1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright 2013-2015 Arcturus Networks, Inc.
4 * http://www.arcturusnetworks.com/products/ucp1020/
5 * based on include/configs/p1_p2_rdb_pc.h
6 * original copyright follows:
7 * Copyright 2009-2011 Freescale Semiconductor, Inc.
11 * QorIQ uCP1020-xx boards configuration file
16 #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
17 #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
18 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
19 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
20 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
21 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
23 #if defined(CONFIG_TARTGET_UCP1020T1)
25 #define CONFIG_UCP1020_REV_1_3
27 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
31 #define CONFIG_HAS_ETH0
32 #define CONFIG_HAS_ETH1
33 #define CONFIG_ETHADDR 00:19:D3:FF:FF:FF
34 #define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE
35 #define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD
36 #define CONFIG_IPADDR 10.80.41.229
37 #define CONFIG_SERVERIP 10.80.41.227
38 #define CONFIG_NETMASK 255.255.252.0
39 #define CONFIG_ETHPRIME "eTSEC3"
41 #ifndef CONFIG_SPI_FLASH
43 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
45 #define CONFIG_SYS_L2_SIZE (256 << 10)
49 #if defined(CONFIG_TARGET_UCP1020)
51 #define CONFIG_UCP1020
52 #define CONFIG_UCP1020_REV_1_3
54 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
59 #define CONFIG_HAS_ETH0
60 #define CONFIG_HAS_ETH1
61 #define CONFIG_HAS_ETH2
62 #define CONFIG_ETHADDR 00:06:3B:FF:FF:FF
63 #define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE
64 #define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD
65 #define CONFIG_IPADDR 192.168.1.81
66 #define CONFIG_IPADDR1 192.168.1.82
67 #define CONFIG_IPADDR2 192.168.1.83
68 #define CONFIG_SERVERIP 192.168.1.80
69 #define CONFIG_GATEWAYIP 102.168.1.1
70 #define CONFIG_NETMASK 255.255.255.0
71 #define CONFIG_ETHPRIME "eTSEC1"
73 #ifndef CONFIG_SPI_FLASH
75 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
77 #define CONFIG_SYS_L2_SIZE (256 << 10)
82 #define CONFIG_RAMBOOT_SDCARD
83 #define CONFIG_SYS_RAMBOOT
84 #define CONFIG_SYS_EXTRA_ENV_RELOC
85 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
88 #ifdef CONFIG_SPIFLASH
89 #define CONFIG_RAMBOOT_SPIFLASH
90 #define CONFIG_SYS_RAMBOOT
91 #define CONFIG_SYS_EXTRA_ENV_RELOC
92 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
95 #define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000
97 #ifndef CONFIG_RESET_VECTOR_ADDRESS
98 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
101 #ifndef CONFIG_SYS_MONITOR_BASE
102 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
107 #define CONFIG_ENV_OVERWRITE
109 #define CONFIG_SYS_SATA_MAX_DEVICE 2
112 #define CONFIG_SYS_CLK_FREQ 66666666
113 #define CONFIG_DDR_CLK_FREQ 66666666
115 #define CONFIG_HWCONFIG
118 * These can be toggled for performance analysis, otherwise use default.
120 #define CONFIG_L2_CACHE
123 #define CONFIG_ENABLE_36BIT_PHYS
125 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
126 #define CONFIG_SYS_MEMTEST_END 0x1fffffff
128 #define CONFIG_SYS_CCSRBAR 0xffe00000
129 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
131 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
133 #ifdef CONFIG_SPL_BUILD
134 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
138 #define CONFIG_DDR_ECC_ENABLE
139 #ifndef CONFIG_DDR_ECC_ENABLE
140 #define CONFIG_SYS_DDR_RAW_TIMING
141 #define CONFIG_DDR_SPD
143 #define CONFIG_SYS_SPD_BUS_NUM 1
144 #undef CONFIG_FSL_DDR_INTERACTIVE
146 #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M
147 #define CONFIG_CHIP_SELECTS_PER_CTRL 1
148 #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
149 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
150 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
152 #define CONFIG_DIMM_SLOTS_PER_CTLR 1
154 /* Default settings for DDR3 */
155 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
156 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
157 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
158 #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f
159 #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302
160 #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000
162 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
163 #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
164 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
165 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
167 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
168 #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608
169 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000
170 #define CONFIG_SYS_DDR_RCW_1 0x00000000
171 #define CONFIG_SYS_DDR_RCW_2 0x00000000
172 #ifdef CONFIG_DDR_ECC_ENABLE
173 #define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */
175 #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */
177 #define CONFIG_SYS_DDR_CONTROL_2 0x04401050
178 #define CONFIG_SYS_DDR_TIMING_4 0x00220001
179 #define CONFIG_SYS_DDR_TIMING_5 0x03402400
181 #define CONFIG_SYS_DDR_TIMING_3 0x00020000
182 #define CONFIG_SYS_DDR_TIMING_0 0x00330004
183 #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846
184 #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF
185 #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000
186 #define CONFIG_SYS_DDR_MODE_1 0x40461520
187 #define CONFIG_SYS_DDR_MODE_2 0x8000c000
188 #define CONFIG_SYS_DDR_INTERVAL 0x0C300000
190 #undef CONFIG_CLOCKS_IN_MHZ
195 * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable
196 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2)
197 * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1
198 * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable
200 * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
201 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable
202 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
206 * Local Bus Definitions
208 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */
209 #define CONFIG_SYS_FLASH_BASE 0xec000000
211 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
213 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
216 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7
218 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
219 #define CONFIG_SYS_FLASH_QUIET_TEST
220 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
222 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
224 #undef CONFIG_SYS_FLASH_CHECKSUM
225 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
226 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
228 #define CONFIG_FLASH_CFI_DRIVER
229 #define CONFIG_SYS_FLASH_CFI
230 #define CONFIG_SYS_FLASH_EMPTY_INFO
231 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
233 #define CONFIG_SYS_INIT_RAM_LOCK
234 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
235 /* Initial L1 address */
236 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
237 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
238 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
239 /* Size of used area in RAM */
240 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
242 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
243 GENERATED_GBL_DATA_SIZE)
244 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
246 #define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */
247 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */
249 #define CONFIG_SYS_PMC_BASE 0xff980000
250 #define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE
251 #define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
253 #define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
254 OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
257 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
258 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
259 #ifdef CONFIG_NAND_FSL_ELBC
260 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
261 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
264 /* Serial Port - controlled on board with jumper J8
268 #undef CONFIG_SERIAL_SOFTWARE_FIFO
269 #define CONFIG_SYS_NS16550_SERIAL
270 #define CONFIG_SYS_NS16550_REG_SIZE 1
271 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
272 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
273 #define CONFIG_NS16550_MIN_FUNCTIONS
276 #define CONFIG_SYS_BAUDRATE_TABLE \
277 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
279 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
280 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
283 #define CONFIG_SYS_I2C
284 #define CONFIG_SYS_I2C_FSL
285 #define CONFIG_SYS_FSL_I2C_SPEED 400000
286 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
287 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
288 #define CONFIG_SYS_FSL_I2C2_SPEED 400000
289 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
290 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
291 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
292 #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
294 #define CONFIG_RTC_DS1337
295 #define CONFIG_RTC_DS1337_NOOSC
296 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
297 #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
298 #define CONFIG_SYS_I2C_NCT72_ADDR 0x4C
299 #define CONFIG_SYS_I2C_IDT6V49205B 0x69
302 * eSPI - Enhanced SPI
304 #define CONFIG_HARD_SPI
306 #define CONFIG_SF_DEFAULT_SPEED 10000000
307 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
309 #if defined(CONFIG_PCI)
312 * Memory space is mapped 1-1, but I/O space must start from 0.
315 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
316 #define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9"
317 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
318 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
319 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
320 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
321 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
322 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
323 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
324 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
326 /* controller 1, Slot 2, tgtid 1, Base address a000 */
327 #define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10"
328 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
329 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
330 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
331 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
332 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
333 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
334 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
335 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
337 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
338 #endif /* CONFIG_PCI */
343 #ifdef CONFIG_ENV_FIT_UCBOOT
345 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000)
346 #define CONFIG_ENV_SIZE 0x20000
347 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
351 #define CONFIG_ENV_SPI_BUS 0
352 #define CONFIG_ENV_SPI_CS 0
353 #define CONFIG_ENV_SPI_MAX_HZ 10000000
354 #define CONFIG_ENV_SPI_MODE 0
356 #ifdef CONFIG_RAMBOOT_SPIFLASH
358 #define CONFIG_ENV_SIZE 0x3000 /* 12KB */
359 #define CONFIG_ENV_OFFSET 0x2000 /* 8KB */
360 #define CONFIG_ENV_SECT_SIZE 0x1000
362 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
363 /* Address and size of Redundant Environment Sector */
364 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
365 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
368 #elif defined(CONFIG_RAMBOOT_SDCARD)
369 #define CONFIG_FSL_FIXED_MMC_LOCATION
370 #define CONFIG_ENV_SIZE 0x2000
371 #define CONFIG_SYS_MMC_ENV_DEV 0
373 #elif defined(CONFIG_SYS_RAMBOOT)
374 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
375 #define CONFIG_ENV_SIZE 0x2000
378 #define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE)
379 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
380 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
381 #define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000)
382 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
383 /* Address and size of Redundant Environment Sector */
384 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
385 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
390 #endif /* CONFIG_ENV_FIT_UCBOOT */
392 #define CONFIG_LOADS_ECHO /* echo on for serial download */
393 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
398 #define CONFIG_HAS_FSL_DR_USB
400 #if defined(CONFIG_HAS_FSL_DR_USB)
401 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
403 #ifdef CONFIG_USB_EHCI_HCD
404 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
405 #define CONFIG_USB_EHCI_FSL
409 #undef CONFIG_WATCHDOG /* watchdog disabled */
412 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
413 #define CONFIG_MMC_SPI
416 /* Misc Extra Settings */
417 #undef CONFIG_WATCHDOG /* watchdog disabled */
420 * Miscellaneous configurable options
422 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
423 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */
426 * For booting Linux, the board info and command line data
427 * have to be in the first 64 MB of memory, since this is
428 * the maximum mapped by the Linux kernel during initialization.
430 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/
431 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
433 #if defined(CONFIG_CMD_KGDB)
434 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
435 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
439 * Environment Configuration
442 #if defined(CONFIG_TSEC_ENET)
444 #if defined(CONFIG_UCP1020_REV_1_2) || defined(CONFIG_UCP1020_REV_1_3)
446 #error "UCP1020 module revision is not defined !!!"
449 #define CONFIG_BOOTP_SERVERIP
451 #define CONFIG_MII /* MII PHY management */
452 #define CONFIG_TSEC1_NAME "eTSEC1"
453 #define CONFIG_TSEC2_NAME "eTSEC2"
454 #define CONFIG_TSEC3_NAME "eTSEC3"
456 #define TSEC1_PHY_ADDR 4
457 #define TSEC2_PHY_ADDR 0
458 #define TSEC2_PHY_ADDR_SGMII 0x00
459 #define TSEC3_PHY_ADDR 6
461 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
462 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
463 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
465 #define TSEC1_PHYIDX 0
466 #define TSEC2_PHYIDX 0
467 #define TSEC3_PHYIDX 0
471 #define CONFIG_HOSTNAME "UCP1020"
472 #define CONFIG_ROOTPATH "/opt/nfsroot"
473 #define CONFIG_BOOTFILE "uImage"
474 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
476 /* default location for tftp and bootm */
477 #define CONFIG_LOADADDR 1000000
479 #if defined(CONFIG_DONGLE)
481 #define CONFIG_EXTRA_ENV_SETTINGS \
482 "bootcmd=run prog_spi_mbrbootcramfs\0" \
483 "bootfile=uImage\0" \
484 "consoledev=ttyS0\0" \
485 "cramfsfile=image.cramfs\0" \
486 "dtbaddr=0x00c00000\0" \
487 "dtbfile=image.dtb\0" \
488 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
489 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
490 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
491 "fileaddr=0x01000000\0" \
492 "filesize=0x00080000\0" \
493 "flashmbr=sf probe 0; " \
494 "tftp $loadaddr $mbr; " \
495 "sf erase $mbr_offset +$filesize; " \
496 "sf write $loadaddr $mbr_offset $filesize\0" \
497 "flashrecovery=tftp $recoveryaddr $cramfsfile; " \
498 "protect off $nor_recoveryaddr +$filesize; " \
499 "erase $nor_recoveryaddr +$filesize; " \
500 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \
501 "protect on $nor_recoveryaddr +$filesize\0 " \
502 "flashuboot=tftp $ubootaddr $ubootfile; " \
503 "protect off $nor_ubootaddr +$filesize; " \
504 "erase $nor_ubootaddr +$filesize; " \
505 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \
506 "protect on $nor_ubootaddr +$filesize\0 " \
507 "flashworking=tftp $workingaddr $cramfsfile; " \
508 "protect off $nor_workingaddr +$filesize; " \
509 "erase $nor_workingaddr +$filesize; " \
510 "cp.b $workingaddr $nor_workingaddr $filesize; " \
511 "protect on $nor_workingaddr +$filesize\0 " \
512 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
513 "kerneladdr=0x01100000\0" \
514 "kernelfile=uImage\0" \
515 "loadaddr=0x01000000\0" \
516 "mbr=uCP1020d.mbr\0" \
517 "mbr_offset=0x00000000\0" \
518 "mmbr=uCP1020Quiet.mbr\0" \
520 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \
522 "mmc write $loadaddr 1 1\0" \
523 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \
524 "mmc erase 0x40 0x400; " \
525 "mmc write $loadaddr 0x40 0x400\0" \
527 "nor_recoveryaddr=0xEC0A0000\0" \
528 "nor_ubootaddr=0xEFF80000\0" \
529 "nor_workingaddr=0xECFA0000\0" \
530 "norbootrecovery=setenv bootargs $recoverybootargs" \
531 " console=$consoledev,$baudrate $othbootargs; " \
532 "run norloadrecovery; " \
533 "bootm $kerneladdr - $dtbaddr\0" \
534 "norbootworking=setenv bootargs $workingbootargs" \
535 " console=$consoledev,$baudrate $othbootargs; " \
536 "run norloadworking; " \
537 "bootm $kerneladdr - $dtbaddr\0" \
538 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \
539 "setenv cramfsaddr $nor_recoveryaddr; " \
540 "cramfsload $dtbaddr $dtbfile; " \
541 "cramfsload $kerneladdr $kernelfile\0" \
542 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \
543 "setenv cramfsaddr $nor_workingaddr; " \
544 "cramfsload $dtbaddr $dtbfile; " \
545 "cramfsload $kerneladdr $kernelfile\0" \
546 "prog_spi_mbr=run spi__mbr\0" \
547 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \
548 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
549 "run spi__cramfs\0" \
550 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
551 " console=$consoledev,$baudrate $othbootargs; " \
552 "tftp $rootfsaddr $rootfsfile; " \
553 "tftp $loadaddr $kernelfile; " \
554 "tftp $dtbaddr $dtbfile; " \
555 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
556 "ramdisk_size=120000\0" \
557 "ramdiskfile=rootfs.ext2.gz.uboot\0" \
558 "recoveryaddr=0x02F00000\0" \
559 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \
560 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
561 "mw.l 0xffe0f008 0x00400000\0" \
562 "rootfsaddr=0x02F00000\0" \
563 "rootfsfile=rootfs.ext2.gz.uboot\0" \
564 "rootpath=/opt/nfsroot\0" \
565 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
566 "protect off 0xeC000000 +$filesize; " \
567 "erase 0xEC000000 +$filesize; " \
568 "cp.b $loadaddr 0xEC000000 $filesize; " \
569 "cmp.b $loadaddr 0xEC000000 $filesize; " \
570 "protect on 0xeC000000 +$filesize\0" \
571 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
572 "protect off 0xeFF80000 +$filesize; " \
573 "erase 0xEFF80000 +$filesize; " \
574 "cp.b $loadaddr 0xEFF80000 $filesize; " \
575 "cmp.b $loadaddr 0xEFF80000 $filesize; " \
576 "protect on 0xeFF80000 +$filesize\0" \
577 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \
578 "sf probe 0; sf erase 0x8000 +$filesize; " \
579 "sf write $loadaddr 0x8000 $filesize\0" \
580 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \
581 "protect off 0xec0a0000 +$filesize; " \
582 "erase 0xeC0A0000 +$filesize; " \
583 "cp.b $loadaddr 0xeC0A0000 $filesize; " \
584 "protect on 0xec0a0000 +$filesize\0" \
585 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \
586 "sf probe 1; sf erase 0 +$filesize; " \
587 "sf write $loadaddr 0 $filesize\0" \
588 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \
589 "sf probe 0; sf erase 0 +$filesize; " \
590 "sf write $loadaddr 0 $filesize\0" \
591 "tftpflash=tftpboot $loadaddr $uboot; " \
592 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
593 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
594 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
595 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
596 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
597 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
598 "ubootaddr=0x01000000\0" \
599 "ubootfile=u-boot.bin\0" \
600 "ubootd=u-boot4dongle.bin\0" \
601 "upgrade=run flashworking\0" \
602 "usb_phy_type=ulpi\0 " \
603 "workingaddr=0x02F00000\0" \
604 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
608 #if defined(CONFIG_UCP1020T1)
610 #define CONFIG_EXTRA_ENV_SETTINGS \
611 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \
612 "bootfile=uImage\0" \
613 "consoledev=ttyS0\0" \
614 "cramfsfile=image.cramfs\0" \
615 "dtbaddr=0x00c00000\0" \
616 "dtbfile=image.dtb\0" \
617 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
618 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
619 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
620 "fileaddr=0x01000000\0" \
621 "filesize=0x00080000\0" \
622 "flashmbr=sf probe 0; " \
623 "tftp $loadaddr $mbr; " \
624 "sf erase $mbr_offset +$filesize; " \
625 "sf write $loadaddr $mbr_offset $filesize\0" \
626 "flashrecovery=tftp $recoveryaddr $cramfsfile; " \
627 "protect off $nor_recoveryaddr +$filesize; " \
628 "erase $nor_recoveryaddr +$filesize; " \
629 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \
630 "protect on $nor_recoveryaddr +$filesize\0 " \
631 "flashuboot=tftp $ubootaddr $ubootfile; " \
632 "protect off $nor_ubootaddr +$filesize; " \
633 "erase $nor_ubootaddr +$filesize; " \
634 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \
635 "protect on $nor_ubootaddr +$filesize\0 " \
636 "flashworking=tftp $workingaddr $cramfsfile; " \
637 "protect off $nor_workingaddr +$filesize; " \
638 "erase $nor_workingaddr +$filesize; " \
639 "cp.b $workingaddr $nor_workingaddr $filesize; " \
640 "protect on $nor_workingaddr +$filesize\0 " \
641 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
642 "kerneladdr=0x01100000\0" \
643 "kernelfile=uImage\0" \
644 "loadaddr=0x01000000\0" \
645 "mbr=uCP1020.mbr\0" \
646 "mbr_offset=0x00000000\0" \
648 "nor_recoveryaddr=0xEC0A0000\0" \
649 "nor_ubootaddr=0xEFF80000\0" \
650 "nor_workingaddr=0xECFA0000\0" \
651 "norbootrecovery=setenv bootargs $recoverybootargs" \
652 " console=$consoledev,$baudrate $othbootargs; " \
653 "run norloadrecovery; " \
654 "bootm $kerneladdr - $dtbaddr\0" \
655 "norbootworking=setenv bootargs $workingbootargs" \
656 " console=$consoledev,$baudrate $othbootargs; " \
657 "run norloadworking; " \
658 "bootm $kerneladdr - $dtbaddr\0" \
659 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \
660 "setenv cramfsaddr $nor_recoveryaddr; " \
661 "cramfsload $dtbaddr $dtbfile; " \
662 "cramfsload $kerneladdr $kernelfile\0" \
663 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \
664 "setenv cramfsaddr $nor_workingaddr; " \
665 "cramfsload $dtbaddr $dtbfile; " \
666 "cramfsload $kerneladdr $kernelfile\0" \
667 "othbootargs=quiet\0" \
668 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
669 " console=$consoledev,$baudrate $othbootargs; " \
670 "tftp $rootfsaddr $rootfsfile; " \
671 "tftp $loadaddr $kernelfile; " \
672 "tftp $dtbaddr $dtbfile; " \
673 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
674 "ramdisk_size=120000\0" \
675 "ramdiskfile=rootfs.ext2.gz.uboot\0" \
676 "recoveryaddr=0x02F00000\0" \
677 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \
678 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
679 "mw.l 0xffe0f008 0x00400000\0" \
680 "rootfsaddr=0x02F00000\0" \
681 "rootfsfile=rootfs.ext2.gz.uboot\0" \
682 "rootpath=/opt/nfsroot\0" \
684 "tftpflash=tftpboot $loadaddr $uboot; " \
685 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
686 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
687 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
688 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
689 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
690 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
691 "ubootaddr=0x01000000\0" \
692 "ubootfile=u-boot.bin\0" \
693 "upgrade=run flashworking\0" \
694 "workingaddr=0x02F00000\0" \
695 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
697 #else /* For Arcturus Modules */
699 #define CONFIG_EXTRA_ENV_SETTINGS \
700 "bootcmd=run norkernel\0" \
701 "bootfile=uImage\0" \
702 "consoledev=ttyS0\0" \
703 "dtbaddr=0x00c00000\0" \
704 "dtbfile=image.dtb\0" \
705 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
706 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
707 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
708 "fileaddr=0x01000000\0" \
709 "filesize=0x00080000\0" \
710 "flashmbr=sf probe 0; " \
711 "tftp $loadaddr $mbr; " \
712 "sf erase $mbr_offset +$filesize; " \
713 "sf write $loadaddr $mbr_offset $filesize\0" \
714 "flashuboot=tftp $loadaddr $ubootfile; " \
715 "protect off $nor_ubootaddr0 +$filesize; " \
716 "erase $nor_ubootaddr0 +$filesize; " \
717 "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \
718 "protect on $nor_ubootaddr0 +$filesize; " \
719 "protect off $nor_ubootaddr1 +$filesize; " \
720 "erase $nor_ubootaddr1 +$filesize; " \
721 "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \
722 "protect on $nor_ubootaddr1 +$filesize\0 " \
723 "format0=protect off $part0base +$part0size; " \
724 "erase $part0base +$part0size\0" \
725 "format1=protect off $part1base +$part1size; " \
726 "erase $part1base +$part1size\0" \
727 "format2=protect off $part2base +$part2size; " \
728 "erase $part2base +$part2size\0" \
729 "format3=protect off $part3base +$part3size; " \
730 "erase $part3base +$part3size\0" \
731 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
732 "kerneladdr=0x01100000\0" \
733 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \
734 "kernelfile=uImage\0" \
735 "loadaddr=0x01000000\0" \
736 "mbr=uCP1020.mbr\0" \
737 "mbr_offset=0x00000000\0" \
739 "nor_ubootaddr0=0xEC000000\0" \
740 "nor_ubootaddr1=0xEFF80000\0" \
741 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
742 "run norkernelload; " \
743 "bootm $kerneladdr - $dtbaddr\0" \
744 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \
745 "setenv cramfsaddr $part0base; " \
746 "cramfsload $dtbaddr $dtbfile; " \
747 "cramfsload $kerneladdr $kernelfile\0" \
748 "part0base=0xEC100000\0" \
749 "part0size=0x00700000\0" \
750 "part1base=0xEC800000\0" \
751 "part1size=0x02000000\0" \
752 "part2base=0xEE800000\0" \
753 "part2size=0x00800000\0" \
754 "part3base=0xEF000000\0" \
755 "part3size=0x00F80000\0" \
756 "partENVbase=0xEC080000\0" \
757 "partENVsize=0x00080000\0" \
758 "program0=tftp part0-000000.bin; " \
759 "protect off $part0base +$filesize; " \
760 "erase $part0base +$filesize; " \
761 "cp.b $loadaddr $part0base $filesize; " \
762 "echo Verifying...; " \
763 "cmp.b $loadaddr $part0base $filesize\0" \
764 "program1=tftp part1-000000.bin; " \
765 "protect off $part1base +$filesize; " \
766 "erase $part1base +$filesize; " \
767 "cp.b $loadaddr $part1base $filesize; " \
768 "echo Verifying...; " \
769 "cmp.b $loadaddr $part1base $filesize\0" \
770 "program2=tftp part2-000000.bin; " \
771 "protect off $part2base +$filesize; " \
772 "erase $part2base +$filesize; " \
773 "cp.b $loadaddr $part2base $filesize; " \
774 "echo Verifying...; " \
775 "cmp.b $loadaddr $part2base $filesize\0" \
776 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
777 " console=$consoledev,$baudrate $othbootargs; " \
778 "tftp $rootfsaddr $rootfsfile; " \
779 "tftp $loadaddr $kernelfile; " \
780 "tftp $dtbaddr $dtbfile; " \
781 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
782 "ramdisk_size=120000\0" \
783 "ramdiskfile=rootfs.ext2.gz.uboot\0" \
784 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
785 "mw.l 0xffe0f008 0x00400000\0" \
786 "rootfsaddr=0x02F00000\0" \
787 "rootfsfile=rootfs.ext2.gz.uboot\0" \
788 "rootpath=/opt/nfsroot\0" \
789 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \
790 "sf probe 0; sf erase 0 +$filesize; " \
791 "sf write $loadaddr 0 $filesize\0" \
792 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
793 "protect off 0xeC000000 +$filesize; " \
794 "erase 0xEC000000 +$filesize; " \
795 "cp.b $loadaddr 0xEC000000 $filesize; " \
796 "cmp.b $loadaddr 0xEC000000 $filesize; " \
797 "protect on 0xeC000000 +$filesize\0" \
798 "tftpflash=tftpboot $loadaddr $uboot; " \
799 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
800 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
801 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
802 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
803 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
804 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
805 "ubootfile=u-boot.bin\0" \
806 "upgrade=run flashuboot\0" \
807 "usb_phy_type=ulpi\0 " \
809 "setenv bootargs root=/dev/nfs rw " \
810 "nfsroot=$serverip:$rootpath " \
811 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
812 "console=$consoledev,$baudrate $othbootargs;" \
813 "tftp $loadaddr $bootfile;" \
814 "tftp $fdtaddr $fdtfile;" \
815 "bootm $loadaddr - $fdtaddr\0" \
817 "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
818 "console=$consoledev,$baudrate $othbootargs;" \
820 "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
821 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
822 "bootm $loadaddr - $fdtaddr\0" \
824 "setenv bootargs root=/dev/ram rw " \
825 "console=$consoledev,$baudrate $othbootargs " \
826 "ramdisk_size=$ramdisk_size;" \
828 "fatload usb 0:2 $loadaddr $bootfile;" \
829 "fatload usb 0:2 $fdtaddr $fdtfile;" \
830 "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \
831 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \
833 "setenv bootargs root=/dev/ram rw " \
834 "console=$consoledev,$baudrate $othbootargs " \
835 "ramdisk_size=$ramdisk_size;" \
837 "ext2load usb 0:4 $loadaddr $bootfile;" \
838 "ext2load usb 0:4 $fdtaddr $fdtfile;" \
839 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
840 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \
842 "setenv bootargs root=/dev/$jffs2nor rw " \
843 "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \
844 "bootm $norbootaddr - $norfdtaddr\0 " \
846 "setenv bootargs root=/dev/ram rw " \
847 "console=$consoledev,$baudrate $othbootargs " \
848 "ramdisk_size=$ramdisk_size;" \
849 "tftp $ramdiskaddr $ramdiskfile;" \
850 "tftp $loadaddr $bootfile;" \
851 "tftp $fdtaddr $fdtfile;" \
852 "bootm $loadaddr $ramdiskaddr $fdtaddr\0"
857 #endif /* __CONFIG_H */