git.sur5r.net Git - u-boot/blob - include/configs/xpedite537x.h

   1 /*
   2  * Copyright 2008 Extreme Engineering Solutions, Inc.
   3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * xpedite537x board configuration file
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  */
  17 #define CONFIG_BOOKE            1       /* BOOKE */
  18 #define CONFIG_E500             1       /* BOOKE e500 family */
  19 #define CONFIG_MPC8572          1
  20 #define CONFIG_XPEDITE5370      1
  21 #define CONFIG_SYS_BOARD_NAME   "XPedite5370"
  22 #define CONFIG_SYS_FORM_3U_VPX  1
  23 #define CONFIG_BOARD_EARLY_INIT_R       /* Call board_pre_init */
  24 #define CONFIG_SYS_GENERIC_BOARD
  25 #define CONFIG_DISPLAY_BOARDINFO
  26
  27 #ifndef CONFIG_SYS_TEXT_BASE
  28 #define CONFIG_SYS_TEXT_BASE    0xfff80000
  29 #endif
  30
  31 #define CONFIG_PCI              1       /* Enable PCI/PCIE */
  32 #define CONFIG_PCI_PNP          1       /* do pci plug-and-play */
  33 #define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup */
  34 #define CONFIG_PCIE1            1       /* PCIE controler 1 */
  35 #define CONFIG_PCIE2            1       /* PCIE controler 2 */
  36 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  37 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  38 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  39 #define CONFIG_FSL_PCIE_RESET   1       /* need PCIe reset errata */
  40 #define CONFIG_FSL_LAW          1       /* Use common FSL init code */
  41 #define CONFIG_FSL_ELBC         1
  42
  43 /*
  44  * Multicore config
  45  */
  46 #define CONFIG_MP
  47 #define CONFIG_BPTR_VIRT_ADDR   0xee000000      /* virt boot page address */
  48 #define CONFIG_MPC8xxx_DISABLE_BPTR             /* Don't leave BPTR enabled */
  49
  50 /*
  51  * DDR config
  52  */
  53 #define CONFIG_SYS_FSL_DDR2
  54 #undef CONFIG_FSL_DDR_INTERACTIVE
  55 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
  56 #define CONFIG_DDR_SPD
  57 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  58 #define SPD_EEPROM_ADDRESS1             0x54    /* Both channels use the */
  59 #define SPD_EEPROM_ADDRESS2             0x54    /* same SPD data         */
  60 #define SPD_EEPROM_OFFSET               0x200   /* OFFSET of SPD in EEPROM */
  61 #define CONFIG_NUM_DDR_CONTROLLERS      2
  62 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  63 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  64 #define CONFIG_DDR_ECC
  65 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  66 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000 /* DDR is system memory*/
  67 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  68 #define CONFIG_VERY_BIG_RAM
  69
  70 #ifndef __ASSEMBLY__
  71 extern unsigned long get_board_sys_clk(unsigned long dummy);
  72 extern unsigned long get_board_ddr_clk(unsigned long dummy);
  73 #endif
  74
  75 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0) /* sysclk for MPC85xx */
  76 #define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk(0) /* ddrclk for MPC85xx */
  77
  78 /*
  79  * These can be toggled for performance analysis, otherwise use default.
  80  */
  81 #define CONFIG_L2_CACHE                 /* toggle L2 cache */
  82 #define CONFIG_BTB                      /* toggle branch predition */
  83 #define CONFIG_ENABLE_36BIT_PHYS        1
  84
  85 #define CONFIG_SYS_CCSRBAR              0xef000000
  86 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  87
  88 /*
  89  * Diagnostics
  90  */
  91 #define CONFIG_SYS_ALT_MEMTEST
  92 #define CONFIG_SYS_MEMTEST_START        0x10000000
  93 #define CONFIG_SYS_MEMTEST_END          0x20000000
  94 #define CONFIG_POST                     (CONFIG_SYS_POST_MEMORY | \
  95                                          CONFIG_SYS_POST_I2C)
  96 #define I2C_ADDR_LIST                   {CONFIG_SYS_I2C_DS1621_ADDR,    \
  97                                          CONFIG_SYS_I2C_DS4510_ADDR,    \
  98                                          CONFIG_SYS_I2C_EEPROM_ADDR,    \
  99                                          CONFIG_SYS_I2C_LM90_ADDR,      \
 100                                          CONFIG_SYS_I2C_PCA953X_ADDR0,  \
 101                                          CONFIG_SYS_I2C_PCA953X_ADDR1,  \
 102                                          CONFIG_SYS_I2C_PCA953X_ADDR2,  \
 103                                          CONFIG_SYS_I2C_PCA953X_ADDR3,  \
 104                                          CONFIG_SYS_I2C_PEX8518_ADDR,   \
 105                                          CONFIG_SYS_I2C_RTC_ADDR}
 106 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */
 107 #define I2C_ADDR_IGNORE_LIST            {0x50}
 108
 109 /*
 110  * Memory map
 111  * 0x0000_0000  0x7fff_ffff     DDR                     2G Cacheable
 112  * 0x8000_0000  0xbfff_ffff     PCIe1 Mem               1G non-cacheable
 113  * 0xc000_0000  0xcfff_ffff     PCIe2 Mem               256M non-cacheable
 114  * 0xe000_0000  0xe7ff_ffff     SRAM/SSRAM/L1 Cache     128M non-cacheable
 115  * 0xe800_0000  0xe87f_ffff     PCIe1 IO                8M non-cacheable
 116  * 0xe880_0000  0xe8ff_ffff     PCIe2 IO                8M non-cacheable
 117  * 0xee00_0000  0xee00_ffff     Boot page translation   4K non-cacheable
 118  * 0xef00_0000  0xef0f_ffff     CCSR/IMMR               1M non-cacheable
 119  * 0xef80_0000  0xef8f_ffff     NAND Flash              1M non-cacheable
 120  * 0xf000_0000  0xf7ff_ffff     NOR Flash 2             128M non-cacheable
 121  * 0xf800_0000  0xffff_ffff     NOR Flash 1             128M non-cacheable
 122  */
 123
 124 #define CONFIG_SYS_LBC_LCRR     (LCRR_CLKDIV_8 | LCRR_EADC_3)
 125
 126 /*
 127  * NAND flash configuration
 128  */
 129 #define CONFIG_SYS_NAND_BASE            0xef800000
 130 #define CONFIG_SYS_NAND_BASE2           0xef840000 /* Unused at this time */
 131 #define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE, \
 132                                          CONFIG_SYS_NAND_BASE2}
 133 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 134 #define CONFIG_NAND_FSL_ELBC
 135
 136 /*
 137  * NOR flash configuration
 138  */
 139 #define CONFIG_SYS_FLASH_BASE           0xf8000000
 140 #define CONFIG_SYS_FLASH_BASE2          0xf0000000
 141 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 142 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
 143 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 144 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Flash Erase Timeout (ms) */
 145 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Flash Write Timeout (ms) */
 146 #define CONFIG_FLASH_CFI_DRIVER
 147 #define CONFIG_SYS_FLASH_CFI
 148 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 149 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST       { {0xfff40000, 0xc0000}, \
 150                                                   {0xf7f40000, 0xc0000} }
 151 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 152
 153 /*
 154  * Chip select configuration
 155  */
 156 /* NOR Flash 0 on CS0 */
 157 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE  | \
 158                                  BR_PS_16               | \
 159                                  BR_V)
 160 #define CONFIG_SYS_OR0_PRELIM   (OR_AM_128MB            | \
 161                                  OR_GPCM_CSNT           | \
 162                                  OR_GPCM_XACS           | \
 163                                  OR_GPCM_ACS_DIV2       | \
 164                                  OR_GPCM_SCY_8          | \
 165                                  OR_GPCM_TRLX           | \
 166                                  OR_GPCM_EHTR           | \
 167                                  OR_GPCM_EAD)
 168
 169 /* NOR Flash 1 on CS1 */
 170 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FLASH_BASE2 | \
 171                                  BR_PS_16               | \
 172                                  BR_V)
 173 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 174
 175 /* NAND flash on CS2 */
 176 #define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_NAND_BASE   | \
 177                                  (2<<BR_DECC_SHIFT)     | \
 178                                  BR_PS_8                | \
 179                                  BR_MS_FCM              | \
 180                                  BR_V)
 181
 182 /* NAND flash on CS2 */
 183 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_256KB    | \
 184                                  OR_FCM_PGS     | \
 185                                  OR_FCM_CSCT    | \
 186                                  OR_FCM_CST     | \
 187                                  OR_FCM_CHT     | \
 188                                  OR_FCM_SCY_1   | \
 189                                  OR_FCM_TRLX    | \
 190                                  OR_FCM_EHTR)
 191
 192 /* NAND flash on CS3 */
 193 #define CONFIG_SYS_BR3_PRELIM   (CONFIG_SYS_NAND_BASE2  | \
 194                                  (2<<BR_DECC_SHIFT)     | \
 195                                  BR_PS_8                | \
 196                                  BR_MS_FCM              | \
 197                                  BR_V)
 198 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 199
 200 /*
 201  * Use L1 as initial stack
 202  */
 203 #define CONFIG_SYS_INIT_RAM_LOCK        1
 204 #define CONFIG_SYS_INIT_RAM_ADDR        0xe0000000
 205 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 206
 207 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 208 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 209
 210 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
 211 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc */
 212
 213 /*
 214  * Serial Port
 215  */
 216 #define CONFIG_CONS_INDEX               1
 217 #define CONFIG_SYS_NS16550
 218 #define CONFIG_SYS_NS16550_SERIAL
 219 #define CONFIG_SYS_NS16550_REG_SIZE     1
 220 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 221 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 222 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 223 #define CONFIG_SYS_BAUDRATE_TABLE       \
 224         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 225 #define CONFIG_BAUDRATE                 115200
 226 #define CONFIG_LOADS_ECHO               1       /* echo on for serial download */
 227 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 228
 229 /*
 230  * Use the HUSH parser
 231  */
 232 #define CONFIG_SYS_HUSH_PARSER
 233
 234 /*
 235  * Pass open firmware flat tree
 236  */
 237 #define CONFIG_OF_LIBFDT                1
 238 #define CONFIG_OF_BOARD_SETUP           1
 239 #define CONFIG_OF_STDOUT_VIA_ALIAS      1
 240
 241 /*
 242  * I2C
 243  */
 244 #define CONFIG_SYS_I2C
 245 #define CONFIG_SYS_I2C_FSL
 246 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 247 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 248 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 249 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 250 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 251 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 252 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 253
 254 /* PEX8518 slave I2C interface */
 255 #define CONFIG_SYS_I2C_PEX8518_ADDR     0x70
 256
 257 /* I2C DS1631 temperature sensor */
 258 #define CONFIG_SYS_I2C_DS1621_ADDR      0x48
 259 #define CONFIG_DTT_DS1621
 260 #define CONFIG_DTT_SENSORS              { 0 }
 261 #define CONFIG_SYS_I2C_LM90_ADDR        0x4c
 262
 263 /* I2C EEPROM - AT24C128B */
 264 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x54
 265 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 266 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
 267 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
 268
 269 /* I2C RTC */
 270 #define CONFIG_RTC_M41T11               1
 271 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 272 #define CONFIG_SYS_M41T11_BASE_YEAR     2000
 273
 274 /* GPIO/EEPROM/SRAM */
 275 #define CONFIG_DS4510
 276 #define CONFIG_SYS_I2C_DS4510_ADDR      0x51
 277
 278 /* GPIO */
 279 #define CONFIG_PCA953X
 280 #define CONFIG_SYS_I2C_PCA953X_ADDR0    0x18
 281 #define CONFIG_SYS_I2C_PCA953X_ADDR1    0x1c
 282 #define CONFIG_SYS_I2C_PCA953X_ADDR2    0x1e
 283 #define CONFIG_SYS_I2C_PCA953X_ADDR3    0x1f
 284 #define CONFIG_SYS_I2C_PCA953X_ADDR     CONFIG_SYS_I2C_PCA953X_ADDR0
 285
 286 /*
 287  * PU = pulled high, PD = pulled low
 288  * I = input, O = output, IO = input/output
 289  */
 290 /* PCA9557 @ 0x18*/
 291 #define CONFIG_SYS_PCA953X_C0_SER0_EN           0x01 /* PU; UART0 enable (1: enabled) */
 292 #define CONFIG_SYS_PCA953X_C0_SER0_MODE         0x02 /* PU; UART0 serial mode select */
 293 #define CONFIG_SYS_PCA953X_C0_SER1_EN           0x04 /* PU; UART1 enable (1: enabled) */
 294 #define CONFIG_SYS_PCA953X_C0_SER1_MODE         0x08 /* PU; UART1 serial mode select */
 295 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS     0x10 /* PU; Boot flash CS select */
 296 #define CONFIG_SYS_PCA953X_NVM_WP               0x20 /* PU; Set to 0 to enable NVM writing */
 297 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2        0x40 /* VID2 of ISL6262 */
 298 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3        0x80 /* VID3 of ISL6262 */
 299
 300 /* PCA9557 @ 0x1c*/
 301 #define CONFIG_SYS_PCA953X_XMC0_ROOT0           0x01 /* PU; Low if XMC is RC */
 302 #define CONFIG_SYS_PCA953X_XMC0_MVMR0           0x02 /* XMC EEPROM write protect */
 303 #define CONFIG_SYS_PCA953X_XMC0_WAKE            0x04 /* PU; XMC wake */
 304 #define CONFIG_SYS_PCA953X_XMC0_BIST            0x08 /* PU; XMC built in self test */
 305 #define CONFIG_SYS_PCA953X_XMC_PRESENT          0x10 /* PU; Low if XMC module installed */
 306 #define CONFIG_SYS_PCA953X_PMC_PRESENT          0x20 /* PU; Low if PMC module installed */
 307 #define CONFIG_SYS_PCA953X_PMC0_MONARCH         0x40 /* PMC monarch mode enable */
 308 #define CONFIG_SYS_PCA953X_PMC0_EREADY          0x80 /* PU; PMC PCI eready */
 309
 310 /* PCA9557 @ 0x1e*/
 311 #define CONFIG_SYS_PCA953X_P0_GA0               0x01 /* PU; VPX Geographical address */
 312 #define CONFIG_SYS_PCA953X_P0_GA1               0x02 /* PU; VPX Geographical address */
 313 #define CONFIG_SYS_PCA953X_P0_GA2               0x04 /* PU; VPX Geographical address */
 314 #define CONFIG_SYS_PCA953X_P0_GA3               0x08 /* PU; VPX Geographical address */
 315 #define CONFIG_SYS_PCA953X_P0_GA4               0x10 /* PU; VPX Geographical address */
 316 #define CONFIG_SYS_PCA953X_P0_GAP               0x20 /* PU; tied to VPX P0.GAP */
 317 #define CONFIG_SYS_PCA953X_P1_SYSEN             0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */
 318
 319 /* PCA9557 @ 0x1f */
 320 #define CONFIG_SYS_PCA953X_GPIO_VPX0            0x01 /* PU */
 321 #define CONFIG_SYS_PCA953X_GPIO_VPX1            0x02 /* PU */
 322 #define CONFIG_SYS_PCA953X_GPIO_VPX2            0x04 /* PU */
 323 #define CONFIG_SYS_PCA953X_GPIO_VPX3            0x08 /* PU */
 324 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL        0x10 /* PD; I2C master source for FRU SEEPROM */
 325
 326 /*
 327  * General PCI
 328  * Memory space is mapped 1-1, but I/O space must start from 0.
 329  */
 330 /* PCIE1 - VPX P1 */
 331 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 332 #define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
 333 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x40000000      /* 1G */
 334 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 335 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe8000000
 336 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 337
 338 /* PCIE2 - PEX8518 */
 339 #define CONFIG_SYS_PCIE2_MEM_BUS        0xc0000000
 340 #define CONFIG_SYS_PCIE2_MEM_PHYS       CONFIG_SYS_PCIE2_MEM_BUS
 341 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000      /* 256M */
 342 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 343 #define CONFIG_SYS_PCIE2_IO_PHYS        0xe8800000
 344 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000      /* 8M */
 345
 346 /*
 347  * Networking options
 348  */
 349 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
 350 #define CONFIG_PHY_GIGE         1       /* Include GbE speed/duplex detection */
 351 #define CONFIG_TSEC_TBI
 352 #define CONFIG_MII              1       /* MII PHY management */
 353 #define CONFIG_MII_DEFAULT_TSEC 1       /* Allow unregistered phys */
 354 #define CONFIG_ETHPRIME         "eTSEC2"
 355
 356 /*
 357  * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
 358  * 1000mbps SGMII link
 359  */
 360 #define CONFIG_TSEC_TBICR_SETTINGS ( \
 361                 TBICR_PHY_RESET \
 362                 | TBICR_FULL_DUPLEX \
 363                 | TBICR_SPEED1_SET \
 364                 )
 365
 366 #define CONFIG_TSEC1            1
 367 #define CONFIG_TSEC1_NAME       "eTSEC1"
 368 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 369 #define TSEC1_PHY_ADDR          1
 370 #define TSEC1_PHYIDX            0
 371 #define CONFIG_HAS_ETH0
 372
 373 #define CONFIG_TSEC2            1
 374 #define CONFIG_TSEC2_NAME       "eTSEC2"
 375 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 376 #define TSEC2_PHY_ADDR          2
 377 #define TSEC2_PHYIDX            0
 378 #define CONFIG_HAS_ETH1
 379
 380 /*
 381  * Command configuration.
 382  */
 383 #define CONFIG_CMD_ASKENV
 384 #define CONFIG_CMD_DATE
 385 #define CONFIG_CMD_DHCP
 386 #define CONFIG_CMD_DS4510
 387 #define CONFIG_CMD_DS4510_INFO
 388 #define CONFIG_CMD_DTT
 389 #define CONFIG_CMD_EEPROM
 390 #define CONFIG_CMD_I2C
 391 #define CONFIG_CMD_JFFS2
 392 #define CONFIG_CMD_MII
 393 #define CONFIG_CMD_NAND
 394 #define CONFIG_CMD_PCA953X
 395 #define CONFIG_CMD_PCA953X_INFO
 396 #define CONFIG_CMD_PCI
 397 #define CONFIG_CMD_PCI_ENUM
 398 #define CONFIG_CMD_PING
 399 #define CONFIG_CMD_SNTP
 400 #define CONFIG_CMD_REGINFO
 401
 402 /*
 403  * Miscellaneous configurable options
 404  */
 405 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 406 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 407 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 408 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 409 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 410 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 411 #define CONFIG_CMDLINE_EDITING  1               /* add command line history     */
 412 #define CONFIG_AUTO_COMPLETE    1               /* add autocompletion support */
 413 #define CONFIG_LOADADDR         0x1000000       /* default location for tftp and bootm */
 414 #define CONFIG_BOOTDELAY        3               /* -1 disables auto-boot */
 415 #define CONFIG_PANIC_HANG                       /* do not reset board on panic */
 416 #define CONFIG_PREBOOT                          /* enable preboot variable */
 417 #define CONFIG_FIT              1
 418 #define CONFIG_FIT_VERBOSE      1
 419 #define CONFIG_INTEGRITY                        /* support booting INTEGRITY OS */
 420
 421 /*
 422  * For booting Linux, the board info and command line data
 423  * have to be in the first 16 MB of memory, since this is
 424  * the maximum mapped by the Linux kernel during initialization.
 425  */
 426 #define CONFIG_SYS_BOOTMAPSZ    (16 << 20)      /* Initial Memory map for Linux*/
 427 #define CONFIG_SYS_BOOTM_LEN    (16 << 20)      /* Increase max gunzip size */
 428
 429 /*
 430  * Environment Configuration
 431  */
 432 #define CONFIG_ENV_IS_IN_FLASH  1
 433 #define CONFIG_ENV_SECT_SIZE    0x20000         /* 128k (one sector) for env */
 434 #define CONFIG_ENV_SIZE         0x8000
 435 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
 436
 437 /*
 438  * Flash memory map:
 439  * fff80000 - ffffffff     Pri U-Boot (512 KB)
 440  * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
 441  * fff00000 - fff3ffff     Pri FDT (256KB)
 442  * fef00000 - ffefffff     Pri OS image (16MB)
 443  * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
 444  *
 445  * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
 446  * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
 447  * f7f00000 - f7f3ffff     Sec FDT (256KB)
 448  * f6f00000 - f7efffff     Sec OS image (16MB)
 449  * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
 450  */
 451 #define CONFIG_UBOOT1_ENV_ADDR  __stringify(0xfff80000)
 452 #define CONFIG_UBOOT2_ENV_ADDR  __stringify(0xf7f80000)
 453 #define CONFIG_FDT1_ENV_ADDR    __stringify(0xfff00000)
 454 #define CONFIG_FDT2_ENV_ADDR    __stringify(0xf7f00000)
 455 #define CONFIG_OS1_ENV_ADDR     __stringify(0xfef00000)
 456 #define CONFIG_OS2_ENV_ADDR     __stringify(0xf6f00000)
 457
 458 #define CONFIG_PROG_UBOOT1                                              \
 459         "$download_cmd $loadaddr $ubootfile; "                          \
 460         "if test $? -eq 0; then "                                       \
 461                 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "         \
 462                 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "               \
 463                 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "       \
 464                 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "          \
 465                 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "      \
 466                 "if test $? -ne 0; then "                               \
 467                         "echo PROGRAM FAILED; "                         \
 468                 "else; "                                                \
 469                         "echo PROGRAM SUCCEEDED; "                      \
 470                 "fi; "                                                  \
 471         "else; "                                                        \
 472                 "echo DOWNLOAD FAILED; "                                \
 473         "fi;"
 474
 475 #define CONFIG_PROG_UBOOT2                                              \
 476         "$download_cmd $loadaddr $ubootfile; "                          \
 477         "if test $? -eq 0; then "                                       \
 478                 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "         \
 479                 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "               \
 480                 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "       \
 481                 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "          \
 482                 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "      \
 483                 "if test $? -ne 0; then "                               \
 484                         "echo PROGRAM FAILED; "                         \
 485                 "else; "                                                \
 486                         "echo PROGRAM SUCCEEDED; "                      \
 487                 "fi; "                                                  \
 488         "else; "                                                        \
 489                 "echo DOWNLOAD FAILED; "                                \
 490         "fi;"
 491
 492 #define CONFIG_BOOT_OS_NET                                              \
 493         "$download_cmd $osaddr $osfile; "                               \
 494         "if test $? -eq 0; then "                                       \
 495                 "if test -n $fdtaddr; then "                            \
 496                         "$download_cmd $fdtaddr $fdtfile; "             \
 497                         "if test $? -eq 0; then "                       \
 498                                 "bootm $osaddr - $fdtaddr; "            \
 499                         "else; "                                        \
 500                                 "echo FDT DOWNLOAD FAILED; "            \
 501                         "fi; "                                          \
 502                 "else; "                                                \
 503                         "bootm $osaddr; "                               \
 504                 "fi; "                                                  \
 505         "else; "                                                        \
 506                 "echo OS DOWNLOAD FAILED; "                             \
 507         "fi;"
 508
 509 #define CONFIG_PROG_OS1                                                 \
 510         "$download_cmd $osaddr $osfile; "                               \
 511         "if test $? -eq 0; then "                                       \
 512                 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; "              \
 513                 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "        \
 514                 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "       \
 515                 "if test $? -ne 0; then "                               \
 516                         "echo OS PROGRAM FAILED; "                      \
 517                 "else; "                                                \
 518                         "echo OS PROGRAM SUCCEEDED; "                   \
 519                 "fi; "                                                  \
 520         "else; "                                                        \
 521                 "echo OS DOWNLOAD FAILED; "                             \
 522         "fi;"
 523
 524 #define CONFIG_PROG_OS2                                                 \
 525         "$download_cmd $osaddr $osfile; "                               \
 526         "if test $? -eq 0; then "                                       \
 527                 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; "              \
 528                 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "        \
 529                 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "       \
 530                 "if test $? -ne 0; then "                               \
 531                         "echo OS PROGRAM FAILED; "                      \
 532                 "else; "                                                \
 533                         "echo OS PROGRAM SUCCEEDED; "                   \
 534                 "fi; "                                                  \
 535         "else; "                                                        \
 536                 "echo OS DOWNLOAD FAILED; "                             \
 537         "fi;"
 538
 539 #define CONFIG_PROG_FDT1                                                \
 540         "$download_cmd $fdtaddr $fdtfile; "                             \
 541         "if test $? -eq 0; then "                                       \
 542                 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"              \
 543                 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "      \
 544                 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "     \
 545                 "if test $? -ne 0; then "                               \
 546                         "echo FDT PROGRAM FAILED; "                     \
 547                 "else; "                                                \
 548                         "echo FDT PROGRAM SUCCEEDED; "                  \
 549                 "fi; "                                                  \
 550         "else; "                                                        \
 551                 "echo FDT DOWNLOAD FAILED; "                            \
 552         "fi;"
 553
 554 #define CONFIG_PROG_FDT2                                                \
 555         "$download_cmd $fdtaddr $fdtfile; "                             \
 556         "if test $? -eq 0; then "                                       \
 557                 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"              \
 558                 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "      \
 559                 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "     \
 560                 "if test $? -ne 0; then "                               \
 561                         "echo FDT PROGRAM FAILED; "                     \
 562                 "else; "                                                \
 563                         "echo FDT PROGRAM SUCCEEDED; "                  \
 564                 "fi; "                                                  \
 565         "else; "                                                        \
 566                 "echo FDT DOWNLOAD FAILED; "                            \
 567         "fi;"
 568
 569 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 570         "autoload=yes\0"                                                \
 571         "download_cmd=tftp\0"                                           \
 572         "console_args=console=ttyS0,115200\0"                           \
 573         "root_args=root=/dev/nfs rw\0"                                  \
 574         "misc_args=ip=on\0"                                             \
 575         "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 576         "bootfile=/home/user/file\0"                                    \
 577         "osfile=/home/user/board.uImage\0"                              \
 578         "fdtfile=/home/user/board.dtb\0"                                \
 579         "ubootfile=/home/user/u-boot.bin\0"                             \
 580         "fdtaddr=c00000\0"                                              \
 581         "osaddr=0x1000000\0"                                            \
 582         "loadaddr=0x1000000\0"                                          \
 583         "prog_uboot1="CONFIG_PROG_UBOOT1"\0"                            \
 584         "prog_uboot2="CONFIG_PROG_UBOOT2"\0"                            \
 585         "prog_os1="CONFIG_PROG_OS1"\0"                                  \
 586         "prog_os2="CONFIG_PROG_OS2"\0"                                  \
 587         "prog_fdt1="CONFIG_PROG_FDT1"\0"                                \
 588         "prog_fdt2="CONFIG_PROG_FDT2"\0"                                \
 589         "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"          \
 590         "bootcmd_flash1=run set_bootargs; "                             \
 591                 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
 592         "bootcmd_flash2=run set_bootargs; "                             \
 593                 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
 594         "bootcmd=run bootcmd_flash1\0"
 595 #endif  /* __CONFIG_H */