2 * Copyright 2011-2012 Freescale Semiconductor, Inc.
4 * SPDX-License-Identifier: GPL-2.0+
8 * P2041 RDB board configuration file
9 * Also supports P2040 RDB
14 #ifdef CONFIG_RAMBOOT_PBL
15 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
16 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
17 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg
18 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg
21 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
22 /* Set 1M boot space */
23 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
24 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
25 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
26 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
29 /* High Level Configuration Options */
30 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
31 #define CONFIG_MP /* support multiple processors */
33 #ifndef CONFIG_SYS_TEXT_BASE
34 #define CONFIG_SYS_TEXT_BASE 0xeff40000
37 #ifndef CONFIG_RESET_VECTOR_ADDRESS
38 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
41 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
42 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
43 #define CONFIG_PCIE1 /* PCIE controller 1 */
44 #define CONFIG_PCIE2 /* PCIE controller 2 */
45 #define CONFIG_PCIE3 /* PCIE controller 3 */
46 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
47 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
49 #define CONFIG_SYS_SRIO
50 #define CONFIG_SRIO1 /* SRIO port 1 */
51 #define CONFIG_SRIO2 /* SRIO port 2 */
52 #define CONFIG_SRIO_PCIE_BOOT_MASTER
53 #define CONFIG_SYS_DPAA_RMAN /* RMan */
55 #define CONFIG_ENV_OVERWRITE
57 #ifndef CONFIG_MTD_NOR_FLASH
59 #define CONFIG_FLASH_CFI_DRIVER
60 #define CONFIG_SYS_FLASH_CFI
61 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
64 #if defined(CONFIG_SPIFLASH)
65 #define CONFIG_SYS_EXTRA_ENV_RELOC
66 #define CONFIG_ENV_SPI_BUS 0
67 #define CONFIG_ENV_SPI_CS 0
68 #define CONFIG_ENV_SPI_MAX_HZ 10000000
69 #define CONFIG_ENV_SPI_MODE 0
70 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */
71 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
72 #define CONFIG_ENV_SECT_SIZE 0x10000
73 #elif defined(CONFIG_SDCARD)
74 #define CONFIG_SYS_EXTRA_ENV_RELOC
75 #define CONFIG_FSL_FIXED_MMC_LOCATION
76 #define CONFIG_SYS_MMC_ENV_DEV 0
77 #define CONFIG_ENV_SIZE 0x2000
78 #define CONFIG_ENV_OFFSET (512 * 1658)
79 #elif defined(CONFIG_NAND)
80 #define CONFIG_SYS_EXTRA_ENV_RELOC
81 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
82 #define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
83 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
84 #define CONFIG_ENV_ADDR 0xffe20000
85 #define CONFIG_ENV_SIZE 0x2000
86 #elif defined(CONFIG_ENV_IS_NOWHERE)
87 #define CONFIG_ENV_SIZE 0x2000
89 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \
90 - CONFIG_ENV_SECT_SIZE)
91 #define CONFIG_ENV_SIZE 0x2000
92 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
96 unsigned long get_board_sys_clk(unsigned long dummy);
98 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
101 * These can be toggled for performance analysis, otherwise use default.
103 #define CONFIG_SYS_CACHE_STASHING
104 #define CONFIG_BACKSIDE_L2_CACHE
105 #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
106 #define CONFIG_BTB /* toggle branch predition */
108 #define CONFIG_ENABLE_36BIT_PHYS
110 #ifdef CONFIG_PHYS_64BIT
111 #define CONFIG_ADDR_MAP
112 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
115 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */
116 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
117 #define CONFIG_SYS_MEMTEST_END 0x00400000
118 #define CONFIG_SYS_ALT_MEMTEST
119 #define CONFIG_PANIC_HANG /* do not reset board on panic */
122 * Config the L3 Cache as L3 SRAM
124 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
125 #ifdef CONFIG_PHYS_64BIT
126 #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \
127 CONFIG_RAMBOOT_TEXT_BASE)
129 #define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR
131 #define CONFIG_SYS_L3_SIZE (1024 << 10)
132 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
134 #ifdef CONFIG_PHYS_64BIT
135 #define CONFIG_SYS_DCSRBAR 0xf0000000
136 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
140 #define CONFIG_ID_EEPROM
141 #define CONFIG_SYS_I2C_EEPROM_NXID
142 #define CONFIG_SYS_EEPROM_BUS_NUM 0
143 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
144 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
149 #define CONFIG_VERY_BIG_RAM
150 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
151 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
153 #define CONFIG_DIMM_SLOTS_PER_CTLR 1
154 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
156 #define CONFIG_DDR_SPD
158 #define CONFIG_SYS_SPD_BUS_NUM 0
159 #define SPD_EEPROM_ADDRESS 0x52
160 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
163 * Local Bus Definitions
166 /* Set the local bus clock 1/8 of platform clock */
167 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8
170 * This board doesn't have a promjet connector.
171 * However, it uses commone corenet board LAW and TLB.
172 * It is necessary to use the same start address with proper offset.
174 #define CONFIG_SYS_FLASH_BASE 0xe0000000
175 #ifdef CONFIG_PHYS_64BIT
176 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
178 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
181 #define CONFIG_SYS_FLASH_BR_PRELIM \
182 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \
184 #define CONFIG_SYS_FLASH_OR_PRELIM \
185 ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
186 | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)
188 #define CONFIG_FSL_CPLD
189 #define CPLD_BASE 0xffdf0000 /* CPLD registers */
190 #ifdef CONFIG_PHYS_64BIT
191 #define CPLD_BASE_PHYS 0xfffdf0000ull
193 #define CPLD_BASE_PHYS CPLD_BASE
196 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V)
197 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */
199 #define PIXIS_LBMAP_SWITCH 7
200 #define PIXIS_LBMAP_MASK 0xf0
201 #define PIXIS_LBMAP_SHIFT 4
202 #define PIXIS_LBMAP_ALTBANK 0x40
204 #define CONFIG_SYS_FLASH_QUIET_TEST
205 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
207 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
208 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
209 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Erase Timeout (ms) */
210 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (ms) */
212 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
214 #if defined(CONFIG_RAMBOOT_PBL)
215 #define CONFIG_SYS_RAMBOOT
218 #define CONFIG_NAND_FSL_ELBC
220 #ifdef CONFIG_NAND_FSL_ELBC
221 #define CONFIG_SYS_NAND_BASE 0xffa00000
222 #ifdef CONFIG_PHYS_64BIT
223 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
225 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
228 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
229 #define CONFIG_SYS_MAX_NAND_DEVICE 1
230 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
232 /* NAND flash config */
233 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
234 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
235 | BR_PS_8 /* Port Size = 8 bit */ \
236 | BR_MS_FCM /* MSEL = FCM */ \
238 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
239 | OR_FCM_PGS /* Large Page*/ \
248 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
249 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
250 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
251 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
253 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
254 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
255 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
256 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
259 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
260 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
261 #endif /* CONFIG_NAND_FSL_ELBC */
263 #define CONFIG_SYS_FLASH_EMPTY_INFO
264 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
265 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
267 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
268 #define CONFIG_MISC_INIT_R
270 #define CONFIG_HWCONFIG
272 /* define to use L1 as initial stack */
273 #define CONFIG_L1_INIT_RAM
274 #define CONFIG_SYS_INIT_RAM_LOCK
275 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
276 #ifdef CONFIG_PHYS_64BIT
277 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
278 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
279 /* The assembler doesn't like typecast */
280 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
281 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
282 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
284 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
285 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
286 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
288 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
290 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
291 GENERATED_GBL_DATA_SIZE)
292 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
294 #define CONFIG_SYS_MONITOR_LEN (768 * 1024)
295 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
297 /* Serial Port - controlled on board with jumper J8
301 #define CONFIG_CONS_INDEX 1
302 #define CONFIG_SYS_NS16550_SERIAL
303 #define CONFIG_SYS_NS16550_REG_SIZE 1
304 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
306 #define CONFIG_SYS_BAUDRATE_TABLE \
307 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
309 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
310 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
311 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
312 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
315 #define CONFIG_SYS_I2C
316 #define CONFIG_SYS_I2C_FSL
317 #define CONFIG_SYS_FSL_I2C_SPEED 400000
318 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
319 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
320 #define CONFIG_SYS_FSL_I2C2_SPEED 400000
321 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
322 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
327 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
328 #ifdef CONFIG_PHYS_64BIT
329 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
331 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000
333 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
335 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
336 #ifdef CONFIG_PHYS_64BIT
337 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
339 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000
341 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
344 * for slave u-boot IMAGE instored in master memory space,
345 * PHYS must be aligned based on the SIZE
347 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
348 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
349 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
350 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
352 * for slave UCODE and ENV instored in master memory space,
353 * PHYS must be aligned based on the SIZE
355 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
356 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
357 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
359 /* slave core release by master*/
360 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
361 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
364 * SRIO_PCIE_BOOT - SLAVE
366 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
367 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
368 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
369 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
373 * eSPI - Enhanced SPI
375 #define CONFIG_SF_DEFAULT_SPEED 10000000
376 #define CONFIG_SF_DEFAULT_MODE 0
380 * Memory space is mapped 1-1, but I/O space must start from 0.
383 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
384 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
385 #ifdef CONFIG_PHYS_64BIT
386 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
387 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
389 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
390 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
392 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
393 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
394 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
395 #ifdef CONFIG_PHYS_64BIT
396 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
398 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
400 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
402 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
403 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
404 #ifdef CONFIG_PHYS_64BIT
405 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
406 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
408 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
409 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
411 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
412 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
413 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
414 #ifdef CONFIG_PHYS_64BIT
415 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
417 #define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
419 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
421 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
422 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000
423 #ifdef CONFIG_PHYS_64BIT
424 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
425 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
427 #define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000
428 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000
430 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
431 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
432 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
433 #ifdef CONFIG_PHYS_64BIT
434 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
436 #define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
438 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
441 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
442 #define CONFIG_SYS_BMAN_NUM_PORTALS 10
443 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
444 #ifdef CONFIG_PHYS_64BIT
445 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
447 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
449 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
450 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
451 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
452 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
453 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
454 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
455 CONFIG_SYS_BMAN_CENA_SIZE)
456 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
457 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
458 #define CONFIG_SYS_QMAN_NUM_PORTALS 10
459 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
460 #ifdef CONFIG_PHYS_64BIT
461 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
463 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
465 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
466 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
467 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
468 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
469 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
470 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
471 CONFIG_SYS_QMAN_CENA_SIZE)
472 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
473 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
475 #define CONFIG_SYS_DPAA_FMAN
476 #define CONFIG_SYS_DPAA_PME
477 /* Default address of microcode for the Linux Fman driver */
478 #if defined(CONFIG_SPIFLASH)
480 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
481 * env, so we got 0x110000.
483 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
484 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000
485 #elif defined(CONFIG_SDCARD)
487 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
488 * about 825KB (1650 blocks), Env is stored after the image, and the env size is
489 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
491 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
492 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
493 #elif defined(CONFIG_NAND)
494 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
495 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
496 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
498 * Slave has no ucode locally, it can fetch this from remote. When implementing
499 * in two corenet boards, slave's ucode could be stored in master's memory
500 * space, the address can be mapped from slave TLB->slave LAW->
501 * slave SRIO or PCIE outbound window->master inbound window->
502 * master LAW->the ucode address in master's memory space.
504 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
505 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
507 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
508 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
510 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
511 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
513 #ifdef CONFIG_SYS_DPAA_FMAN
514 #define CONFIG_FMAN_ENET
515 #define CONFIG_PHYLIB_10G
516 #define CONFIG_PHY_VITESSE
517 #define CONFIG_PHY_TERANETICS
521 #define CONFIG_PCI_INDIRECT_BRIDGE
523 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
524 #endif /* CONFIG_PCI */
527 #define CONFIG_FSL_SATA_V2
529 #ifdef CONFIG_FSL_SATA_V2
530 #define CONFIG_FSL_SATA
531 #define CONFIG_LIBATA
533 #define CONFIG_SYS_SATA_MAX_DEVICE 2
535 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
536 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
538 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
539 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
544 #ifdef CONFIG_FMAN_ENET
545 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2
546 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x3
547 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x4
548 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1
549 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x0
551 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c
552 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d
553 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e
554 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f
556 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0
558 #define CONFIG_SYS_TBIPA_VALUE 8
559 #define CONFIG_MII /* MII PHY management */
560 #define CONFIG_ETHPRIME "FM1@DTSEC1"
566 #define CONFIG_LOADS_ECHO /* echo on for serial download */
567 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
570 * Command line configuration.
576 #define CONFIG_HAS_FSL_DR_USB
577 #define CONFIG_HAS_FSL_MPH_USB
579 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
580 #define CONFIG_USB_EHCI_FSL
581 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
585 #define CONFIG_FSL_ESDHC
586 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
587 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
591 * Miscellaneous configurable options
593 #define CONFIG_SYS_LONGHELP /* undef to save memory */
594 #define CONFIG_CMDLINE_EDITING /* Command-line editing */
595 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */
596 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
597 #ifdef CONFIG_CMD_KGDB
598 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
600 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
602 /* Print Buffer Size */
603 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
604 sizeof(CONFIG_SYS_PROMPT)+16)
605 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
606 /* Boot Argument Buffer Size */
607 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
610 * For booting Linux, the board info and command line data
611 * have to be in the first 64 MB of memory, since this is
612 * the maximum mapped by the Linux kernel during initialization.
614 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */
615 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
617 #ifdef CONFIG_CMD_KGDB
618 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
622 * Environment Configuration
624 #define CONFIG_ROOTPATH "/opt/nfsroot"
625 #define CONFIG_BOOTFILE "uImage"
626 #define CONFIG_UBOOTPATH u-boot.bin
628 /* default location for tftp and bootm */
629 #define CONFIG_LOADADDR 1000000
631 #define __USB_PHY_TYPE utmi
633 #define CONFIG_EXTRA_ENV_SETTINGS \
634 "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
635 "bank_intlv=cs0_cs1\0" \
637 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
638 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
639 "tftpflash=tftpboot $loadaddr $uboot && " \
640 "protect off $ubootaddr +$filesize && " \
641 "erase $ubootaddr +$filesize && " \
642 "cp.b $loadaddr $ubootaddr $filesize && " \
643 "protect on $ubootaddr +$filesize && " \
644 "cmp.b $loadaddr $ubootaddr $filesize\0" \
645 "consoledev=ttyS0\0" \
646 "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
647 "usb_dr_mode=host\0" \
648 "ramdiskaddr=2000000\0" \
649 "ramdiskfile=p2041rdb/ramdisk.uboot\0" \
650 "fdtaddr=1e00000\0" \
651 "fdtfile=p2041rdb/p2041rdb.dtb\0" \
654 #define CONFIG_HDBOOT \
655 "setenv bootargs root=/dev/$bdev rw " \
656 "console=$consoledev,$baudrate $othbootargs;" \
657 "tftp $loadaddr $bootfile;" \
658 "tftp $fdtaddr $fdtfile;" \
659 "bootm $loadaddr - $fdtaddr"
661 #define CONFIG_NFSBOOTCOMMAND \
662 "setenv bootargs root=/dev/nfs rw " \
663 "nfsroot=$serverip:$rootpath " \
664 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
665 "console=$consoledev,$baudrate $othbootargs;" \
666 "tftp $loadaddr $bootfile;" \
667 "tftp $fdtaddr $fdtfile;" \
668 "bootm $loadaddr - $fdtaddr"
670 #define CONFIG_RAMBOOTCOMMAND \
671 "setenv bootargs root=/dev/ram rw " \
672 "console=$consoledev,$baudrate $othbootargs;" \
673 "tftp $ramdiskaddr $ramdiskfile;" \
674 "tftp $loadaddr $bootfile;" \
675 "tftp $fdtaddr $fdtfile;" \
676 "bootm $loadaddr $ramdiskaddr $fdtaddr"
678 #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
680 #include <asm/fsl_secure_boot.h>
682 #endif /* __CONFIG_H */