2 * Configuation settings for the Sentec Cobra Board.
4 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
6 * See file CREDITS for list of people who contributed to this
9 * This program is free software; you can redistribute it and/or
10 * modify it under the terms of the GNU General Public License as
11 * published by the Free Software Foundation; either version 2 of
12 * the License, or (at your option) any later version.
14 * This program is distributed in the hope that it will be useful,
15 * but WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17 * GNU General Public License for more details.
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software
21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
26 * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board
28 * Author: Florian Schlote
30 * For a description of configuration options please refer also to the
31 * general u-boot-1.x.x/README file
36 * board/config.h - configuration options, board specific
40 #ifndef _CONFIG_COBRA5272_H
41 #define _CONFIG_COBRA5272_H
45 * possible values for Sentec board: only Coldfire M5272 processor supported
46 * (please do not change)
50 #define CONFIG_MCF52x2 /* define processor family */
51 #define CONFIG_M5272 /* define processor type */
54 * Defines processor clock - important for correct timings concerning serial
56 * CONFIG_SYS_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms
60 #define CONFIG_SYS_HZ 1000
61 #define CONFIG_SYS_CLK 66000000
62 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
65 * Enable use of Ethernet
70 /* Enable Dma Timer */
74 * Define baudrate for UART1 (console output, tftp, ...)
75 * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
76 * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command
81 #define CONFIG_MCFUART
82 #define CONFIG_SYS_UART_PORT (0)
83 #define CONFIG_BAUDRATE 19200
84 #define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
87 * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
88 * timeout acc. to your needs
89 * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000
95 #define CONFIG_WATCHDOG
96 #define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */
100 * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different
101 * bootloader residing in flash ('chainloading'); if you want to use
102 * chainloading or want to compile a u-boot binary that can be loaded into
105 * You will need a first stage bootloader then, e. g. colilo or a working BDM
106 * cable (Background Debug Mode)
108 * Setting #if 0: u-boot will start from flash and relocate itself to RAM
110 * Please do not forget to modify the setting of TEXT_BASE
111 * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000)
117 #define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */
121 * Configuration for environment
122 * Environment is embedded in u-boot in the second sector of the flash
126 #ifndef CONFIG_MONITOR_IS_IN_RAM
127 #define CONFIG_ENV_OFFSET 0x4000
128 #define CONFIG_ENV_SECT_SIZE 0x2000
129 #define CONFIG_ENV_IS_IN_FLASH 1
131 #define CONFIG_ENV_ADDR 0xffe04000
132 #define CONFIG_ENV_SECT_SIZE 0x2000
133 #define CONFIG_ENV_IS_IN_FLASH 1
140 #define CONFIG_BOOTP_BOOTFILESIZE
141 #define CONFIG_BOOTP_BOOTPATH
142 #define CONFIG_BOOTP_GATEWAY
143 #define CONFIG_BOOTP_HOSTNAME
147 * Command line configuration.
149 #include <config_cmd_default.h>
151 #define CONFIG_CMD_PING
153 #undef CONFIG_CMD_LOADS
154 #undef CONFIG_CMD_LOADB
155 #undef CONFIG_CMD_MII
158 # define CONFIG_NET_MULTI 1
159 # define CONFIG_MII 1
160 # define CONFIG_MII_INIT 1
161 # define CONFIG_SYS_DISCOVER_PHY
162 # define CONFIG_SYS_RX_ETH_BUFFER 8
163 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
165 # define CONFIG_SYS_FEC0_PINMUX 0
166 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
167 # define MCFFEC_TOUT_LOOP 50000
168 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
169 # ifndef CONFIG_SYS_DISCOVER_PHY
170 # define FECDUPLEX FULL
171 # define FECSPEED _100BASET
173 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
174 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
176 # endif /* CONFIG_SYS_DISCOVER_PHY */
180 *-----------------------------------------------------------------------------
181 * Define user parameters that have to be customized most likely
182 *-----------------------------------------------------------------------------
185 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/
187 #define CONFIG_BOOTDELAY 5 /* used for autoboot, delay in
188 seconds u-boot will wait before starting defined (auto-)boot command, setting
189 to -1 disables delay, setting to 0 will too prevent access to u-boot command
190 interface: u-boot then has to reflashed */
193 /* The following settings will be contained in the environment block ; if you
194 want to use a neutral environment all those settings can be manually set in
195 u-boot: 'set' command */
199 #define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please
200 enter a valid image address in flash */
202 #define CONFIG_BOOTARGS " " /* default bootargs that are
203 considered during boot */
205 /* User network settings */
207 #define CONFIG_ETHADDR 00:00:00:00:00:09 /* default ethernet MAC addr. */
208 #define CONFIG_IPADDR 192.168.100.2 /* default board IP address */
209 #define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */
213 #define CONFIG_SYS_PROMPT "COBRA > " /* Layout of u-boot prompt*/
215 #define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address
216 from which user programs will be started */
220 #define CONFIG_SYS_LONGHELP /* undef to save memory */
222 #if defined(CONFIG_CMD_KGDB)
223 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
225 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
227 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
228 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
229 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
232 *-----------------------------------------------------------------------------
233 * End of user parameters to be customized
234 *-----------------------------------------------------------------------------
238 * Defines memory range for test
242 #define CONFIG_SYS_MEMTEST_START 0x400
243 #define CONFIG_SYS_MEMTEST_END 0x380000
246 * Low Level Configuration Settings
247 * (address mappings, register initial values, etc.)
248 * You should know what you are doing if you make changes here.
253 * Base register address
257 #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */
260 * System Conf. Reg. & System Protection Reg.
264 #define CONFIG_SYS_SCR 0x0003
265 #define CONFIG_SYS_SPR 0xffff
272 #define CONFIG_SYS_DISCOVER_PHY
273 #define CONFIG_SYS_ENET_BD_BASE 0x780000
275 /*-----------------------------------------------------------------------
276 * Definitions for initial stack pointer and data area (in internal SRAM)
278 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
279 #define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */
280 #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
281 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
282 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
284 /*-----------------------------------------------------------------------
285 * Start addresses for the final memory configuration
286 * (Set up by the startup code)
287 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
289 #define CONFIG_SYS_SDRAM_BASE 0x00000000
292 *-------------------------------------------------------------------------
293 * RAM SIZE (is defined above)
294 *-----------------------------------------------------------------------
297 /* #define CONFIG_SYS_SDRAM_SIZE 16 */
300 *-----------------------------------------------------------------------
303 #define CONFIG_SYS_FLASH_BASE 0xffe00000
305 #ifdef CONFIG_MONITOR_IS_IN_RAM
306 #define CONFIG_SYS_MONITOR_BASE 0x20000
308 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
311 #define CONFIG_SYS_MONITOR_LEN 0x20000
312 #define CONFIG_SYS_MALLOC_LEN (256 << 10)
313 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
316 * For booting Linux, the board info and command line data
317 * have to be in the first 8 MB of memory, since this is
318 * the maximum mapped by the Linux kernel during initialization ??
320 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
322 /*-----------------------------------------------------------------------
325 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
326 #define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
327 #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */
329 /*-----------------------------------------------------------------------
330 * Cache Configuration
332 #define CONFIG_SYS_CACHELINE_SIZE 16
334 /*-----------------------------------------------------------------------
335 * Memory bank definitions
337 * Please refer also to Motorola Coldfire user manual - Chapter XXX
338 * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf>
340 #define CONFIG_SYS_BR0_PRELIM 0xFFE00201
341 #define CONFIG_SYS_OR0_PRELIM 0xFFE00014
343 #define CONFIG_SYS_BR1_PRELIM 0
344 #define CONFIG_SYS_OR1_PRELIM 0
346 #define CONFIG_SYS_BR2_PRELIM 0
347 #define CONFIG_SYS_OR2_PRELIM 0
349 #define CONFIG_SYS_BR3_PRELIM 0
350 #define CONFIG_SYS_OR3_PRELIM 0
352 #define CONFIG_SYS_BR4_PRELIM 0
353 #define CONFIG_SYS_OR4_PRELIM 0
355 #define CONFIG_SYS_BR5_PRELIM 0
356 #define CONFIG_SYS_OR5_PRELIM 0
358 #define CONFIG_SYS_BR6_PRELIM 0
359 #define CONFIG_SYS_OR6_PRELIM 0
361 #define CONFIG_SYS_BR7_PRELIM 0x00000701
362 #define CONFIG_SYS_OR7_PRELIM 0xFF00007C
364 /*-----------------------------------------------------------------------
367 #define LED_STAT_0 0xffff /*all LEDs off*/
368 #define LED_STAT_1 0xfffe
369 #define LED_STAT_2 0xfffd
370 #define LED_STAT_3 0xfffb
371 #define LED_STAT_4 0xfff7
372 #define LED_STAT_5 0xffef
373 #define LED_STAT_6 0xffdf
374 #define LED_STAT_7 0xff00 /*all LEDs on*/
376 /*-----------------------------------------------------------------------
377 * Port configuration (GPIO)
379 #define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external
381 #define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs
382 (1^=output, 0^=input) */
383 #define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */
384 #define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART
386 #define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */
387 #define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */
388 #define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */
390 #endif /* _CONFIG_COBRA5272_H */