2 * Copyright (C) 2003 ETC s.r.o.
4 * This program is free software; you can redistribute it and/or
5 * modify it under the terms of the GNU General Public License as
6 * published by the Free Software Foundation; either version 2 of
7 * the License, or (at your option) any later version.
9 * This program is distributed in the hope that it will be useful,
10 * but WITHOUT ANY WARRANTY; without even the implied warranty of
11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
12 * GNU General Public License for more details.
14 * You should have received a copy of the GNU General Public License
15 * along with this program; if not, write to the Free Software
16 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
19 * Written by Peter Figuli <peposh@etc.sk>, 2003.
21 * 2003/13/06 Initial MP10 Support copied from wepep250
27 #define CONFIG_ARM920T 1 /* this is an ARM920T CPU */
28 #define CONFIG_IMX 1 /* in a Motorola MC9328MXL Chip */
29 #define CONFIG_SCB9328 1 /* on a scb9328tronix board */
30 #undef CONFIG_USE_IRQ /* don't need use IRQ/FIQ */
32 #define CONFIG_IMX_SERIAL
33 #define CONFIG_IMX_SERIAL1
35 * Select serial console configuration
41 #define CONFIG_BOOTP_BOOTFILESIZE
42 #define CONFIG_BOOTP_BOOTPATH
43 #define CONFIG_BOOTP_GATEWAY
44 #define CONFIG_BOOTP_HOSTNAME
47 * Command line configuration.
49 #include <config_cmd_default.h>
51 #define CONFIG_CMD_NET
52 #define CONFIG_CMD_PING
53 #define CONFIG_CMD_DHCP
55 #undef CONFIG_CMD_CONSOLE
56 #undef CONFIG_CMD_LOADS
57 #undef CONFIG_CMD_SOURCE
60 * Boot options. Setting delay to -1 stops autostart count down.
61 * NOTE: Sending parameters to kernel depends on kernel version and
62 * 2.4.19-rmk6-pxa1 patch used while my u-boot coding didn't accept
63 * parameters at all! Do not get confused by them so.
65 #define CONFIG_BOOTDELAY -1
66 #define CONFIG_BOOTARGS "console=ttySMX0,115200n8 root=/dev/mtdblock3 rootfstype=jffs2 mtdparts=scb9328_flash:128k(U-boot)ro,128k(U-boot_env),1m(kernel),4m(root),4m(fs) eval_board=evk9328"
67 #define CONFIG_BOOTCOMMAND "bootm 10040000"
68 #define CONFIG_SHOW_BOOT_PROGRESS
69 #define CONFIG_ETHADDR 80:81:82:83:84:85
70 #define CONFIG_NETMASK 255.255.255.0
71 #define CONFIG_IPADDR 10.10.10.9
72 #define CONFIG_SERVERIP 10.10.10.10
75 * General options for u-boot. Modify to save memory foot print
77 #define CONFIG_SYS_LONGHELP /* undef saves memory */
78 #define CONFIG_SYS_PROMPT "scb9328> " /* prompt string */
79 #define CONFIG_SYS_CBSIZE 256 /* console I/O buffer */
80 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* print buffer size */
81 #define CONFIG_SYS_MAXARGS 16 /* max command args */
82 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* boot args buf size */
84 #define CONFIG_SYS_MEMTEST_START 0x08100000 /* memtest test area */
85 #define CONFIG_SYS_MEMTEST_END 0x08F00000
87 #define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
88 #define CONFIG_SYS_CPUSPEED 0x141 /* core clock - register value */
90 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
91 #define CONFIG_BAUDRATE 115200
93 * Definitions related to passing arguments to kernel.
95 #define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */
96 #define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */
97 #define CONFIG_INITRD_TAG 1 /* send initrd params */
100 * Malloc pool need to host env + 128 Kb reserve for other allocations.
102 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128<<10) )
104 #define CONFIG_STACKSIZE (120<<10) /* stack size */
106 #ifdef CONFIG_USE_IRQ
107 #define CONFIG_STACKSIZE_IRQ (4<<10) /* IRQ stack */
108 #define CONFIG_STACKSIZE_FIQ (4<<10) /* FIQ stack */
111 /* SDRAM Setup Values
112 0x910a8300 Precharge Command CAS 3
113 0x910a8200 Precharge Command CAS 2
115 0xa10a8300 AutoRefresh Command CAS 3
116 0xa10a8200 Set AutoRefresh Command CAS 2 */
118 #define PRECHARGE_CMD 0x910a8200
119 #define AUTOREFRESH_CMD 0xa10a8200
125 #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SDRAM */
126 #define SCB9328_SDRAM_1 0x08000000 /* SDRAM bank #1 */
127 #define SCB9328_SDRAM_1_SIZE 0x01000000 /* 16 MB */
129 #define CONFIG_SYS_TEXT_BASE 0x10000000
131 #define CONFIG_SYS_SDRAM_BASE SCB9328_SDRAM_1
132 #define CONFIG_SYS_INIT_SP_ADDR (SCB9328_SDRAM_1 + 0xf00000)
135 * Configuration for FLASH memory for the Synertronixx board
138 /* #define SCB9328_FLASH_32M */
141 #ifdef SCB9328_FLASH_32M
142 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
143 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */
144 #define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */
145 #define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */
146 #define SCB9328_FLASH_BANK_SIZE 0x02000000 /* size of one flash bank */
147 #define SCB9328_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */
148 #define SCB9328_FLASH_BASE 0x10000000 /* location of flash memory */
149 #define SCB9328_FLASH_UNLOCK 1 /* perform hw unlock first */
153 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
154 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* number of sector in FLASH bank */
155 #define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */
156 #define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */
157 #define SCB9328_FLASH_BANK_SIZE 0x01000000 /* size of one flash bank */
158 #define SCB9328_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */
159 #define SCB9328_FLASH_BASE 0x10000000 /* location of flash memory */
160 #define SCB9328_FLASH_UNLOCK 1 /* perform hw unlock first */
161 #endif /* SCB9328_FLASH_32M */
163 /* This should be defined if CFI FLASH device is present. Actually benefit
164 is not so clear to me. In other words we can provide more informations
165 to user, but this expects more complex flash handling we do not provide
167 #undef CONFIG_SYS_FLASH_CFI
169 #define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* timeout for Erase operation */
170 #define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* timeout for Write operation */
172 #define CONFIG_SYS_FLASH_BASE SCB9328_FLASH_BASE
175 * This is setting for JFFS2 support in u-boot.
176 * Right now there is no gain for user, but later on booting kernel might be
177 * possible. Consider using XIP kernel running from flash to save RAM
179 * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
181 #define CONFIG_SYS_JFFS2_FIRST_BANK 0
182 #define CONFIG_SYS_JFFS2_FIRST_SECTOR 5
183 #define CONFIG_SYS_JFFS2_NUM_BANKS 1
186 * Environment setup. Definitions of monitor location and size with
187 * definition of environment setup ends up in 2 possibilities.
188 * 1. Embeded environment - in u-boot code is space for environment
189 * 2. Environment is read from predefined sector of flash
190 * Right now we support 2. possiblity, but expecting no env placed
191 * on mentioned address right now. This also needs to provide whole
192 * sector for it - for us 256Kb is really waste of memory. U-boot uses
193 * default env. and until kernel parameters could be sent to kernel
194 * env. has no sense to us.
197 /* Setup for PA23 which is Reset Default PA23 but has to become
200 #define CONFIG_SYS_GPR_A_VAL 0x00800000
201 #define CONFIG_SYS_GIUS_A_VAL 0x0043fffe
203 #define CONFIG_SYS_MONITOR_BASE 0x10000000
204 #define CONFIG_SYS_MONITOR_LEN 0x20000 /* 128b ( 1 flash sector ) */
205 #define CONFIG_ENV_IS_IN_FLASH 1
206 #define CONFIG_ENV_ADDR 0x10020000 /* absolute address for now */
207 #define CONFIG_ENV_SIZE 0x20000
209 #define CONFIG_ENV_OVERWRITE 1 /* env is not writable now */
213 * 63| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x|32
214 * |DTACK_SEL|0|BCD | BCS | PSZ|PME|SYNC| DOL | CNC| WSC | 0| WWS | EDC |
217 * 31| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x| 0
218 * | OEA | OEN | WEA | WEN | CSA |EBC| DSZ | 0|SP|0|WP| 0 0|PA|CSEN|
221 #define CONFIG_SYS_CS0U_VAL 0x000F2000
222 #define CONFIG_SYS_CS0L_VAL 0x11110d01
223 #define CONFIG_SYS_CS1U_VAL 0x000F0a00
224 #define CONFIG_SYS_CS1L_VAL 0x11110601
225 #define CONFIG_SYS_CS2U_VAL 0x0
226 #define CONFIG_SYS_CS2L_VAL 0x0
228 #define CONFIG_SYS_CS3U_VAL 0x000FFFFF
229 #define CONFIG_SYS_CS3L_VAL 0x00000303
231 #define CONFIG_SYS_CS4U_VAL 0x000F0a00
232 #define CONFIG_SYS_CS4L_VAL 0x11110301
235 #define CONFIG_SYS_CS5U_VAL 0x0000C210 */
237 /* #define CONFIG_SYS_CS5U_VAL 0x00008400
238 mal laenger mahcen, ob der bei 150MHz laenger haelt dann und
239 kaum langsamer ist */
240 /* #define CONFIG_SYS_CS5U_VAL 0x00009400
241 #define CONFIG_SYS_CS5L_VAL 0x11010D03 */
243 #define CONFIG_SYS_CS5U_VAL 0x00008400
244 #define CONFIG_SYS_CS5L_VAL 0x00000D03
246 #define CONFIG_DRIVER_DM9000 1
247 #define CONFIG_DM9000_BASE 0x16000000
248 #define DM9000_IO CONFIG_DM9000_BASE
249 #define DM9000_DATA (CONFIG_DM9000_BASE+4)
251 /* f_{dpll}=2*f{ref}*(MFI+MFN/(MFD+1))/(PD+1)
254 0x002a141f: 191,9944MHz
261 0x08001800: 64MHz mit 16er Quarz
262 0x04001800: 96MHz mit 16er Quarz
263 0x04002400: 144MHz mit 16er Quarz
265 31 |x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x| 0
266 |XXX|--PD---|-------MFD---------|XXX|--MFI--|-----MFN-----------| */
271 #define CONFIG_SYS_MPCTL0_VAL 0x00321431
273 #define CONFIG_SYS_MPCTL0_VAL 0x040e200e
280 #define CONFIG_SYS_SPCTL0_VAL 0x04002400
284 #define CONFIG_SYS_SPCTL0_VAL 0x04001800
288 #define CONFIG_SYS_SPCTL0_VAL 0x08001800
291 /* Das ist der BCLK Divider, der aus der System PLL
292 BCLK und HCLK erzeugt:
293 31 | xxxx xxxx xxxx xxxx xx10 11xx xxxx xxxx | 0
294 0x2f008403 : 192MHz/2=96MHz, 144MHz/2=72MHz PRESC=1->BCLKDIV=2
295 0x2f008803 : 192MHz/3=64MHz, 240MHz/3=80MHz PRESC=1->BCLKDIV=2
296 0x2f001003 : 192MHz/5=38,4MHz
299 Bit 21: MPLL Restart */
302 #define CONFIG_SYS_CSCR_VAL 0x2f030003
306 #define CONFIG_SYS_CSCR_VAL 0x2f030403
310 * Well this has to be defined, but on the other hand it is used differently
311 * one may expect. For instance loadb command do not cares :-)
312 * So advice is - do not relay on this...
314 #define CONFIG_SYS_LOAD_ADDR 0x08400000
316 #define MHZ16QUARZINUSE
318 #ifdef MHZ16QUARZINUSE
319 #define CONFIG_SYSPLL_CLK_FREQ 16000000
321 #define CONFIG_SYSPLL_CLK_FREQ 16780000
324 #define CONFIG_SYS_CLK_FREQ 16780000
326 /* FMCR Bit 0 becomes 0 to make CS3 CS3 :P */
327 #define CONFIG_SYS_FMCR_VAL 0x00000001
329 /* Bit[0:3] contain PERCLK1DIV for UART 1
330 0x000b00b ->b<- -> 192MHz/12=16MHz
331 0x000b00b ->8<- -> 144MHz/09=16MHz
332 0x000b00b ->3<- -> 64MHz/4=16MHz */
335 #define CONFIG_SYS_PCDR_VAL 0x000b00b5
339 #define CONFIG_SYS_PCDR_VAL 0x000b00b3
343 #define CONFIG_SYS_PCDR_VAL 0x000b00b8
346 #endif /* __CONFIG_H */