2 * (C) Copyright 2012 Michal Simek <monstr@monstr.eu>
3 * (C) Copyright 2013 - 2018 Xilinx, Inc.
5 * Common configuration options for all Zynq boards.
7 * SPDX-License-Identifier: GPL-2.0+
10 #ifndef __CONFIG_ZYNQ_COMMON_H
11 #define __CONFIG_ZYNQ_COMMON_H
14 #ifndef CONFIG_CPU_FREQ_HZ
15 # define CONFIG_CPU_FREQ_HZ 800000000
19 #define CONFIG_SYS_L2CACHE_OFF
20 #ifndef CONFIG_SYS_L2CACHE_OFF
21 # define CONFIG_SYS_L2_PL310
22 # define CONFIG_SYS_PL310_BASE 0xf8f02000
25 #define ZYNQ_SCUTIMER_BASEADDR 0xF8F00600
26 #define CONFIG_SYS_TIMERBASE ZYNQ_SCUTIMER_BASEADDR
27 #define CONFIG_SYS_TIMER_COUNTS_DOWN
28 #define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4)
31 /* The following table includes the supported baudrates */
32 #define CONFIG_SYS_BAUDRATE_TABLE \
33 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
35 #define CONFIG_ARM_DCC
38 #if defined(CONFIG_ZYNQ_GEM)
40 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
41 # define CONFIG_BOOTP_MAY_FAIL
45 #ifdef CONFIG_ZYNQ_SPI
49 #ifdef CONFIG_ZYNQ_QSPI
50 # define CONFIG_SF_DEFAULT_SPEED 30000000
51 # define CONFIG_SPI_FLASH_ISSI
55 #ifdef CONFIG_MTD_NOR_FLASH
56 # define CONFIG_SYS_FLASH_BASE 0xE2000000
57 # define CONFIG_SYS_FLASH_SIZE (16 * 1024 * 1024)
58 # define CONFIG_SYS_MAX_FLASH_BANKS 1
59 # define CONFIG_SYS_MAX_FLASH_SECT 512
60 # define CONFIG_SYS_FLASH_ERASE_TOUT 1000
61 # define CONFIG_SYS_FLASH_WRITE_TOUT 5000
62 # define CONFIG_FLASH_SHOW_PROGRESS 10
63 # define CONFIG_SYS_FLASH_CFI
64 # undef CONFIG_SYS_FLASH_EMPTY_INFO
65 # define CONFIG_FLASH_CFI_DRIVER
66 # undef CONFIG_SYS_FLASH_PROTECTION
67 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
70 #ifdef CONFIG_NAND_ZYNQ
71 #define CONFIG_SYS_MAX_NAND_DEVICE 1
72 #define CONFIG_SYS_NAND_ONFI_DETECTION
73 #define CONFIG_MTD_DEVICE
76 #ifdef CONFIG_USB_EHCI_ZYNQ
77 # define CONFIG_EHCI_IS_TDI
79 # define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x600000
80 # define DFU_DEFAULT_POLL_TIMEOUT 300
81 # define CONFIG_USB_CABLE_CHECK
82 # define CONFIG_THOR_RESET_OFF
83 # define DFU_ALT_INFO_RAM \
86 "${kernel_image} ram 0x3000000 0x500000\\\\;" \
87 "${devicetree_image} ram 0x2A00000 0x20000\\\\;" \
88 "${ramdisk_image} ram 0x2000000 0x600000\0" \
89 "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
90 "thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
92 # if defined(CONFIG_MMC_SDHCI_ZYNQ)
93 # define DFU_ALT_INFO_MMC \
96 "${kernel_image} fat 0 1\\\\;" \
97 "${devicetree_image} fat 0 1\\\\;" \
98 "${ramdisk_image} fat 0 1\0" \
99 "dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \
100 "thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0"
102 # define DFU_ALT_INFO \
106 # define DFU_ALT_INFO \
111 #if !defined(DFU_ALT_INFO)
112 # define DFU_ALT_INFO
116 #if defined(CONFIG_SYS_I2C_ZYNQ)
117 # define CONFIG_SYS_I2C
121 #ifdef CONFIG_ZYNQ_EEPROM
122 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
123 # define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
124 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
125 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
126 # define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */
129 /* Total Size of Environment Sector */
130 #ifndef CONFIG_ENV_SIZE
131 # define CONFIG_ENV_SIZE (128 << 10)
134 /* Allow to overwrite serial and ethaddr */
135 #define CONFIG_ENV_OVERWRITE
138 #ifndef CONFIG_ENV_IS_NOWHERE
139 # define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
140 # ifndef CONFIG_ENV_OFFSET
141 # define CONFIG_ENV_OFFSET 0xE0000
145 /* enable preboot to be loaded before CONFIG_BOOTDELAY */
146 #define CONFIG_PREBOOT
148 /* Boot configuration */
149 #define CONFIG_SYS_LOAD_ADDR 0 /* default? */
151 /* Distro boot enablement */
153 #ifdef CONFIG_SPL_BUILD
157 #ifdef CONFIG_CMD_MMC
158 #define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
160 #define BOOT_TARGET_DEVICES_MMC(func)
163 #ifdef CONFIG_CMD_USB
164 #define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
166 #define BOOT_TARGET_DEVICES_USB(func)
169 #if defined(CONFIG_CMD_PXE) && defined(CONFIG_CMD_DHCP)
170 #define BOOT_TARGET_DEVICES_PXE(func) func(PXE, pxe, na)
172 #define BOOT_TARGET_DEVICES_PXE(func)
175 #if defined(CONFIG_CMD_DHCP)
176 #define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
178 #define BOOT_TARGET_DEVICES_DHCP(func)
181 #define BOOT_TARGET_DEVICES(func) \
182 BOOT_TARGET_DEVICES_MMC(func) \
183 BOOT_TARGET_DEVICES_USB(func) \
184 BOOT_TARGET_DEVICES_PXE(func) \
185 BOOT_TARGET_DEVICES_DHCP(func)
187 #include <config_distro_bootcmd.h>
188 #endif /* CONFIG_SPL_BUILD */
190 /* Default environment */
191 #ifndef CONFIG_EXTRA_ENV_SETTINGS
192 #define CONFIG_EXTRA_ENV_SETTINGS \
193 "fit_image=fit.itb\0" \
194 "load_addr=0x2000000\0" \
195 "fit_size=0x800000\0" \
196 "flash_off=0x100000\0" \
197 "nor_flash_off=0xE2100000\0" \
198 "fdt_high=0x20000000\0" \
199 "initrd_high=0x20000000\0" \
200 "loadbootenv_addr=0x2000000\0" \
201 "fdt_addr_r=0x1f00000\0" \
202 "pxefile_addr_r=0x2000000\0" \
203 "kernel_addr_r=0x2000000\0" \
204 "scriptaddr=0x3000000\0" \
205 "ramdisk_addr_r=0x3100000\0" \
206 "bootenv=uEnv.txt\0" \
207 "bootenv_dev=mmc\0" \
208 "loadbootenv=load ${bootenv_dev} 0 ${loadbootenv_addr} ${bootenv}\0" \
209 "importbootenv=echo Importing environment from ${bootenv_dev} ...; " \
210 "env import -t ${loadbootenv_addr} $filesize\0" \
211 "bootenv_existence_test=test -e ${bootenv_dev} 0 /${bootenv}\0" \
212 "setbootenv=if env run bootenv_existence_test; then " \
213 "if env run loadbootenv; then " \
214 "env run importbootenv; " \
217 "sd_loadbootenv=set bootenv_dev mmc && " \
218 "run setbootenv \0" \
219 "usb_loadbootenv=set bootenv_dev usb && usb start && run setbootenv \0" \
220 "preboot=if test $modeboot = sdboot; then " \
221 "run sd_loadbootenv; " \
222 "echo Checking if uenvcmd is set ...; " \
223 "if test -n $uenvcmd; then " \
224 "echo Running uenvcmd ...; " \
228 "norboot=echo Copying FIT from NOR flash to RAM... && " \
229 "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
230 "bootm ${load_addr}\0" \
231 "sdboot=echo Copying FIT from SD to RAM... && " \
232 "load mmc 0 ${load_addr} ${fit_image} && " \
233 "bootm ${load_addr}\0" \
234 "jtagboot=echo TFTPing FIT to RAM... && " \
235 "tftpboot ${load_addr} ${fit_image} && " \
236 "bootm ${load_addr}\0" \
237 "usbboot=if usb start; then " \
238 "echo Copying FIT from USB to RAM... && " \
239 "load usb 0 ${load_addr} ${fit_image} && " \
240 "bootm ${load_addr}; fi\0" \
245 /* Miscellaneous configurable options */
247 #define CONFIG_CLOCKS
248 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */
250 #ifndef CONFIG_NR_DRAM_BANKS
251 # define CONFIG_NR_DRAM_BANKS 1
254 #define CONFIG_SYS_MEMTEST_START 0
255 #define CONFIG_SYS_MEMTEST_END 0x1000
257 #define CONFIG_SYS_MALLOC_LEN 0x1400000
259 #define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
260 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000
261 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
262 CONFIG_SYS_INIT_RAM_SIZE - \
263 GENERATED_GBL_DATA_SIZE)
267 #define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */
269 /* Extend size of kernel image for uncompression */
270 #define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024)
272 /* Boot FreeBSD/vxWorks from an ELF image */
273 #define CONFIG_SYS_MMC_MAX_DEVICE 1
275 #define CONFIG_SYS_LDSCRIPT "arch/arm/mach-zynq/u-boot.lds"
282 #ifdef CONFIG_MMC_SDHCI_ZYNQ
283 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
284 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
287 /* Disable dcache for SPL just for sure */
288 #ifdef CONFIG_SPL_BUILD
289 #define CONFIG_SYS_DCACHE_OFF
292 /* Address in RAM where the parameters must be copied by SPL. */
293 #define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000
295 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "system.dtb"
296 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
298 /* Not using MMC raw mode - just for compilation purpose */
299 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0
300 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0
301 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0
303 /* qspi mode is working fine */
304 #ifdef CONFIG_ZYNQ_QSPI
305 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000
306 #define CONFIG_SYS_SPI_ARGS_OFFS 0x200000
307 #define CONFIG_SYS_SPI_ARGS_SIZE 0x80000
308 #define CONFIG_SYS_SPI_KERNEL_OFFS (CONFIG_SYS_SPI_ARGS_OFFS + \
309 CONFIG_SYS_SPI_ARGS_SIZE)
312 /* for booting directly linux */
314 /* SP location before relocation, must use scratch RAM */
315 #define CONFIG_SPL_TEXT_BASE 0x0
317 /* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
318 #define CONFIG_SPL_MAX_SIZE 0x30000
320 /* On the top of OCM space */
321 #define CONFIG_SYS_SPL_MALLOC_START CONFIG_SPL_STACK_R_ADDR
322 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x2000000
325 * SPL stack position - and stack goes down
326 * 0xfffffe00 is used for putting wfi loop.
327 * Set it up as limit for now.
329 #define CONFIG_SPL_STACK 0xfffffe00
332 #define CONFIG_SPL_BSS_START_ADDR 0x100000
333 #define CONFIG_SPL_BSS_MAX_SIZE 0x100000
335 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
337 #endif /* __CONFIG_ZYNQ_COMMON_H */