git.sur5r.net Git - u-boot/blob - include/configs/wireless_space.h

   1 /*
   2  * Copyright (C) 2011 Albert ARIBAUD <albert.u.boot@aribaud.net>
   3  *
   4  * Based on the netspace_v2 code which is
   5  * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef _CONFIG_WIRELESS_SPACE_H
  11 #define _CONFIG_WIRELESS_SPACE_H
  12
  13 /*
  14  * Machine number definition
  15  */
  16 #define MACH_TYPE_WIRELESS_SPACE        2500 /* is missing in mach-types.h */
  17 #define CONFIG_MACH_TYPE                MACH_TYPE_WIRELESS_SPACE
  18 #define CONFIG_IDENT_STRING             " Wireless Space"
  19
  20 /*
  21  * High Level Configuration Options (easy to change)
  22  */
  23 #define CONFIG_FEROCEON_88FR131         /* CPU Core subversion */
  24 /* SoC name */
  25 #define CONFIG_KW88F6281
  26 #define CONFIG_SKIP_LOWLEVEL_INIT       /* disable board lowlevel_init */
  27
  28 /*
  29  * Commands configuration
  30  */
  31 #define CONFIG_SYS_NO_FLASH             /* no NOR or SPI flash */
  32 #define CONFIG_CMD_ENV
  33 #define CONFIG_CMD_DHCP
  34 #define CONFIG_CMD_PING
  35 #define CONFIG_CMD_NAND
  36 #define CONFIG_CMD_I2C
  37 #define CONFIG_CMD_IDE
  38 #define CONFIG_CMD_USB
  39
  40 /*
  41  * Core clock definition
  42  */
  43 #define CONFIG_SYS_TCLK                 166000000 /* 166MHz */
  44
  45 /*
  46  * SDRAM configuration
  47  */
  48 #define CONFIG_NR_DRAM_BANKS            1
  49
  50 /*
  51  * Different SDRAM configuration and size for some of the boards derived
  52  * from the Network Space v2
  53  */
  54
  55 /*
  56  * mv-common.h should be defined after CMD configs since it used them
  57  * to enable certain macros
  58  */
  59 #include "mv-common.h"
  60
  61 /* Remove or override few declarations from mv-common.h */
  62 #undef CONFIG_RBTREE
  63 #undef CONFIG_SYS_IDE_MAXBUS
  64 #undef CONFIG_SYS_IDE_MAXDEVICE
  65 #define CONFIG_SYS_IDE_MAXBUS           1
  66 #define CONFIG_SYS_IDE_MAXDEVICE        1
  67
  68 /*
  69  * Ethernet Driver configuration
  70  */
  71 #ifdef CONFIG_CMD_NET
  72 #define CONFIG_MISC_INIT_R /* misc_init_r() initializes MAC address */
  73 #define CONFIG_MVGBE_PORTS      {1, 0}  /* enable only egiga0... */
  74 #define PORT_SERIAL_CONTROL_VALUE 0x00A4260E /* ... tied to the switch... */
  75 #define CONFIG_PHY_BASE_ADR 0xa         /* ... through a 'fake' PHY */
  76 #define CONFIG_MII
  77 #undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  78 #define CONFIG_NETCONSOLE
  79 #define CONFIG_MV88E61XX_SWITCH
  80 #define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
  81 #define CONFIG_MV88E61XX_CMD
  82 #define CONFIG_CMD_TFTPPUT
  83 #endif /* CONFIG_CMD_NET */
  84
  85 /*
  86  * SATA Driver configuration
  87  */
  88 #ifdef CONFIG_MVSATA_IDE
  89 #define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
  90 #endif /* CONFIG_MVSATA_IDE */
  91
  92 /*
  93  * Enable GPI0 support
  94  */
  95 #define CONFIG_KIRKWOOD_GPIO
  96
  97 /*
  98  * Enable I2C support
  99  */
 100 #ifdef CONFIG_CMD_I2C
 101 /* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
 102 #define CONFIG_CMD_EEPROM
 103 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
 104 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       4 /* 16-byte page size */
 105 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1 /* 8-bit device address */
 106 #endif /* CONFIG_CMD_I2C */
 107
 108 /*
 109  * Partition support
 110  */
 111 #define CONFIG_DOS_PARTITION
 112 #define CONFIG_EFI_PARTITION
 113
 114 /*
 115  * File systems support
 116  */
 117 #define CONFIG_CMD_EXT2
 118 #define CONFIG_CMD_FAT
 119
 120 /*
 121  * Use the HUSH parser
 122  */
 123 #define CONFIG_SYS_HUSH_PARSER
 124
 125 /*
 126  * Console configuration
 127  */
 128 #define CONFIG_CONSOLE_MUX
 129 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 130
 131 /*
 132  * Enable device tree support
 133  */
 134 #define CONFIG_OF_LIBFDT
 135
 136 /*
 137  * Environment variables configurations
 138  */
 139
 140 #define CONFIG_ENV_IS_IN_NAND
 141 #define CONFIG_ENV_SECT_SIZE            0x20000 /* 128KB */
 142 #define CONFIG_ENV_SIZE                 0x20000 /* 128KB */
 143 #define CONFIG_ENV_OFFSET               0x80000 /* env starts here */
 144
 145 /*
 146  * Board-specific command to make using buttons etc easier
 147  */
 148
 149 #define CONFIG_WIRELESS_SPACE_CMD
 150
 151 /*
 152  * Default environment variables
 153  */
 154 #define CONFIG_PREBOOT
 155
 156 #define CONFIG_BOOTARGS "console=ttyS0,115200"
 157
 158 #define CONFIG_BOOTCOMMAND                                      \
 159         "if run usbload || run diskload; then bootm; fi"
 160
 161 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 162         "stdin=serial\0"                                        \
 163         "stdout=serial\0"                                       \
 164         "stderr=serial\0"                                       \
 165         "bootfile=uImage\0"                                     \
 166         "loadaddr=0x800000\0"                                   \
 167         "autoload=no\0"                                         \
 168         "netconsole="                                           \
 169                 "set stdin $stdin,nc; "                         \
 170                 "set stdout $stdout,nc; "                       \
 171                 "set stderr $stderr,nc;\0"                      \
 172         "diskload=ide reset && "                                \
 173                 "ext2load ide 0:1 $loadaddr /boot/$bootfile\0"  \
 174         "usbload=usb start && "                                 \
 175                 "fatload usb 0:1 $loadaddr /boot/$bootfile\0"   \
 176         "preboot="                                              \
 177                 "dhcp && run netconsole\0"
 178
 179 #endif /* _CONFIG_WIRELESS_SPACE_H */