git.sur5r.net Git - u-boot/blob - include/configs/ls2080ardb.h

   1 /*
   2  * Copyright 2017 NXP
   3  * Copyright 2015 Freescale Semiconductor
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __LS2_RDB_H
   9 #define __LS2_RDB_H
  10
  11 #include "ls2080a_common.h"
  12
  13 #undef CONFIG_CONS_INDEX
  14 #define CONFIG_CONS_INDEX       2
  15
  16 #ifdef CONFIG_FSL_QSPI
  17 #ifdef CONFIG_TARGET_LS2081ARDB
  18 #define CONFIG_QIXIS_I2C_ACCESS
  19 #endif
  20 #define CONFIG_SYS_I2C_EARLY_INIT
  21 #endif
  22
  23 #define I2C_MUX_CH_VOL_MONITOR          0xa
  24 #define I2C_VOL_MONITOR_ADDR            0x38
  25 #define CONFIG_VOL_MONITOR_IR36021_READ
  26 #define CONFIG_VOL_MONITOR_IR36021_SET
  27
  28 #define CONFIG_VID_FLS_ENV              "ls2080ardb_vdd_mv"
  29 #ifndef CONFIG_SPL_BUILD
  30 #define CONFIG_VID
  31 #endif
  32 /* step the IR regulator in 5mV increments */
  33 #define IR_VDD_STEP_DOWN                5
  34 #define IR_VDD_STEP_UP                  5
  35 /* The lowest and highest voltage allowed for LS2080ARDB */
  36 #define VDD_MV_MIN                      819
  37 #define VDD_MV_MAX                      1212
  38
  39 #ifndef __ASSEMBLY__
  40 unsigned long get_board_sys_clk(void);
  41 #endif
  42
  43 #define CONFIG_SYS_CLK_FREQ             get_board_sys_clk()
  44 #define CONFIG_DDR_CLK_FREQ             133333333
  45 #define COUNTER_FREQUENCY_REAL          (CONFIG_SYS_CLK_FREQ/4)
  46
  47 #define CONFIG_DDR_SPD
  48 #define CONFIG_DDR_ECC
  49 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  50 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  51 #define SPD_EEPROM_ADDRESS1     0x51
  52 #define SPD_EEPROM_ADDRESS2     0x52
  53 #define SPD_EEPROM_ADDRESS3     0x53
  54 #define SPD_EEPROM_ADDRESS4     0x54
  55 #define SPD_EEPROM_ADDRESS5     0x55
  56 #define SPD_EEPROM_ADDRESS6     0x56    /* dummy address */
  57 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
  58 #define CONFIG_SYS_SPD_BUS_NUM  0       /* SPD on I2C bus 0 */
  59 #define CONFIG_DIMM_SLOTS_PER_CTLR              2
  60 #define CONFIG_CHIP_SELECTS_PER_CTRL            4
  61 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
  62 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR       1
  63 #endif
  64 #define CONFIG_FSL_DDR_BIST     /* enable built-in memory test */
  65
  66 /* SATA */
  67 #define CONFIG_LIBATA
  68 #define CONFIG_SCSI_AHCI_PLAT
  69
  70 #define CONFIG_SYS_SATA1                        AHCI_BASE_ADDR1
  71 #define CONFIG_SYS_SATA2                        AHCI_BASE_ADDR2
  72
  73 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  74 #define CONFIG_SYS_SCSI_MAX_LUN                 1
  75 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  76                                                 CONFIG_SYS_SCSI_MAX_LUN)
  77
  78 #ifndef CONFIG_FSL_QSPI
  79 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
  80
  81 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
  82 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128*1024*1024)
  83 #define CONFIG_SYS_NOR_AMASK_EARLY      IFC_AMASK(64*1024*1024)
  84
  85 #define CONFIG_SYS_NOR0_CSPR                                    \
  86         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)             | \
  87         CSPR_PORT_SIZE_16                                       | \
  88         CSPR_MSEL_NOR                                           | \
  89         CSPR_V)
  90 #define CONFIG_SYS_NOR0_CSPR_EARLY                              \
  91         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)       | \
  92         CSPR_PORT_SIZE_16                                       | \
  93         CSPR_MSEL_NOR                                           | \
  94         CSPR_V)
  95 #define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(12)
  96 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
  97                                 FTIM0_NOR_TEADC(0x5) | \
  98                                 FTIM0_NOR_TEAHC(0x5))
  99 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 100                                 FTIM1_NOR_TRAD_NOR(0x1a) |\
 101                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 102 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 103                                 FTIM2_NOR_TCH(0x4) | \
 104                                 FTIM2_NOR_TWPH(0x0E) | \
 105                                 FTIM2_NOR_TWP(0x1c))
 106 #define CONFIG_SYS_NOR_FTIM3    0x04000000
 107 #define CONFIG_SYS_IFC_CCR      0x01000000
 108
 109 #ifdef CONFIG_MTD_NOR_FLASH
 110 #define CONFIG_FLASH_CFI_DRIVER
 111 #define CONFIG_SYS_FLASH_CFI
 112 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 113 #define CONFIG_SYS_FLASH_QUIET_TEST
 114 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 115
 116 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 117 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 118 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 119 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 120
 121 #define CONFIG_SYS_FLASH_EMPTY_INFO
 122 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE,\
 123                                          CONFIG_SYS_FLASH_BASE + 0x40000000}
 124 #endif
 125
 126 #define CONFIG_NAND_FSL_IFC
 127 #define CONFIG_SYS_NAND_MAX_ECCPOS      256
 128 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 129
 130 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
 131 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 132                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 133                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 134                                 | CSPR_V)
 135 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)
 136
 137 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 138                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 139                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 140                                 | CSOR_NAND_RAL_3       /* RAL = 3Byes */ \
 141                                 | CSOR_NAND_PGS_4K      /* Page Size = 4K */ \
 142                                 | CSOR_NAND_SPRZ_224    /* Spare size = 224 */ \
 143                                 | CSOR_NAND_PB(128))    /* Pages Per Block 128*/
 144
 145 #define CONFIG_SYS_NAND_ONFI_DETECTION
 146
 147 /* ONFI NAND Flash mode0 Timing Params */
 148 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x0e) | \
 149                                         FTIM0_NAND_TWP(0x30)   | \
 150                                         FTIM0_NAND_TWCHT(0x0e) | \
 151                                         FTIM0_NAND_TWH(0x14))
 152 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x64) | \
 153                                         FTIM1_NAND_TWBE(0xab)  | \
 154                                         FTIM1_NAND_TRR(0x1c)   | \
 155                                         FTIM1_NAND_TRP(0x30))
 156 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x1e) | \
 157                                         FTIM2_NAND_TREH(0x14) | \
 158                                         FTIM2_NAND_TWHRE(0x3c))
 159 #define CONFIG_SYS_NAND_FTIM3           0x0
 160
 161 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 162 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 163 #define CONFIG_MTD_NAND_VERIFY_WRITE
 164
 165 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 166 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 167 #define QIXIS_LBMAP_SWITCH              0x06
 168 #define QIXIS_LBMAP_MASK                0x0f
 169 #define QIXIS_LBMAP_SHIFT               0
 170 #define QIXIS_LBMAP_DFLTBANK            0x00
 171 #define QIXIS_LBMAP_ALTBANK             0x04
 172 #define QIXIS_LBMAP_NAND                0x09
 173 #define QIXIS_RST_CTL_RESET             0x31
 174 #define QIXIS_RST_CTL_RESET_EN          0x30
 175 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 176 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 177 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 178 #define QIXIS_RCW_SRC_NAND              0x119
 179 #define QIXIS_RST_FORCE_MEM             0x01
 180
 181 #define CONFIG_SYS_CSPR3_EXT    (0x0)
 182 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
 183                                 | CSPR_PORT_SIZE_8 \
 184                                 | CSPR_MSEL_GPCM \
 185                                 | CSPR_V)
 186 #define CONFIG_SYS_CSPR3_FINAL  (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 187                                 | CSPR_PORT_SIZE_8 \
 188                                 | CSPR_MSEL_GPCM \
 189                                 | CSPR_V)
 190
 191 #define CONFIG_SYS_AMASK3       IFC_AMASK(64*1024)
 192 #define CONFIG_SYS_CSOR3        CSOR_GPCM_ADM_SHIFT(12)
 193 /* QIXIS Timing parameters for IFC CS3 */
 194 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 195                                         FTIM0_GPCM_TEADC(0x0e) | \
 196                                         FTIM0_GPCM_TEAHC(0x0e))
 197 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0xff) | \
 198                                         FTIM1_GPCM_TRAD(0x3f))
 199 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0xf) | \
 200                                         FTIM2_GPCM_TCH(0xf) | \
 201                                         FTIM2_GPCM_TWP(0x3E))
 202 #define CONFIG_SYS_CS3_FTIM3            0x0
 203
 204 #if defined(CONFIG_SPL) && defined(CONFIG_NAND)
 205 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 206 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR0_CSPR_EARLY
 207 #define CONFIG_SYS_CSPR2_FINAL          CONFIG_SYS_NOR0_CSPR
 208 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 209 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 210 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 211 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 212 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 213 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 214 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 215 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 216 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 217 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 218 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 219 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 220 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 221 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 222
 223 #define CONFIG_ENV_OFFSET               (2048 * 1024)
 224 #define CONFIG_ENV_SECT_SIZE            0x20000
 225 #define CONFIG_ENV_SIZE                 0x2000
 226 #define CONFIG_SPL_PAD_TO               0x80000
 227 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (1024 * 1024)
 228 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (512 * 1024)
 229 #else
 230 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 231 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR_EARLY
 232 #define CONFIG_SYS_CSPR0_FINAL          CONFIG_SYS_NOR0_CSPR
 233 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 234 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 235 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 236 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 237 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 238 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 239 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 240 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 241 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 242 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 243 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 244 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 245 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 246 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 247
 248 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x300000)
 249 #define CONFIG_ENV_SECT_SIZE            0x20000
 250 #define CONFIG_ENV_SIZE                 0x2000
 251 #endif
 252
 253 /* Debug Server firmware */
 254 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
 255 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
 256 #endif
 257 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
 258
 259 #ifdef CONFIG_TARGET_LS2081ARDB
 260 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 261 #define QIXIS_QMAP_MASK                 0x07
 262 #define QIXIS_QMAP_SHIFT                5
 263 #define QIXIS_LBMAP_DFLTBANK            0x00
 264 #define QIXIS_LBMAP_QSPI                0x00
 265 #define QIXIS_RCW_SRC_QSPI              0x62
 266 #define QIXIS_LBMAP_ALTBANK             0x20
 267 #define QIXIS_RST_CTL_RESET             0x31
 268 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 269 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 270 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 271 #define QIXIS_LBMAP_MASK                0x0f
 272 #define QIXIS_RST_CTL_RESET_EN          0x30
 273 #endif
 274
 275 /*
 276  * I2C
 277  */
 278 #ifdef CONFIG_TARGET_LS2081ARDB
 279 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
 280 #endif
 281 #define I2C_MUX_PCA_ADDR                0x75
 282 #define I2C_MUX_PCA_ADDR_PRI            0x75 /* Primary Mux*/
 283
 284 /* I2C bus multiplexer */
 285 #define I2C_MUX_CH_DEFAULT      0x8
 286
 287 /* SPI */
 288 #if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI)
 289 #define CONFIG_SPI_FLASH
 290 #ifdef CONFIG_FSL_DSPI
 291 #define CONFIG_SPI_FLASH_STMICRO
 292 #endif
 293 #ifdef CONFIG_FSL_QSPI
 294 #define CONFIG_SPI_FLASH_SPANSION
 295 #endif
 296 #define FSL_QSPI_FLASH_SIZE             SZ_64M  /* 64MB */
 297 #define FSL_QSPI_FLASH_NUM              2
 298 #endif
 299
 300 /*
 301  * RTC configuration
 302  */
 303 #define RTC
 304 #ifdef CONFIG_TARGET_LS2081ARDB
 305 #define CONFIG_RTC_PCF8563              1
 306 #define CONFIG_SYS_I2C_RTC_ADDR         0x51
 307 #else
 308 #define CONFIG_RTC_DS3231               1
 309 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 310 #endif
 311
 312 /* EEPROM */
 313 #define CONFIG_ID_EEPROM
 314 #define CONFIG_SYS_I2C_EEPROM_NXID
 315 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 316 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 317 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 318 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 319 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 320
 321 #define CONFIG_FSL_MEMAC
 322
 323 #ifdef CONFIG_PCI
 324 #define CONFIG_PCI_SCAN_SHOW
 325 #endif
 326
 327 /*  MMC  */
 328 #ifdef CONFIG_MMC
 329 #define CONFIG_FSL_ESDHC
 330 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 331 #endif
 332
 333 #define CONFIG_MISC_INIT_R
 334
 335 #undef CONFIG_CMDLINE_EDITING
 336 #include <config_distro_defaults.h>
 337
 338 #define BOOT_TARGET_DEVICES(func) \
 339         func(USB, usb, 0) \
 340         func(MMC, mmc, 0) \
 341         func(SCSI, scsi, 0) \
 342         func(DHCP, dhcp, na)
 343 #include <config_distro_bootcmd.h>
 344
 345 #ifdef CONFIG_QSPI_BOOT
 346 #define MC_INIT_CMD                             \
 347         "mcinitcmd=env exists secureboot && "   \
 348         "esbc_validate 0x20700000 && "          \
 349         "esbc_validate 0x20740000;"             \
 350         "fsl_mc start mc 0x20a00000 0x20e00000 \0"
 351 #elif defined(CONFIG_SD_BOOT)
 352 #define MC_INIT_CMD                             \
 353         "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
 354         "mmc read 0x80100000 0x7000 0x800;"     \
 355         "env exists secureboot && "             \
 356         "mmc read 0x80700000 0x3800 0x10 && "   \
 357         "mmc read 0x80740000 0x3A00 0x10 && "   \
 358         "esbc_validate 0x80700000 && "          \
 359         "esbc_validate 0x80740000 ;"            \
 360         "fsl_mc start mc 0x80000000 0x80100000\0" \
 361         "mcmemsize=0x70000000\0"
 362 #else
 363 #define MC_INIT_CMD                             \
 364         "mcinitcmd=env exists secureboot && "   \
 365         "esbc_validate 0x580700000 && "         \
 366         "esbc_validate 0x580740000; "           \
 367         "fsl_mc start mc 0x580a00000 0x580e00000 \0"
 368 #endif
 369
 370 /* Initial environment variables */
 371 #undef CONFIG_EXTRA_ENV_SETTINGS
 372 #define CONFIG_EXTRA_ENV_SETTINGS               \
 373         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 374         "ramdisk_addr=0x800000\0"               \
 375         "ramdisk_size=0x2000000\0"              \
 376         "fdt_high=0xa0000000\0"                 \
 377         "initrd_high=0xffffffffffffffff\0"      \
 378         "fdt_addr=0x64f00000\0"                 \
 379         "kernel_addr=0x65000000\0"              \
 380         "kernel_start=0x1000000\0"              \
 381         "kernelheader_start=0x800000\0"         \
 382         "scriptaddr=0x80000000\0"               \
 383         "scripthdraddr=0x80080000\0"            \
 384         "fdtheader_addr_r=0x80100000\0"         \
 385         "kernelheader_addr_r=0x80200000\0"      \
 386         "kernelheader_addr=0x580800000\0"       \
 387         "kernel_addr_r=0x81000000\0"            \
 388         "kernelheader_size=0x40000\0"           \
 389         "fdt_addr_r=0x90000000\0"               \
 390         "load_addr=0xa0000000\0"                \
 391         "kernel_size=0x2800000\0"               \
 392         "kernel_addr_sd=0x8000\0"               \
 393         "kernel_size_sd=0x14000\0"              \
 394         "console=ttyAMA0,38400n8\0"             \
 395         "mcmemsize=0x70000000\0"                \
 396         "sd_bootcmd=echo Trying load from SD ..;" \
 397         "mmcinfo; mmc read $load_addr "         \
 398         "$kernel_addr_sd $kernel_size_sd && "   \
 399         "bootm $load_addr#$board\0"             \
 400         MC_INIT_CMD                             \
 401         BOOTENV                                 \
 402         "boot_scripts=ls2088ardb_boot.scr\0"    \
 403         "boot_script_hdr=hdr_ls2088ardb_bs.out\0"       \
 404         "scan_dev_for_boot_part="               \
 405                 "part list ${devtype} ${devnum} devplist; "     \
 406                 "env exists devplist || setenv devplist 1; "    \
 407                 "for distro_bootpart in ${devplist}; do "       \
 408                         "if fstype ${devtype} "                 \
 409                                 "${devnum}:${distro_bootpart} " \
 410                                 "bootfstype; then "             \
 411                                 "run scan_dev_for_boot; "       \
 412                         "fi; "                                  \
 413                 "done\0"                                        \
 414         "scan_dev_for_boot="                                    \
 415                 "echo Scanning ${devtype} "                     \
 416                         "${devnum}:${distro_bootpart}...; "     \
 417                 "for prefix in ${boot_prefixes}; do "           \
 418                         "run scan_dev_for_scripts; "            \
 419                 "done;\0"                                       \
 420         "boot_a_script="                                        \
 421                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 422                         "${scriptaddr} ${prefix}${script}; "    \
 423                 "env exists secureboot && load ${devtype} "     \
 424                         "${devnum}:${distro_bootpart} "         \
 425                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 426                         "&& esbc_validate ${scripthdraddr};"    \
 427                 "source ${scriptaddr}\0"                        \
 428         "qspi_bootcmd=echo Trying load from qspi..;"            \
 429                 "sf probe && sf read $load_addr "               \
 430                 "$kernel_start $kernel_size ; env exists secureboot &&" \
 431                 "sf read $kernelheader_addr_r $kernelheader_start "     \
 432                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 433                 " bootm $load_addr#$board\0"                    \
 434         "nor_bootcmd=echo Trying load from nor..;"              \
 435                 "cp.b $kernel_addr $load_addr "                 \
 436                 "$kernel_size ; env exists secureboot && "      \
 437                 "cp.b $kernelheader_addr $kernelheader_addr_r " \
 438                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 439                 "bootm $load_addr#$board\0"
 440
 441 #undef CONFIG_BOOTCOMMAND
 442 #ifdef CONFIG_QSPI_BOOT
 443 /* Try to boot an on-QSPI kernel first, then do normal distro boot */
 444 #define CONFIG_BOOTCOMMAND                                              \
 445                         "env exists mcinitcmd && env exists secureboot "\
 446                         "&& esbc_validate 0x20780000; "                 \
 447                         "env exists mcinitcmd && "                      \
 448                         "fsl_mc lazyapply dpl 0x20d00000; "             \
 449                         "run distro_bootcmd;env exists secureboot "     \
 450                         " && esbc_halt;run qspi_bootcmd; "
 451 #elif defined(CONFIG_SD_BOOT)
 452 /* Try to boot an on-SD kernel first, then do normal distro boot */
 453 #define CONFIG_BOOTCOMMAND                                              \
 454                         "env exists mcinitcmd && env exists secureboot "\
 455                         "&& mmcinfo && mmc read $load_addr 0x3c00 0x800 " \
 456                         "&& esbc_validate $load_addr; "                 \
 457                         "env exists mcinitcmd && run mcinitcmd "        \
 458                         "&& mmc read 0x88000000 0x6800 0x800 "          \
 459                         "&& fsl_mc lazyapply dpl 0x88000000; "          \
 460                         "run distro_bootcmd;env exists secureboot "     \
 461                         "&& esbc_halt;run sd_bootcmd;"
 462 #else
 463 /* Try to boot an on-NOR kernel first, then do normal distro boot */
 464 #define CONFIG_BOOTCOMMAND                                              \
 465                         "env exists mcinitcmd && env exists secureboot "\
 466                         "&& esbc_validate 0x580780000; env exists mcinitcmd "\
 467                         "&& fsl_mc lazyapply dpl 0x580d00000;"          \
 468                         "run distro_bootcmd; env exists secureboot "    \
 469                         "&& esbc_halt; run nor_bootcmd;"
 470 #endif
 471
 472 /* MAC/PHY configuration */
 473 #ifdef CONFIG_FSL_MC_ENET
 474 #define CONFIG_PHYLIB_10G
 475 #define CONFIG_PHY_AQUANTIA
 476 #define CONFIG_PHY_CORTINA
 477 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 478 #ifdef CONFIG_QSPI_BOOT
 479 #define CONFIG_CORTINA_FW_ADDR          0x20980000
 480 #else
 481 #define CONFIG_CORTINA_FW_ADDR          0x580980000
 482 #endif
 483 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 484
 485 #define CORTINA_PHY_ADDR1       0x10
 486 #define CORTINA_PHY_ADDR2       0x11
 487 #define CORTINA_PHY_ADDR3       0x12
 488 #define CORTINA_PHY_ADDR4       0x13
 489 #define AQ_PHY_ADDR1            0x00
 490 #define AQ_PHY_ADDR2            0x01
 491 #define AQ_PHY_ADDR3            0x02
 492 #define AQ_PHY_ADDR4            0x03
 493 #define AQR405_IRQ_MASK         0x36
 494
 495 #define CONFIG_MII
 496 #define CONFIG_ETHPRIME         "DPMAC1@xgmii"
 497 #define CONFIG_PHY_AQUANTIA
 498 #endif
 499
 500 #include <asm/fsl_secure_boot.h>
 501
 502 #endif /* __LS2_RDB_H */