git.sur5r.net Git - u-boot/blob - include/configs/tqma6.h

   1 /*
   2  * Copyright (C) 2013, 2014 Markus Niebel <Markus.Niebel@tq-group.com>
   3  *
   4  * Configuration settings for the TQ Systems TQMa6<Q,S> module.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 /* SPL */
  13 /* #if defined(CONFIG_SPL_BUILD) */
  14
  15 #define CONFIG_SPL_MMC_SUPPORT
  16 #define CONFIG_SPL_SPI_SUPPORT
  17 #define CONFIG_SPL_FAT_SUPPORT
  18 #define CONFIG_SPL_EXT_SUPPORT
  19
  20 /* common IMX6 SPL configuration */
  21 #include "imx6_spl.h"
  22
  23 /* #endif */
  24
  25 #include "mx6_common.h"
  26
  27 #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
  28 #define PHYS_SDRAM_SIZE                 (512u * SZ_1M)
  29 #elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
  30 #define PHYS_SDRAM_SIZE                 (1024u * SZ_1M)
  31 #endif
  32
  33 #define CONFIG_BOARD_EARLY_INIT_F
  34 #define CONFIG_BOARD_LATE_INIT
  35
  36 #define CONFIG_MXC_GPIO
  37 #define CONFIG_MXC_UART
  38
  39 /* SPI */
  40 #define CONFIG_CMD_SPI
  41 #define CONFIG_MXC_SPI
  42
  43 /* SPI Flash */
  44 #define CONFIG_SPI_FLASH
  45 #define CONFIG_SPI_FLASH_STMICRO
  46
  47 #define TQMA6_SPI_FLASH_SECTOR_SIZE     SZ_64K
  48
  49 #define CONFIG_CMD_SF
  50 #define CONFIG_SF_DEFAULT_BUS   0
  51 #define CONFIG_SF_DEFAULT_CS    0
  52 #define CONFIG_SF_DEFAULT_SPEED 50000000
  53 #define CONFIG_SF_DEFAULT_MODE  (SPI_MODE_0)
  54
  55 /* I2C Configs */
  56 #define CONFIG_CMD_I2C
  57 #define CONFIG_SYS_I2C
  58 #define CONFIG_SYS_I2C_MXC
  59 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  60 #define CONFIG_I2C_MULTI_BUS
  61 #define CONFIG_SYS_I2C_SPEED            100000
  62
  63 /* I2C SYSMON (LM75) */
  64 #define CONFIG_DTT_LM75
  65 #define CONFIG_DTT_MAX_TEMP             70
  66 #define CONFIG_DTT_MIN_TEMP             -30
  67 #define CONFIG_DTT_HYSTERESIS   3
  68 #define CONFIG_CMD_DTT
  69
  70 /* I2C EEPROM (M24C64) */
  71 #define CONFIG_SYS_I2C_EEPROM_ADDR                      0x50
  72 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN                  2
  73 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS           5 /* 32 Bytes */
  74 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS       20
  75 #define CONFIG_CMD_EEPROM
  76
  77 #define CONFIG_POWER
  78 #define CONFIG_POWER_I2C
  79 #define CONFIG_POWER_PFUZE100
  80 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  81 #define TQMA6_PFUZE100_I2C_BUS          2
  82
  83 /* MMC Configs */
  84 #define CONFIG_FSL_ESDHC
  85 #define CONFIG_FSL_USDHC
  86 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  87
  88 #define CONFIG_MMC
  89 #define CONFIG_CMD_MMC
  90 #define CONFIG_GENERIC_MMC
  91 #define CONFIG_BOUNCE_BUFFER
  92
  93 /* USB Configs */
  94 #define CONFIG_CMD_USB
  95 #define CONFIG_USB_EHCI
  96 #define CONFIG_USB_EHCI_MX6
  97 #define CONFIG_USB_STORAGE
  98 #define CONFIG_USB_HOST_ETHER
  99 #define CONFIG_USB_ETHER_SMSC95XX
 100 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
 101 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 102 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
 103
 104 /* Fuses */
 105 #define CONFIG_MXC_OCOTP
 106 #define CONFIG_CMD_FUSE
 107
 108 #define CONFIG_CMD_EXT2
 109 #define CONFIG_CMD_EXT4
 110 #define CONFIG_CMD_EXT4_WRITE
 111 #define CONFIG_CMD_FAT
 112 #define CONFIG_CMD_FS_GENERIC
 113 #define CONFIG_DOS_PARTITION
 114
 115 #define CONFIG_CMD_PING
 116 #define CONFIG_CMD_DHCP
 117 #define CONFIG_CMD_MII
 118 #define CONFIG_CMD_NET
 119
 120 #define CONFIG_FEC_MXC
 121 #define IMX_FEC_BASE                    ENET_BASE_ADDR
 122 #define CONFIG_PHYLIB
 123 #define CONFIG_MII
 124
 125 #define CONFIG_ARP_TIMEOUT              200UL
 126 /* Network config - Allow larger/faster download for TFTP/NFS */
 127 #define CONFIG_IP_DEFRAG
 128 #define CONFIG_TFTP_BLOCKSIZE   4096
 129 #define CONFIG_NFS_READ_SIZE    4096
 130
 131 /* allow to overwrite serial and ethaddr */
 132 #define CONFIG_ENV_OVERWRITE
 133 #define CONFIG_CONS_INDEX               1
 134 #define CONFIG_BAUDRATE                 115200
 135
 136 /* Command definition */
 137 #define CONFIG_CMD_BMODE
 138 #define CONFIG_CMD_BOOTZ
 139 #define CONFIG_CMD_ITEST
 140 #define CONFIG_CMD_SETEXPR
 141
 142 #define CONFIG_BOOTDELAY                3
 143
 144 #define CONFIG_LOADADDR                 0x12000000
 145
 146 /* place code in last 4 MiB of RAM */
 147 #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
 148 #define CONFIG_SYS_TEXT_BASE            0x2fc00000
 149 #elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
 150 #define CONFIG_SYS_TEXT_BASE            0x4fc00000
 151 #endif
 152
 153 #define CONFIG_ENV_SIZE                 (SZ_8K)
 154 /* Size of malloc() pool */
 155 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 2 * SZ_1M)
 156
 157 #if defined(CONFIG_TQMA6X_MMC_BOOT)
 158
 159 #define CONFIG_ENV_IS_IN_MMC
 160 #define TQMA6_UBOOT_OFFSET              SZ_1K
 161 #define TQMA6_UBOOT_SECTOR_START        0x2
 162 #define TQMA6_UBOOT_SECTOR_COUNT        0x7fe
 163
 164 #define CONFIG_ENV_OFFSET               SZ_1M
 165 #define CONFIG_SYS_MMC_ENV_DEV          0
 166
 167 #define TQMA6_FDT_OFFSET                (2 * SZ_1M)
 168 #define TQMA6_FDT_SECTOR_START          0x1000
 169 #define TQMA6_FDT_SECTOR_COUNT          0x800
 170
 171 #define TQMA6_KERNEL_SECTOR_START       0x2000
 172 #define TQMA6_KERNEL_SECTOR_COUNT       0x2000
 173
 174 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 175         "uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0"                \
 176         "uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"                 \
 177         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 178         "fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                     \
 179         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 180         "kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"               \
 181         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0"                       \
 182         "loadimage=mmc dev ${mmcdev}; "                                        \
 183                 "mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0"       \
 184         "loadfdt=mmc dev ${mmcdev}; "                                          \
 185                 "mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0"             \
 186         "update_uboot=if tftp ${uboot}; then "                                 \
 187                 "if itest ${filesize} > 0; then "                              \
 188                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 189                         "setexpr blkc ${filesize} / 0x200; "                   \
 190                         "setexpr blkc ${blkc} + 1; "                           \
 191                         "if itest ${blkc} <= ${uboot_size}; then "             \
 192                                 "mmc write ${loadaddr} ${uboot_start} "        \
 193                                         "${blkc}; "                            \
 194                         "fi; "                                                 \
 195                 "fi; fi; "                                                     \
 196                 "setenv filesize; setenv blkc \0"                              \
 197         "update_kernel=run kernel_name; "                                      \
 198                 "if tftp ${kernel}; then "                                     \
 199                         "if itest ${filesize} > 0; then "                      \
 200                                 "mmc dev ${mmcdev}; mmc rescan; "              \
 201                                 "setexpr blkc ${filesize} / 0x200; "           \
 202                                 "setexpr blkc ${blkc} + 1; "                   \
 203                                 "if itest ${blkc} <= ${kernel_size}; then "    \
 204                                         "mmc write ${loadaddr} "               \
 205                                                 "${kernel_start} ${blkc}; "    \
 206                                 "fi; "                                         \
 207                         "fi; "                                                 \
 208                 "fi; "                                                         \
 209                 "setenv filesize; setenv blkc \0"                              \
 210         "update_fdt=if tftp ${fdt_file}; then "                                \
 211                 "if itest ${filesize} > 0; then "                              \
 212                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 213                         "setexpr blkc ${filesize} / 0x200; "                   \
 214                         "setexpr blkc ${blkc} + 1; "                           \
 215                         "if itest ${blkc} <= ${fdt_size}; then "               \
 216                                 "mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
 217                         "fi; "                                                 \
 218                 "fi; fi; "                                                     \
 219                 "setenv filesize; setenv blkc \0"                              \
 220
 221 #define CONFIG_BOOTCOMMAND \
 222         "run mmcboot; run netboot; run panicboot"
 223
 224 #elif defined(CONFIG_TQMA6X_SPI_BOOT)
 225
 226 #define TQMA6_UBOOT_OFFSET              0x400
 227 #define TQMA6_UBOOT_SECTOR_START        0x0
 228 /* max u-boot size: 512k */
 229 #define TQMA6_UBOOT_SECTOR_SIZE         TQMA6_SPI_FLASH_SECTOR_SIZE
 230 #define TQMA6_UBOOT_SECTOR_COUNT        0x8
 231 #define TQMA6_UBOOT_SIZE                (TQMA6_UBOOT_SECTOR_SIZE * \
 232                                          TQMA6_UBOOT_SECTOR_COUNT)
 233
 234 #define CONFIG_ENV_IS_IN_SPI_FLASH
 235 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 236 #define CONFIG_ENV_OFFSET               (TQMA6_UBOOT_SIZE)
 237 #define CONFIG_ENV_SECT_SIZE            TQMA6_SPI_FLASH_SECTOR_SIZE
 238 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + \
 239                                          CONFIG_ENV_SECT_SIZE)
 240
 241 #define CONFIG_ENV_SPI_BUS              (CONFIG_SF_DEFAULT_BUS)
 242 #define CONFIG_ENV_SPI_CS               (CONFIG_SF_DEFAULT_CS)
 243 #define CONFIG_ENV_SPI_MAX_HZ           (CONFIG_SF_DEFAULT_SPEED)
 244 #define CONFIG_ENV_SPI_MODE             (CONFIG_SF_DEFAULT_MODE)
 245
 246 #define TQMA6_FDT_OFFSET                (CONFIG_ENV_OFFSET_REDUND + \
 247                                          CONFIG_ENV_SECT_SIZE)
 248 #define TQMA6_FDT_SECT_SIZE             (TQMA6_SPI_FLASH_SECTOR_SIZE)
 249
 250 #define TQMA6_FDT_SECTOR_START          0x0a /* 8 Sector u-boot, 2 Sector env */
 251 #define TQMA6_FDT_SECTOR_COUNT          0x01
 252
 253 #define TQMA6_KERNEL_SECTOR_START       0x10
 254 #define TQMA6_KERNEL_SECTOR_COUNT       0x60
 255
 256 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 257         "mmcblkdev=0\0"                                                        \
 258         "uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0"                     \
 259         "uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"              \
 260         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 261         "fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                  \
 262         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 263         "kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"            \
 264         "update_uboot=if tftp ${uboot}; then "                                 \
 265                 "if itest ${filesize} > 0; then "                              \
 266                         "setexpr blkc ${filesize} + "                          \
 267                                 __stringify(TQMA6_UBOOT_OFFSET) "; "           \
 268                         "setexpr size ${uboot_sectors} * "                     \
 269                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 270                         "if itest ${blkc} <= ${size}; then "                   \
 271                                 "sf probe; "                                   \
 272                                 "sf erase 0 ${size}; "                         \
 273                                 "sf write ${loadaddr} ${uboot_offset} "        \
 274                                         "${filesize}; "                        \
 275                         "fi; "                                                 \
 276                 "fi; fi; "                                                     \
 277                 "setenv filesize 0; setenv blkc; setenv size \0"               \
 278         "update_kernel=run kernel_name; if tftp ${kernel}; then "              \
 279                 "if itest ${filesize} > 0; then "                              \
 280                         "setexpr size ${kernel_sectors} * "                    \
 281                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 282                         "setexpr offset ${kernel_start} * "                    \
 283                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 284                         "if itest ${filesize} <= ${size}; then "               \
 285                                 "sf probe; "                                   \
 286                                 "sf erase ${offset} ${size}; "                 \
 287                                 "sf write ${loadaddr} ${offset} "              \
 288                                         "${filesize}; "                        \
 289                         "fi; "                                                 \
 290                 "fi; fi; "                                                     \
 291                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 292         "update_fdt=if tftp ${fdt_file}; then "                                \
 293                 "if itest ${filesize} > 0; then "                              \
 294                         "setexpr size ${fdt_sectors} * "                       \
 295                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 296                         "setexpr offset ${fdt_start} * "                       \
 297                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 298                         "if itest ${filesize} <= ${size}; then "               \
 299                                 "sf probe; "                                   \
 300                                 "sf erase ${offset} ${size}; "                 \
 301                                 "sf write ${loadaddr} ${offset} "              \
 302                                         "${filesize}; "                        \
 303                         "fi; "                                                 \
 304                 "fi; fi; "                                                     \
 305                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 306         "loadimage=sf probe; "                                                 \
 307                 "setexpr size ${kernel_sectors} * "                            \
 308                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 309                 "setexpr offset ${kernel_start} * "                            \
 310                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 311                 "sf read ${loadaddr} ${offset} ${size}; "                      \
 312                 "setenv size ; setenv offset\0"                                \
 313         "loadfdt=sf probe; "                                                   \
 314                 "setexpr size ${fdt_sectors} * "                               \
 315                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 316                 "setexpr offset ${fdt_start} * "                               \
 317                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 318                 "sf read ${${fdt_addr}} ${offset} ${size}; "                   \
 319                 "setenv size ; setenv offset\0"                                \
 320
 321
 322 #define CONFIG_BOOTCOMMAND                                                     \
 323         "sf probe; run mmcboot; run netboot; run panicboot"                    \
 324
 325 #else
 326
 327 #error "need to define boot source"
 328
 329 #endif
 330
 331 /* 128 MiB offset as in ARM related docu for linux suggested */
 332 #define TQMA6_FDT_ADDRESS               0x18000000
 333
 334 #define CONFIG_EXTRA_ENV_SETTINGS                                              \
 335         "board=tqma6\0"                                                        \
 336         "uimage=uImage\0"                                                      \
 337         "zimage=zImage\0"                                                      \
 338         "boot_type=bootz\0"                                                    \
 339         "kernel_name=if test \"${boot_type}\" != bootz; then "                 \
 340                 "setenv kernel ${uimage}; "                                    \
 341                 "else setenv kernel ${zimage}; fi\0"                           \
 342         "uboot=u-boot.imx\0"                                                   \
 343         "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0"                               \
 344         "fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0"                          \
 345         "console=" CONFIG_CONSOLE_DEV "\0"                                     \
 346         "fdt_high=0xffffffff\0"                                                \
 347         "initrd_high=0xffffffff\0"                                             \
 348         "addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0"  \
 349         "addfb=setenv bootargs ${bootargs} "                                   \
 350                 "imx-fbdev.legacyfb_depth=32 consoleblank=0\0"                 \
 351         "mmcpart=2\0"                                                          \
 352         "mmcblkdev=0\0"                                                        \
 353         "mmcargs=run addmmc addtty addfb\0"                                    \
 354         "addmmc=setenv bootargs ${bootargs} "                                  \
 355                 "root=/dev/mmcblk${mmcblkdev}p${mmcpart} rw rootwait\0"        \
 356         "mmcboot=echo Booting from mmc ...; "                                  \
 357                 "setenv bootargs; "                                            \
 358                 "run mmcargs; "                                                \
 359                 "run loadimage; "                                              \
 360                 "if run loadfdt; then "                                        \
 361                         "echo boot device tree kernel ...; "                   \
 362                         "${boot_type} ${loadaddr} - ${fdt_addr}; "             \
 363                 "else "                                                        \
 364                         "${boot_type}; "                                       \
 365                 "fi;\0"                                                        \
 366                 "setenv bootargs \0"                                           \
 367         "netdev=eth0\0"                                                        \
 368         "rootpath=/srv/nfs/tqma6\0"                                            \
 369         "ipmode=static\0"                                                      \
 370         "netargs=run addnfs addip addtty addfb\0"                              \
 371         "addnfs=setenv bootargs ${bootargs} "                                  \
 372                 "root=/dev/nfs rw "                                            \
 373                 "nfsroot=${serverip}:${rootpath},v3,tcp;\0"                    \
 374         "addip_static=setenv bootargs ${bootargs} "                            \
 375                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:"            \
 376                 "${hostname}:${netdev}:off\0"                                  \
 377         "addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0"                  \
 378         "addip=if test \"${ipmode}\" != static; then "                         \
 379                 "run addip_dynamic; else run addip_static; fi\0"               \
 380         "set_getcmd=if test \"${ipmode}\" != static; then "                    \
 381                 "setenv getcmd dhcp; setenv autoload yes; "                    \
 382                 "else setenv getcmd tftp; setenv autoload no; fi\0"            \
 383         "netboot=echo Booting from net ...; "                                  \
 384                 "run kernel_name; "                                            \
 385                 "run set_getcmd; "                                             \
 386                 "setenv bootargs; "                                            \
 387                 "run netargs; "                                                \
 388                 "if ${getcmd} ${kernel}; then "                                \
 389                         "if ${getcmd} ${fdt_addr} ${fdt_file}; then "          \
 390                                 "${boot_type} ${loadaddr} - ${fdt_addr}; "     \
 391                         "fi; "                                                 \
 392                 "fi; "                                                         \
 393                 "echo ... failed\0"                                            \
 394         "panicboot=echo No boot device !!! reset\0"                            \
 395         TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                      \
 396
 397 /* Miscellaneous configurable options */
 398 #define CONFIG_SYS_LONGHELP
 399 #define CONFIG_SYS_HUSH_PARSER
 400 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 401
 402 #define CONFIG_AUTO_COMPLETE
 403 #define CONFIG_SYS_CBSIZE               512
 404
 405 /* Print Buffer Size */
 406 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 407                                          sizeof(CONFIG_SYS_PROMPT) + 16)
 408 #define CONFIG_SYS_MAXARGS              16
 409 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 410
 411 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 412
 413 #define CONFIG_CMDLINE_EDITING
 414 #define CONFIG_STACKSIZE                (128u * SZ_1K)
 415
 416 /* Physical Memory Map */
 417 #define CONFIG_NR_DRAM_BANKS            1
 418 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 419
 420 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 421 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 422 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 423
 424 #define CONFIG_SYS_INIT_SP_OFFSET \
 425         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 426 #define CONFIG_SYS_INIT_SP_ADDR \
 427         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 428
 429 #define CONFIG_OF_LIBFDT
 430 #define CONFIG_OF_BOARD_SETUP
 431 #define CONFIG_FIT
 432 #define CONFIG_FIT_VERBOSE
 433
 434 #ifndef CONFIG_SYS_DCACHE_OFF
 435 #define CONFIG_CMD_CACHE
 436 #endif
 437
 438 /*
 439  * All the defines above are for the TQMa6 SoM
 440  *
 441  * Now include the baseboard specific configuration
 442  */
 443 #ifdef CONFIG_MBA6
 444 #include "tqma6_mba6.h"
 445 #else
 446 #error "No baseboard for the TQMa6 defined!"
 447 #endif
 448
 449 /* Support at least the sensor on TQMa6 SOM */
 450 #if !defined(CONFIG_DTT_SENSORS)
 451 #define CONFIG_DTT_SENSORS              { 0 }
 452 #endif
 453
 454 #endif /* __CONFIG_H */