_POST_MEMORY      /* test POST memory test */
116 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
117 #define CONFIG_SYS_MEMTEST_END          0x00400000
118 #define CONFIG_SYS_ALT_MEMTEST
119 #define CONFIG_PANIC_HANG       /* do not reset board on panic */
120
121 /*
122  *  Config the L3 Cache as L3 SRAM
123  */
124 #define CONFIG_SYS_INIT_L3_ADDR         CONFIG_RAMBOOT_TEXT_BASE
125 #ifdef CONFIG_PHYS_64BIT
126 #define CONFIG_SYS_INIT_L3_ADDR_PHYS    (0xf00000000ull | \
127                 CONFIG_RAMBOOT_TEXT_BASE)
128 #else
129 #define CONFIG_SYS_INIT_L3_ADDR_PHYS    CONFIG_SYS_INIT_L3_ADDR
130 #endif
131 #define CONFIG_SYS_L3_SIZE              (1024 << 10)
132 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
133
134 #ifdef CONFIG_PHYS_64BIT
135 #define CONFIG_SYS_DCSRBAR              0xf0000000
136 #define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull
137 #endif
138
139 /* EEPROM */
140 #define CONFIG_ID_EEPROM
141 #define CONFIG_SYS_I2C_EEPROM_NXID
142 #define CONFIG_SYS_EEPROM_BUS_NUM       0
143 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
144 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
145
146 /*
147  * DDR Setup
148  */
149 #define CONFIG_VERY_BIG_RAM
150 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
151 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
152
153 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
154 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
155
156 #define CONFIG_DDR_SPD
157
158 #define CONFIG_SYS_SPD_BUS_NUM  0
159 #define SPD_EEPROM_ADDRESS      0x52
160 #define CONFIG_SYS_SDRAM_SIZE   4096    /* for fixed parameter use */
161
162 /*
163  * Local Bus Definitions
164  */
165
166 /* Set the local bus clock 1/8 of platform clock */
167 #define CONFIG_SYS_LBC_LCRR             LCRR_CLKDIV_8
168
169 /*
170  * This board doesn't have a promjet connector.
171  * However, it uses commone corenet board LAW and TLB.
172  * It is necessary to use the same start address with proper offset.
173  */
174 #define CONFIG_SYS_FLASH_BASE           0xe0000000
175 #ifdef CONFIG_PHYS_64BIT
176 #define CONFIG_SYS_FLASH_BASE_PHYS      0xfe0000000ull
177 #else
178 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
179 #endif
180
181 #define CONFIG_SYS_FLASH_BR_PRELIM \
182                 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \
183                 BR_PS_16 | BR_V)
184 #define CONFIG_SYS_FLASH_OR_PRELIM \
185                 ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
186                  | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)
187
188 #define CONFIG_FSL_CPLD
189 #define CPLD_BASE               0xffdf0000      /* CPLD registers */
190 #ifdef CONFIG_PHYS_64BIT
191 #define CPLD_BASE_PHYS          0xfffdf0000ull
192 #else
193 #define CPLD_BASE_PHYS          CPLD_BASE
194 #endif
195
196 #define CONFIG_SYS_BR3_PRELIM   (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V)
197 #define CONFIG_SYS_OR3_PRELIM   0xffffeff7      /* 32KB but only 4k mapped */
198
199 #define PIXIS_LBMAP_SWITCH      7
200 #define PIXIS_LBMAP_MASK        0xf0
201 #define PIXIS_LBMAP_SHIFT       4
202 #define PIXIS_LBMAP_ALTBANK     0x40
203
204 #define CONFIG_SYS_FLASH_QUIET_TEST
205 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
206
207 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
208 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
209 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Erase Timeout (ms) */
210 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Write Timeout (ms) */
211
212 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
213
214 #if defined(CONFIG_RAMBOOT_PBL)
215 #define CONFIG_SYS_RAMBOOT
216 #endif
217
218 #define CONFIG_NAND_FSL_ELBC
219 /* Nand Flash */
220 #ifdef CONFIG_NAND_FSL_ELBC
221 #define CONFIG_SYS_NAND_BASE            0xffa00000
222 #ifdef CONFIG_PHYS_64BIT
223 #define CONFIG_SYS_NAND_BASE_PHYS       0xfffa00000ull
224 #else
225 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
226 #endif
227
228 #define CONFIG_SYS_NAND_BASE_LIST     {CONFIG_SYS_NAND_BASE}
229 #define CONFIG_SYS_MAX_NAND_DEVICE      1
230 #define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
231
232 /* NAND flash config */
233 #define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
234                                | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
235                                | BR_PS_8               /* Port Size = 8 bit */ \
236                                | BR_MS_FCM             /* MSEL = FCM */ \
237                                | BR_V)                 /* valid */
238 #define CONFIG_SYS_NAND_OR_PRELIM  (0xFFFC0000        /* length 256K */ \
239                                | OR_FCM_PGS            /* Large Page*/ \
240                                | OR_FCM_CSCT \
241                                | OR_FCM_CST \
242                                | OR_FCM_CHT \
243                                | OR_FCM_SCY_1 \
244                                | OR_FCM_TRLX \
245                                | OR_FCM_EHTR)
246
247 #ifdef CONFIG_NAND
248 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
249 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
250 #define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
251 #define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
252 #else
253 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
254 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
255 #define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
256 #define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
257 #endif
258 #else
259 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
260 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
261 #endif /* CONFIG_NAND_FSL_ELBC */
262
263 #define CONFIG_SYS_FLASH_EMPTY_INFO
264 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
265 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
266
267 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
268 #define CONFIG_MISC_INIT_R
269
270 #define CONFIG_HWCONFIG
271
272 /* define to use L1 as initial stack */
273 #define CONFIG_L1_INIT_RAM
274 #define CONFIG_SYS_INIT_RAM_LOCK
275 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* Initial L1 address */
276 #ifdef CONFIG_PHYS_64BIT
277 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
278 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
279 /* The assembler doesn't like typecast */
280 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
281         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
282           CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
283 #else
284 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
285 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
286 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
287 #endif
288 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
289
290 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
291                                         GENERATED_GBL_DATA_SIZE)
292 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
293
294 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
295 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)
296
297 /* Serial Port - controlled on board with jumper J8
298  * open - index 2
299  * shorted - index 1
300  */
301 #define CONFIG_CONS_INDEX       1
302 #define CONFIG_SYS_NS16550_SERIAL
303 #define CONFIG_SYS_NS16550_REG_SIZE     1
304 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
305
306 #define CONFIG_SYS_BAUDRATE_TABLE       \
307         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
308
309 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
310 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
311 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
312 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
313
314 /* I2C */
315 #define CONFIG_SYS_I2C
316 #define CONFIG_SYS_I2C_FSL
317 #define CONFIG_SYS_FSL_I2C_SPEED        400000
318 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
319 #define CONFIG_SYS_FSL_I2C_OFFSET       0x118000
320 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
321 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
322 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x118100
323
324 /*
325  * RapidIO
326  */
327 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
328 #ifdef CONFIG_PHYS_64BIT
329 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
330 #else
331 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xa0000000
332 #endif
333 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000      /* 256M */
334
335 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
336 #ifdef CONFIG_PHYS_64BIT
337 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
338 #else
339 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xb0000000
340 #endif
341 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000      /* 256M */
342
343 /*
344  * for slave u-boot IMAGE instored in master memory space,
345  * PHYS must be aligned based on the SIZE
346  */
347 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
348 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
349 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000       /* 1M */
350 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
351 /*
352  * for slave UCODE and ENV instored in master memory space,
353  * PHYS must be aligned based on the SIZE
354  */
355 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
356 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
357 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000    /* 256K */
358
359 /* slave core release by master*/
360 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
361 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
362
363 /*
364  * SRIO_PCIE_BOOT - SLAVE
365  */
366 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
367 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
368 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
369                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
370 #endif
371
372 /*
373  * eSPI - Enhanced SPI
374  */
375 #define CONFIG_SF_DEFAULT_SPEED         10000000
376 #define CONFIG_SF_DEFAULT_MODE          0
377
378 /*
379  * General PCI
380  * Memory space is mapped 1-1, but I/O space must start from 0.
381  */
382
383 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
384 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
385 #ifdef CONFIG_PHYS_64BIT
386 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
387 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
388 #else
389 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
390 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
391 #endif
392 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
393 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
394 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
395 #ifdef CONFIG_PHYS_64BIT
396 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
397 #else
398 #define CONFIG_SYS_PCIE1_IO_PHYS        0xf8000000
399 #endif
400 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
401
402 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
403 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
404 #ifdef CONFIG_PHYS_64BIT
405 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
406 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
407 #else
408 #define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
409 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
410 #endif
411 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
412 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
413 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
414 #ifdef CONFIG_PHYS_64BIT
415 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
416 #else
417 #define CONFIG_SYS_PCIE2_IO_PHYS        0xf8010000
418 #endif
419 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
420
421 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
422 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xc0000000
423 #ifdef CONFIG_PHYS_64BIT
424 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
425 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc40000000ull
426 #else
427 #define CONFIG_SYS_PCIE3_MEM_BUS        0xc0000000
428 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc0000000
429 #endif
430 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x20000000      /* 512M */
431 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
432 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
433 #ifdef CONFIG_PHYS_64BIT
434 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
435 #else
436 #define CONFIG_SYS_PCIE3_IO_PHYS        0xf8020000
437 #endif
438 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
439
440 /* Qman/Bman */
441 #define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
442 #define CONFIG_SYS_BMAN_NUM_PORTALS     10
443 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
444 #ifdef CONFIG_PHYS_64BIT
445 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
446 #else
447 #define CONFIG_SYS_BMAN_MEM_PHYS        CONFIG_SYS_BMAN_MEM_BASE
448 #endif
449 #define CONFIG_SYS_BMAN_MEM_SIZE        0x00200000
450 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
451 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
452 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
453 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
454 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
455                                         CONFIG_SYS_BMAN_CENA_SIZE)
456 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
457 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
458 #define CONFIG_SYS_QMAN_NUM_PORTALS     10
459 #define CONFIG_SYS_QMAN_MEM_BASE        0xf4200000
460 #ifdef CONFIG_PHYS_64BIT
461 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff4200000ull
462 #else
463 #define CONFIG_SYS_QMAN_MEM_PHYS        CONFIG_SYS_QMAN_MEM_BASE
464 #endif
465 #define CONFIG_SYS_QMAN_MEM_SIZE        0x00200000
466 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
467 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
468 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
469 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
470 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
471                                         CONFIG_SYS_QMAN_CENA_SIZE)
472 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
473 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
474
475 #define CONFIG_SYS_DPAA_FMAN
476 #define CONFIG_SYS_DPAA_PME
477 /* Default address of microcode for the Linux Fman driver */
478 #if defined(CONFIG_SPIFLASH)
479 /*
480  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
481  * env, so we got 0x110000.
482  */
483 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
484 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000
485 #elif defined(CONFIG_SDCARD)
486 /*
487  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
488  * about 825KB (1650 blocks), Env is stored after the image, and the env size is
489  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
490  */
491 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
492 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
493 #elif defined(CONFIG_NAND)
494 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
495 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
496 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
497 /*
498  * Slave has no ucode locally, it can fetch this from remote. When implementing
499  * in two corenet boards, slave's ucode could be stored in master's memory
500  * space, the address can be mapped from slave TLB->slave LAW->
501  * slave SRIO or PCIE outbound window->master inbound window->
502  * master LAW->the ucode address in master's memory space.
503  */
504 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
505 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
506 #else
507 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
508 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
509 #endif
510 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
511 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
512
513 #ifdef CONFIG_SYS_DPAA_FMAN
514 #define CONFIG_FMAN_ENET
515 #define CONFIG_PHYLIB_10G
516 #define CONFIG_PHY_VITESSE
517 #define CONFIG_PHY_TERANETICS
518 #endif
519
520 #ifdef CONFIG_PCI
521 #define CONFIG_PCI_INDIRECT_BRIDGE
522
523 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
524 #endif  /* CONFIG_PCI */
525
526 /* SATA */
527 #define CONFIG_FSL_SATA_V2
528
529 #ifdef CONFIG_FSL_SATA_V2
530 #define CONFIG_FSL_SATA
531 #define CONFIG_LIBATA
532
533 #define CONFIG_SYS_SATA_MAX_DEVICE      2
534 #define CONFIG_SATA1
535 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
536 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
537 #define CONFIG_SATA2
538 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
539 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
540
541 #define CONFIG_LBA48
542 #endif
543
544 #ifdef CONFIG_FMAN_ENET
545 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR  0x2
546 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR  0x3
547 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR  0x4
548 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR  0x1
549 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR  0x0
550
551 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
552 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
553 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
554 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f
555
556 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR  0
557
558 #define CONFIG_SYS_TBIPA_VALUE  8
559 #define CONFIG_MII              /* MII PHY management */
560 #define CONFIG_ETHPRIME         "FM1@DTSEC1"
561 #endif
562
563 /*
564  * Environment
565  */
566 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
567 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
568
569 /*
570  * Command line configuration.
571  */
572
573 #ifdef CONFIG_PCI
574 #define CONFIG_CMD_PCI
575 #endif
576
577 /*
578 * USB
579 */
580 #define CONFIG_HAS_FSL_DR_USB
581 #define CONFIG_HAS_FSL_MPH_USB
582
583 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
584 #define CONFIG_USB_EHCI_FSL
585 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
586 #endif
587
588 #ifdef CONFIG_MMC
589 #define CONFIG_FSL_ESDHC
590 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
591 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
592 #endif
593
594 /*
595  * Miscellaneous configurable options
596  */
597 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
598 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
599 #define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
600 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
601 #ifdef CONFIG_CMD_KGDB
602 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
603 #else
604 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
605 #endif
606 /* Print Buffer Size */
607 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
608                                 sizeof(CONFIG_SYS_PROMPT)+16)
609 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
610 /* Boot Argument Buffer Size */
611 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
612
613 /*
614  * For booting Linux, the board info and command line data
615  * have to be in the first 64 MB of memory, since this is
616  * the maximum mapped by the Linux kernel during initialization.
617  */
618 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux */
619 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
620
621 #ifdef CONFIG_CMD_KGDB
622 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
623 #endif
624
625 /*
626  * Environment Configuration
627  */
628 #define CONFIG_ROOTPATH         "/opt/nfsroot"
629 #define CONFIG_BOOTFILE         "uImage"
630 #define CONFIG_UBOOTPATH        u-boot.bin
631
632 /* default location for tftp and bootm */
633 #define CONFIG_LOADADDR         1000000
634
635 #define __USB_PHY_TYPE  utmi
636
637 #define CONFIG_EXTRA_ENV_SETTINGS                               \
638         "hwconfig=fsl_ddr:ctlr_intlv=cacheline,"                \
639         "bank_intlv=cs0_cs1\0"                                  \
640         "netdev=eth0\0"                                         \
641         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
642         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"             \
643         "tftpflash=tftpboot $loadaddr $uboot && "               \
644         "protect off $ubootaddr +$filesize && "                 \
645         "erase $ubootaddr +$filesize && "                       \
646         "cp.b $loadaddr $ubootaddr $filesize && "               \
647         "protect on $ubootaddr +$filesize && "                  \
648         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
649         "consoledev=ttyS0\0"                                    \
650         "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0"                \
651         "usb_dr_mode=host\0"                                    \
652         "ramdiskaddr=2000000\0"                                 \
653         "ramdiskfile=p2041rdb/ramdisk.uboot\0"                  \
654         "fdtaddr=1e00000\0"                                     \
655         "fdtfile=p2041rdb/p2041rdb.dtb\0"                       \
656         "bdev=sda3\0"
657
658 #define CONFIG_HDBOOT                                   \
659         "setenv bootargs root=/dev/$bdev rw "           \
660         "console=$consoledev,$baudrate $othbootargs;"   \
661         "tftp $loadaddr $bootfile;"                     \
662         "tftp $fdtaddr $fdtfile;"                       \
663         "bootm $loadaddr - $fdtaddr"
664
665 #define CONFIG_NFSBOOTCOMMAND                   \
666         "setenv bootargs root=/dev/nfs rw "     \
667         "nfsroot=$serverip:$rootpath "          \
668         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
669         "console=$consoledev,$baudrate $othbootargs;"   \
670         "tftp $loadaddr $bootfile;"             \
671         "tftp $fdtaddr $fdtfile;"               \
672         "bootm $loadaddr - $fdtaddr"
673
674 #define CONFIG_RAMBOOTCOMMAND                           \
675         "setenv bootargs root=/dev/ram rw "             \
676         "console=$consoledev,$baudrate $othbootargs;"   \
677         "tftp $ramdiskaddr $ramdiskfile;"               \
678         "tftp $loadaddr $bootfile;"                     \
679         "tftp $fdtaddr $fdtfile;"                       \
680         "bootm $loadaddr $ramdiskaddr $fdtaddr"
681
682 #define CONFIG_BOOTCOMMAND              CONFIG_HDBOOT
683
684 #include <asm/fsl_secure_boot.h>
685
686 #endif  /* __CONFIG_H */