2 * Configuation settings for the Sentec Cobra Board.
4 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
6 * SPDX-License-Identifier: GPL-2.0+
10 * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board
12 * Author: Florian Schlote
14 * For a description of configuration options please refer also to the
15 * general u-boot-1.x.x/README file
20 * board/config.h - configuration options, board specific
24 #ifndef _CONFIG_COBRA5272_H
25 #define _CONFIG_COBRA5272_H
28 * Defines processor clock - important for correct timings concerning serial
33 #define CONFIG_SYS_CLK 66000000
34 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
37 * Enable use of Ethernet
42 /* Enable Dma Timer */
46 * Define baudrate for UART1 (console output, tftp, ...)
47 * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
48 * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command
53 #define CONFIG_MCFUART
54 #define CONFIG_SYS_UART_PORT (0)
55 #define CONFIG_BAUDRATE 19200
58 * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
59 * timeout acc. to your needs
60 * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000
66 #define CONFIG_WATCHDOG
67 #define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */
71 * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different
72 * bootloader residing in flash ('chainloading'); if you want to use
73 * chainloading or want to compile a u-boot binary that can be loaded into
76 * You will need a first stage bootloader then, e. g. colilo or a working BDM
77 * cable (Background Debug Mode)
79 * Setting #if 0: u-boot will start from flash and relocate itself to RAM
81 * Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE
82 * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000)
88 #define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */
92 * Configuration for environment
93 * Environment is embedded in u-boot in the second sector of the flash
97 #ifndef CONFIG_MONITOR_IS_IN_RAM
98 #define CONFIG_ENV_OFFSET 0x4000
99 #define CONFIG_ENV_SECT_SIZE 0x2000
100 #define CONFIG_ENV_IS_IN_FLASH 1
102 #define CONFIG_ENV_ADDR 0xffe04000
103 #define CONFIG_ENV_SECT_SIZE 0x2000
104 #define CONFIG_ENV_IS_IN_FLASH 1
111 #define CONFIG_BOOTP_BOOTFILESIZE
112 #define CONFIG_BOOTP_BOOTPATH
113 #define CONFIG_BOOTP_GATEWAY
114 #define CONFIG_BOOTP_HOSTNAME
118 * Command line configuration.
120 #include <config_cmd_default.h>
122 #define CONFIG_CMD_PING
124 #undef CONFIG_CMD_LOADS
125 #undef CONFIG_CMD_LOADB
126 #undef CONFIG_CMD_MII
129 # define CONFIG_MII 1
130 # define CONFIG_MII_INIT 1
131 # define CONFIG_SYS_DISCOVER_PHY
132 # define CONFIG_SYS_RX_ETH_BUFFER 8
133 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
135 # define CONFIG_SYS_FEC0_PINMUX 0
136 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
137 # define MCFFEC_TOUT_LOOP 50000
138 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
139 # ifndef CONFIG_SYS_DISCOVER_PHY
140 # define FECDUPLEX FULL
141 # define FECSPEED _100BASET
143 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
144 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
146 # endif /* CONFIG_SYS_DISCOVER_PHY */
150 *-----------------------------------------------------------------------------
151 * Define user parameters that have to be customized most likely
152 *-----------------------------------------------------------------------------
155 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/
157 #define CONFIG_BOOTDELAY 5 /* used for autoboot, delay in
158 seconds u-boot will wait before starting defined (auto-)boot command, setting
159 to -1 disables delay, setting to 0 will too prevent access to u-boot command
160 interface: u-boot then has to reflashed */
163 /* The following settings will be contained in the environment block ; if you
164 want to use a neutral environment all those settings can be manually set in
165 u-boot: 'set' command */
169 #define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please
170 enter a valid image address in flash */
172 #define CONFIG_BOOTARGS " " /* default bootargs that are
173 considered during boot */
175 /* User network settings */
177 #define CONFIG_ETHADDR 00:00:00:00:00:09 /* default ethernet MAC addr. */
178 #define CONFIG_IPADDR 192.168.100.2 /* default board IP address */
179 #define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */
183 #define CONFIG_SYS_PROMPT "COBRA > " /* Layout of u-boot prompt*/
185 #define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address
186 from which user programs will be started */
190 #define CONFIG_SYS_LONGHELP /* undef to save memory */
192 #if defined(CONFIG_CMD_KGDB)
193 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
195 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
197 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
198 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
199 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
202 *-----------------------------------------------------------------------------
203 * End of user parameters to be customized
204 *-----------------------------------------------------------------------------
208 * Defines memory range for test
212 #define CONFIG_SYS_MEMTEST_START 0x400
213 #define CONFIG_SYS_MEMTEST_END 0x380000
216 * Low Level Configuration Settings
217 * (address mappings, register initial values, etc.)
218 * You should know what you are doing if you make changes here.
223 * Base register address
227 #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */
230 * System Conf. Reg. & System Protection Reg.
234 #define CONFIG_SYS_SCR 0x0003
235 #define CONFIG_SYS_SPR 0xffff
242 #define CONFIG_SYS_DISCOVER_PHY
243 #define CONFIG_SYS_ENET_BD_BASE 0x780000
245 /*-----------------------------------------------------------------------
246 * Definitions for initial stack pointer and data area (in internal SRAM)
248 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
249 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
250 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
251 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
253 /*-----------------------------------------------------------------------
254 * Start addresses for the final memory configuration
255 * (Set up by the startup code)
256 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
258 #define CONFIG_SYS_SDRAM_BASE 0x00000000
261 *-------------------------------------------------------------------------
262 * RAM SIZE (is defined above)
263 *-----------------------------------------------------------------------
266 /* #define CONFIG_SYS_SDRAM_SIZE 16 */
269 *-----------------------------------------------------------------------
272 #define CONFIG_SYS_FLASH_BASE 0xffe00000
274 #ifdef CONFIG_MONITOR_IS_IN_RAM
275 #define CONFIG_SYS_MONITOR_BASE 0x20000
277 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
280 #define CONFIG_SYS_MONITOR_LEN 0x20000
281 #define CONFIG_SYS_MALLOC_LEN (256 << 10)
282 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
285 * For booting Linux, the board info and command line data
286 * have to be in the first 8 MB of memory, since this is
287 * the maximum mapped by the Linux kernel during initialization ??
289 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
291 /*-----------------------------------------------------------------------
294 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
295 #define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
296 #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */
298 /*-----------------------------------------------------------------------
299 * Cache Configuration
301 #define CONFIG_SYS_CACHELINE_SIZE 16
303 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
304 CONFIG_SYS_INIT_RAM_SIZE - 8)
305 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
306 CONFIG_SYS_INIT_RAM_SIZE - 4)
307 #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI)
308 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
309 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
310 CF_ACR_EN | CF_ACR_SM_ALL)
311 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \
312 CF_CACR_DISD | CF_CACR_INVI | \
313 CF_CACR_CEIB | CF_CACR_DCM | \
316 /*-----------------------------------------------------------------------
317 * Memory bank definitions
319 * Please refer also to Motorola Coldfire user manual - Chapter XXX
320 * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf>
322 #define CONFIG_SYS_BR0_PRELIM 0xFFE00201
323 #define CONFIG_SYS_OR0_PRELIM 0xFFE00014
325 #define CONFIG_SYS_BR1_PRELIM 0
326 #define CONFIG_SYS_OR1_PRELIM 0
328 #define CONFIG_SYS_BR2_PRELIM 0
329 #define CONFIG_SYS_OR2_PRELIM 0
331 #define CONFIG_SYS_BR3_PRELIM 0
332 #define CONFIG_SYS_OR3_PRELIM 0
334 #define CONFIG_SYS_BR4_PRELIM 0
335 #define CONFIG_SYS_OR4_PRELIM 0
337 #define CONFIG_SYS_BR5_PRELIM 0
338 #define CONFIG_SYS_OR5_PRELIM 0
340 #define CONFIG_SYS_BR6_PRELIM 0
341 #define CONFIG_SYS_OR6_PRELIM 0
343 #define CONFIG_SYS_BR7_PRELIM 0x00000701
344 #define CONFIG_SYS_OR7_PRELIM 0xFF00007C
346 /*-----------------------------------------------------------------------
349 #define LED_STAT_0 0xffff /*all LEDs off*/
350 #define LED_STAT_1 0xfffe
351 #define LED_STAT_2 0xfffd
352 #define LED_STAT_3 0xfffb
353 #define LED_STAT_4 0xfff7
354 #define LED_STAT_5 0xffef
355 #define LED_STAT_6 0xffdf
356 #define LED_STAT_7 0xff00 /*all LEDs on*/
358 /*-----------------------------------------------------------------------
359 * Port configuration (GPIO)
361 #define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external
363 #define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs
364 (1^=output, 0^=input) */
365 #define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */
366 #define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART
368 #define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */
369 #define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */
370 #define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */
372 #endif /* _CONFIG_COBRA5272_H */