3 * Stefan Roese, DENX Software Engineering, sr@denx.de.
6 * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
7 * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
9 * This program is free software; you can redistribute it and/or
10 * modify it under the terms of the GNU General Public License as
11 * published by the Free Software Foundation; either version 2 of
12 * the License, or (at your option) any later version.
14 * This program is distributed in the hope that it will be useful,
15 * but WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17 * GNU General Public License for more details.
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software
21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
25 /************************************************************************
26 * sequoia.h - configuration for Sequoia board (PowerPC440EPx)
27 ***********************************************************************/
31 /*-----------------------------------------------------------------------
32 * High Level Configuration Options
33 *----------------------------------------------------------------------*/
34 /* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */
35 #ifndef CONFIG_RAINIER
36 #define CONFIG_SEQUOIA 1 /* Board is Sequoia */
37 #define CONFIG_440EPX 1 /* Specific PPC440EPx */
39 #define CONFIG_440GRX 1 /* Specific PPC440GRx */
41 #define CONFIG_4xx 1 /* ... PPC4xx family */
42 #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
44 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
45 #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
47 /*-----------------------------------------------------------------------
48 * Base addresses -- Note these are effective addresses where the
49 * actual resources get mapped (not physical addresses)
50 *----------------------------------------------------------------------*/
51 #define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
52 #define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
54 #define CFG_BOOT_BASE_ADDR 0xf0000000
55 #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
56 #define CFG_FLASH_BASE 0xfe000000 /* start of FLASH */
57 #define CFG_MONITOR_BASE TEXT_BASE
58 #define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */
59 #define CFG_OCM_BASE 0xe0010000 /* ocm */
60 #define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
61 #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
62 #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
63 #define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
64 #define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
66 /* Don't change either of these */
67 #define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
69 #define CFG_USB2D0_BASE 0xe0000100
70 #define CFG_USB_DEVICE 0xe0000000
71 #define CFG_USB_HOST 0xe0000400
72 #define CFG_BCSR_BASE 0xc0000000
74 /*-----------------------------------------------------------------------
75 * Initial RAM & stack pointer
76 *----------------------------------------------------------------------*/
77 /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
78 #define CFG_INIT_RAM_OCM 1 /* OCM as init ram */
79 #define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
81 #define CFG_INIT_RAM_END (4 << 10)
82 #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
83 #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
84 #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
86 /*-----------------------------------------------------------------------
88 *----------------------------------------------------------------------*/
89 #define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
90 #define CONFIG_BAUDRATE 115200
91 #define CONFIG_SERIAL_MULTI 1
92 /* define this if you want console on UART1 */
93 #undef CONFIG_UART1_CONSOLE
95 #define CFG_BAUDRATE_TABLE \
96 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
98 /*-----------------------------------------------------------------------
100 *----------------------------------------------------------------------*/
101 #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
102 #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
104 #define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
107 /*-----------------------------------------------------------------------
109 *----------------------------------------------------------------------*/
110 #define CFG_FLASH_CFI /* The flash is CFI compatible */
111 #define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
113 #define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
115 #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
116 #define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
118 #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
119 #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
121 #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
122 #define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
124 #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
125 #define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
127 #ifdef CFG_ENV_IS_IN_FLASH
128 #define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
129 #define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
130 #define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
132 /* Address and size of Redundant Environment Sector */
133 #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
134 #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
137 /*-----------------------------------------------------------------------
139 *----------------------------------------------------------------------*/
140 #define CFG_MAX_NAND_DEVICE 1
141 #define NAND_MAX_CHIPS 1
142 #define CFG_NAND_BASE CFG_NAND_ADDR
145 * IPL (Initial Program Loader, integrated inside CPU)
146 * Will load first 4k from NAND (SPL) into cache and execute it from there.
148 * SPL (Secondary Program Loader)
149 * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
150 * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
151 * controller and the NAND controller so that the special U-Boot image can be
152 * loaded from NAND to SDRAM.
155 * This NAND U-Boot (NUB) is a special U-Boot version which can be started
156 * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
158 * On 440EPx the SPL is copied to SDRAM before the NAND controller is
159 * set up. While still running from cache, I experienced problems accessing
160 * the NAND controller. sr - 2006-08-25
162 #define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
163 #define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
164 #define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */
165 #define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
166 #define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
167 #define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
170 * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
172 #define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
173 #define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
176 * Now the NAND chip has to be defined (no autodetection used!)
178 #define CFG_NAND_PAGE_SIZE (512) /* NAND chip page size */
179 #define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
180 #define CFG_NAND_PAGE_COUNT (32) /* NAND chip page count */
181 #define CFG_NAND_BAD_BLOCK_POS (5) /* Location of bad block marker */
182 #undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
184 #ifdef CFG_ENV_IS_IN_NAND
186 * For NAND booting the environment is embedded in the U-Boot image. Please take
187 * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
189 #define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
190 #define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
191 #define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
194 /*-----------------------------------------------------------------------
196 *----------------------------------------------------------------------*/
197 #define CFG_MBYTES_SDRAM (256) /* 256MB */
199 /*-----------------------------------------------------------------------
201 *----------------------------------------------------------------------*/
202 #define CONFIG_HARD_I2C 1 /* I2C with hardware support */
203 #undef CONFIG_SOFT_I2C /* I2C bit-banged */
204 #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
205 #define CFG_I2C_SLAVE 0x7F
207 #define CFG_I2C_MULTI_EEPROMS
208 #define CFG_I2C_EEPROM_ADDR (0xa8>>1)
209 #define CFG_I2C_EEPROM_ADDR_LEN 1
210 #define CFG_EEPROM_PAGE_WRITE_ENABLE
211 #define CFG_EEPROM_PAGE_WRITE_BITS 3
212 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
214 /* I2C SYSMON (LM75, AD7414 is almost compatible) */
215 #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
216 #define CONFIG_DTT_AD7414 1 /* use AD7414 */
217 #define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
218 #define CFG_DTT_MAX_TEMP 70
219 #define CFG_DTT_LOW_TEMP -30
220 #define CFG_DTT_HYSTERESIS 3
222 #define CONFIG_PREBOOT "echo;" \
223 "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
226 #undef CONFIG_BOOTARGS
228 #define CONFIG_EXTRA_ENV_SETTINGS \
230 "hostname=sequoia\0" \
231 "nfsargs=setenv bootargs root=/dev/nfs rw " \
232 "nfsroot=${serverip}:${rootpath}\0" \
233 "ramargs=setenv bootargs root=/dev/ram rw\0" \
234 "addip=setenv bootargs ${bootargs} " \
235 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
236 ":${hostname}:${netdev}:off panic=1\0" \
237 "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
238 "flash_nfs=run nfsargs addip addtty;" \
239 "bootm ${kernel_addr}\0" \
240 "flash_self=run ramargs addip addtty;" \
241 "bootm ${kernel_addr} ${ramdisk_addr}\0" \
242 "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
244 "rootpath=/opt/eldk/ppc_4xx\0" \
245 "bootfile=/tftpboot/sequoia/uImage\0" \
246 "kernel_addr=FE000000\0" \
247 "ramdisk_addr=FE180000\0" \
248 "load=tftp 100000 /tftpboot/sequoia/u-boot.bin\0" \
249 "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
250 "cp.b 100000 FFFA0000 60000\0" \
251 "upd=run load;run update\0" \
253 #define CONFIG_BOOTCOMMAND "run flash_self"
256 #define CONFIG_BOOTDELAY -1 /* autoboot disabled */
258 #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
261 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
262 #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
264 #define CONFIG_M88E1111_PHY 1
265 #define CONFIG_IBM_EMAC4_V4 1
266 #define CONFIG_MII 1 /* MII PHY management */
267 #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
269 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */
270 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
272 #define CONFIG_HAS_ETH0
273 #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
275 #define CONFIG_NET_MULTI 1
276 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
277 #define CONFIG_PHY1_ADDR 1
281 #define CONFIG_USB_OHCI
282 #define CONFIG_USB_STORAGE
284 /* Comment this out to enable USB 1.1 device */
285 #define USB_2_0_DEVICE
287 #define CMD_USB CFG_CMD_USB
289 #define CMD_USB 0 /* no USB on 440GRx */
290 #endif /* CONFIG_440EPX */
293 #define CONFIG_MAC_PARTITION
294 #define CONFIG_DOS_PARTITION
295 #define CONFIG_ISO_PARTITION
297 #define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
317 #define CONFIG_SUPPORT_VFAT
319 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
320 #include <cmd_confdefs.h>
322 /*-----------------------------------------------------------------------
323 * Miscellaneous configurable options
324 *----------------------------------------------------------------------*/
325 #define CFG_LONGHELP /* undef to save memory */
326 #define CFG_PROMPT "=> " /* Monitor Command Prompt */
327 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
328 #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
330 #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
332 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
333 #define CFG_MAXARGS 16 /* max number of command args */
334 #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
336 #define CFG_MEMTEST_START 0x0400000 /* memtest works on */
337 #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
339 #define CFG_LOAD_ADDR 0x100000 /* default load address */
340 #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
342 #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
344 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */
345 #define CONFIG_LOOPW 1 /* enable loopw command */
346 #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
347 #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
348 #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
350 /*-----------------------------------------------------------------------
352 *----------------------------------------------------------------------*/
354 #define CONFIG_PCI /* include pci support */
355 #define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
356 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
357 #define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
359 /* Board-specific PCI */
360 #define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
361 #define CFG_PCI_TARGET_INIT
362 #define CFG_PCI_MASTER_INIT
364 #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
365 #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
368 * For booting Linux, the board info and command line data
369 * have to be in the first 8 MB of memory, since this is
370 * the maximum mapped by the Linux kernel during initialization.
372 #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
374 /*-----------------------------------------------------------------------
375 * External Bus Controller (EBC) Setup
376 *----------------------------------------------------------------------*/
377 #define CFG_FLASH CFG_FLASH_BASE
378 #define CFG_NAND 0xD0000000
379 #define CFG_CPLD 0xC0000000
382 * On Sequoia CS0 and CS3 are switched when configuring for NAND booting
384 #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
385 #define CFG_NAND_CS 3 /* NAND chip connected to CSx */
386 /* Memory Bank 0 (NOR-FLASH) initialization */
387 #define CFG_EBC_PB0AP 0x03017300
388 #define CFG_EBC_PB0CR (CFG_FLASH | 0xba000)
390 /* Memory Bank 3 (NAND-FLASH) initialization */
391 #define CFG_EBC_PB3AP 0x018003c0
392 #define CFG_EBC_PB3CR (CFG_NAND | 0x1c000)
394 #define CFG_NAND_CS 0 /* NAND chip connected to CSx */
395 /* Memory Bank 3 (NOR-FLASH) initialization */
396 #define CFG_EBC_PB3AP 0x03017300
397 #define CFG_EBC_PB3CR (CFG_FLASH | 0xba000)
399 /* Memory Bank 0 (NAND-FLASH) initialization */
400 #define CFG_EBC_PB0AP 0x018003c0
401 #define CFG_EBC_PB0CR (CFG_NAND | 0x1c000)
404 /* Memory Bank 2 (CPLD) initialization */
405 #define CFG_EBC_PB2AP 0x24814580
406 #define CFG_EBC_PB2CR (CFG_CPLD | 0x38000)
408 /*-----------------------------------------------------------------------
409 * Cache Configuration
410 *----------------------------------------------------------------------*/
411 #define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
412 #define CFG_CACHELINE_SIZE 32 /* ... */
413 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
414 #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
418 * Internal Definitions
422 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
423 #define BOOTFLAG_WARM 0x02 /* Software reboot */
425 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
426 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
427 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
429 #endif /* __CONFIG_H */