2 * am3517_evm.h - Default configuration for AM3517 EVM board.
4 * Author: Vaibhav Hiremath <hvaibhav@ti.com>
6 * Based on omap3_evm_config.h
8 * Copyright (C) 2010 Texas Instruments Incorporated
10 * SPDX-License-Identifier: GPL-2.0+
16 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
19 * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
20 * 64 bytes before this address should be set aside for u-boot.img's
21 * header. That is 0x800FFFC0--0x80100000 should not be used for any
25 #define CONFIG_SYS_SPL_MALLOC_START 0x80208000
26 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
28 #include <configs/ti_omap3_common.h>
29 #undef CONFIG_SDRC /* Disable SDRC since we have EMIF4 */
31 #define CONFIG_MISC_INIT_R
32 #define CONFIG_REVISION_TAG
34 /* Hardware drivers */
36 /* allow to overwrite serial and ethaddr */
37 #define CONFIG_ENV_OVERWRITE
41 * Enable CONFIG_USB_MUSB_HOST for Host functionalities MSC, keyboard
42 * Enable CONFIG_USB_MUSB_GADGET for Device functionalities.
45 #ifdef CONFIG_USB_MUSB_AM35X
47 #ifdef CONFIG_USB_MUSB_HOST
49 #ifdef CONFIG_USB_KEYBOARD
50 #define CONFIG_PREBOOT "usb start"
51 #endif /* CONFIG_USB_KEYBOARD */
53 #endif /* CONFIG_USB_MUSB_HOST */
55 #endif /* CONFIG_USB_MUSB_AM35X */
60 #define CONFIG_DRIVER_TI_EMAC
61 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
63 #define CONFIG_BOOTP_DEFAULT
64 #define CONFIG_BOOTP_DNS
65 #define CONFIG_BOOTP_DNS2
66 #define CONFIG_BOOTP_SEND_HOSTNAME
67 #define CONFIG_NET_RETRY_COUNT 10
69 /* Board NAND Info. */
71 #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
73 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
74 #define CONFIG_SYS_NAND_PAGE_COUNT 64
75 #define CONFIG_SYS_NAND_PAGE_SIZE 2048
76 #define CONFIG_SYS_NAND_OOBSIZE 64
77 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
78 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
79 #define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, 10, \
80 11, 12, 13, 14, 16, 17, 18, 19, 20, \
81 21, 22, 23, 24, 25, 26, 27, 28, 30, \
82 31, 32, 33, 34, 35, 36, 37, 38, 39, \
83 40, 41, 42, 44, 45, 46, 47, 48, 49, \
84 50, 51, 52, 53, 54, 55, 56 }
86 #define CONFIG_SYS_NAND_ECCSIZE 512
87 #define CONFIG_SYS_NAND_ECCBYTES 13
88 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
89 #define CONFIG_SYS_NAND_MAX_OOBFREE 2
90 #define CONFIG_SYS_NAND_MAX_ECCPOS 56
91 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
92 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
93 #define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
94 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
95 /* NAND block size is 128 KiB. Synchronize these values with
96 * corresponding Device Tree entries in Linux:
97 * MLO(SPL) 4 * NAND_BLOCK_SIZE = 512 KiB @ 0x000000
98 * U-Boot 15 * NAND_BLOCK_SIZE = 1920 KiB @ 0x080000
99 * U-Boot environment 2 * NAND_BLOCK_SIZE = 256 KiB @ 0x260000
100 * Kernel 64 * NAND_BLOCK_SIZE = 8 MiB @ 0x2A0000
101 * DTB 4 * NAND_BLOCK_SIZE = 512 KiB @ 0xAA0000
102 * RootFS Remaining Flash Space @ 0xB20000
104 #endif /* CONFIG_NAND */
106 /* Environment information */
108 #define CONFIG_BOOTFILE "uImage"
110 #define CONFIG_EXTRA_ENV_SETTINGS \
111 "loadaddr=0x82000000\0" \
112 "console=ttyO2,115200n8\0" \
113 "fdtfile=am3517-evm.dtb\0" \
114 "fdtaddr=0x82C00000\0" \
116 "bootenv=uEnv.txt\0" \
119 "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
120 "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
123 "mmcroot=/dev/mmcblk0p2 rw\0" \
124 "mmcrootfstype=ext4 rootwait fixrtc\0" \
125 "mmcargs=setenv bootargs console=${console} " \
129 "rootfstype=${mmcrootfstype} " \
131 "nandargs=setenv bootargs console=${console} " \
134 "root=ubi0:rootfs rw ubi.mtd=rootfs " \
135 "rootfstype=ubifs rootwait " \
137 "loadbootenv=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootenv}\0"\
138 "importbootenv=echo Importing environment from mmc ...; " \
139 "env import -t ${loadaddr} ${filesize}\0" \
140 "bootscript=echo Running bootscript from mmc ...; " \
141 "source ${loadaddr}\0" \
142 "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootfile}\0" \
143 "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdtaddr} ${fdtfile}\0" \
144 "mmcboot=echo Booting from mmc ...; " \
146 "bootz ${loadaddr} - ${fdtaddr}\0" \
147 "nandboot=echo Booting from nand ...; " \
149 "nand read ${loadaddr} 2a0000 800000; " \
150 "nand read ${fdtaddr} aa0000 80000; " \
151 "bootm ${loadaddr} - ${fdtaddr}\0" \
153 #define CONFIG_BOOTCOMMAND \
154 "mmc dev ${mmcdev}; if mmc rescan; then " \
155 "echo SD/MMC found on device $mmcdev; " \
156 "if run loadbootenv; then " \
157 "run importbootenv; " \
159 "echo Checking if uenvcmd is set ...; " \
160 "if test -n $uenvcmd; then " \
161 "echo Running uenvcmd ...; " \
164 "echo Running default loadimage ...; " \
165 "setenv bootfile zImage; " \
166 "if run loadimage; then " \
170 "else run nandboot; fi"
172 /* Miscellaneous configurable options */
173 #define CONFIG_AUTO_COMPLETE
174 #define CONFIG_CMDLINE_EDITING
175 #define CONFIG_SYS_LONGHELP
177 /* We set the max number of command args high to avoid HUSH bugs. */
178 #define CONFIG_SYS_MAXARGS 64
180 /* Print Buffer Size */
181 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
182 + sizeof(CONFIG_SYS_PROMPT) + 16)
183 /* Boot Argument Buffer Size */
184 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
186 /* memtest works on */
187 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
188 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
189 0x01F00000) /* 31MB */
191 /* Physical Memory Map */
192 #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
193 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
194 #define CONFIG_SYS_INIT_RAM_SIZE 0x800
196 /* FLASH and environment organization */
198 /* **** PISMO SUPPORT *** */
199 #define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */
201 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
202 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
204 #if defined(CONFIG_NAND)
205 #define CONFIG_SYS_FLASH_BASE NAND_BASE
208 /* Monitor at start of flash */
209 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
211 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
212 #define CONFIG_ENV_SIZE CONFIG_SYS_ENV_SECT_SIZE
213 #define CONFIG_ENV_OFFSET 0x260000
214 #define CONFIG_ENV_ADDR 0x260000
216 /* Defines for SPL */
217 #undef CONFIG_SPL_TEXT_BASE
218 #define CONFIG_SPL_TEXT_BASE 0x40200000
220 #undef CONFIG_SPL_BSS_START_ADDR
221 #define CONFIG_SPL_BSS_START_ADDR 0x80000000
222 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
224 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
225 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
227 #define CONFIG_SPL_NAND_BASE
228 #define CONFIG_SPL_NAND_DRIVERS
229 #define CONFIG_SPL_NAND_ECC
231 #endif /* __CONFIG_H */