1 /* SPDX-License-Identifier: GPL-2.0+ */
4 * Net Insight <www.netinsight.net>
5 * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
7 * Based on sheevaplug.h:
9 * Marvell Semiconductor <www.marvell.com>
10 * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
13 #ifndef _CONFIG_OPENRD_H
14 #define _CONFIG_OPENRD_H
17 * High Level Configuration Options (easy to change)
19 #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
20 #define CONFIG_KW88F6281 1 /* SOC Name */
21 #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
24 * Commands configuration
26 #define CONFIG_SYS_MVFS
29 * mv-common.h should be defined after CMD configs since it used them
30 * to enable certain macros
32 #include "mv-common.h"
35 * Environment variables configurations
37 #ifdef CONFIG_CMD_NAND
38 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
41 * max 4k env size is enough, but in case of nand
42 * it has to be rounded to sector size
44 #define CONFIG_ENV_SIZE 0x20000 /* 128k */
45 #define CONFIG_ENV_ADDR 0x60000
46 #define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
48 * Environment is right behind U-Boot in flash. Make sure U-Boot
49 * doesn't grow into the environment area.
51 #define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET
54 * Default environment variables
56 #define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
57 "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
58 "${x_bootcmd_usb}; bootm 0x6400000;"
60 #define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console=ttyS0,115200 " \
61 CONFIG_MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
62 "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
63 "x_bootcmd_usb=usb start\0" \
64 "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
65 "mtdids="CONFIG_MTDIDS_DEFAULT"\0" \
66 "mtdparts="CONFIG_MTDPARTS_DEFAULT"\0"
69 * Ethernet Driver configuration
72 # ifdef CONFIG_BOARD_IS_OPENRD_BASE
73 # define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
75 # define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */
77 # ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE
78 # define CONFIG_PHY_BASE_ADR 0x0
79 # define PHY_NO "88E1121"
81 # define CONFIG_PHY_BASE_ADR 0x8
82 # define PHY_NO "88E1116"
84 #endif /* CONFIG_CMD_NET */
87 * SATA Driver configuration
89 #ifdef CONFIG_MVSATA_IDE
90 #define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
91 #define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
92 #endif /*CONFIG_MVSATA_IDE*/
95 #define CONFIG_MVEBU_MMC
96 #define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
97 #endif /* CONFIG_CMD_MMC */
99 #endif /* _CONFIG_OPENRD_BASE_H */