2 * Copyright 2008,2010 Freescale Semiconductor, Inc
5 * Based (loosely) on the Linux code
7 * SPDX-License-Identifier: GPL-2.0+
13 #include <linux/list.h>
14 #include <linux/compiler.h>
17 /* SD/MMC version bits; 8 flags, 8 major, 8 minor, 8 change */
18 #define SD_VERSION_SD (1U << 31)
19 #define MMC_VERSION_MMC (1U << 30)
21 #define MAKE_SDMMC_VERSION(a, b, c) \
22 ((((u32)(a)) << 16) | ((u32)(b) << 8) | (u32)(c))
23 #define MAKE_SD_VERSION(a, b, c) \
24 (SD_VERSION_SD | MAKE_SDMMC_VERSION(a, b, c))
25 #define MAKE_MMC_VERSION(a, b, c) \
26 (MMC_VERSION_MMC | MAKE_SDMMC_VERSION(a, b, c))
28 #define EXTRACT_SDMMC_MAJOR_VERSION(x) \
29 (((u32)(x) >> 16) & 0xff)
30 #define EXTRACT_SDMMC_MINOR_VERSION(x) \
31 (((u32)(x) >> 8) & 0xff)
32 #define EXTRACT_SDMMC_CHANGE_VERSION(x) \
35 #define SD_VERSION_3 MAKE_SD_VERSION(3, 0, 0)
36 #define SD_VERSION_2 MAKE_SD_VERSION(2, 0, 0)
37 #define SD_VERSION_1_0 MAKE_SD_VERSION(1, 0, 0)
38 #define SD_VERSION_1_10 MAKE_SD_VERSION(1, 10, 0)
40 #define MMC_VERSION_UNKNOWN MAKE_MMC_VERSION(0, 0, 0)
41 #define MMC_VERSION_1_2 MAKE_MMC_VERSION(1, 2, 0)
42 #define MMC_VERSION_1_4 MAKE_MMC_VERSION(1, 4, 0)
43 #define MMC_VERSION_2_2 MAKE_MMC_VERSION(2, 2, 0)
44 #define MMC_VERSION_3 MAKE_MMC_VERSION(3, 0, 0)
45 #define MMC_VERSION_4 MAKE_MMC_VERSION(4, 0, 0)
46 #define MMC_VERSION_4_1 MAKE_MMC_VERSION(4, 1, 0)
47 #define MMC_VERSION_4_2 MAKE_MMC_VERSION(4, 2, 0)
48 #define MMC_VERSION_4_3 MAKE_MMC_VERSION(4, 3, 0)
49 #define MMC_VERSION_4_41 MAKE_MMC_VERSION(4, 4, 1)
50 #define MMC_VERSION_4_5 MAKE_MMC_VERSION(4, 5, 0)
51 #define MMC_VERSION_5_0 MAKE_MMC_VERSION(5, 0, 0)
52 #define MMC_VERSION_5_1 MAKE_MMC_VERSION(5, 1, 0)
54 #define MMC_MODE_HS (1 << 0)
55 #define MMC_MODE_HS_52MHz (1 << 1)
56 #define MMC_MODE_4BIT (1 << 2)
57 #define MMC_MODE_8BIT (1 << 3)
58 #define MMC_MODE_SPI (1 << 4)
59 #define MMC_MODE_DDR_52MHz (1 << 5)
61 #define SD_DATA_4BIT 0x00040000
63 #define IS_SD(x) ((x)->version & SD_VERSION_SD)
64 #define IS_MMC(x) ((x)->version & MMC_VERSION_MMC)
66 #define MMC_DATA_READ 1
67 #define MMC_DATA_WRITE 2
69 #define NO_CARD_ERR -16 /* No SD/MMC card inserted */
70 #define UNUSABLE_ERR -17 /* Unusable Card */
71 #define COMM_ERR -18 /* Communications Error */
73 #define SWITCH_ERR -20 /* Card reports failure to switch mode */
75 #define MMC_CMD_GO_IDLE_STATE 0
76 #define MMC_CMD_SEND_OP_COND 1
77 #define MMC_CMD_ALL_SEND_CID 2
78 #define MMC_CMD_SET_RELATIVE_ADDR 3
79 #define MMC_CMD_SET_DSR 4
80 #define MMC_CMD_SWITCH 6
81 #define MMC_CMD_SELECT_CARD 7
82 #define MMC_CMD_SEND_EXT_CSD 8
83 #define MMC_CMD_SEND_CSD 9
84 #define MMC_CMD_SEND_CID 10
85 #define MMC_CMD_STOP_TRANSMISSION 12
86 #define MMC_CMD_SEND_STATUS 13
87 #define MMC_CMD_SET_BLOCKLEN 16
88 #define MMC_CMD_READ_SINGLE_BLOCK 17
89 #define MMC_CMD_READ_MULTIPLE_BLOCK 18
90 #define MMC_CMD_SET_BLOCK_COUNT 23
91 #define MMC_CMD_WRITE_SINGLE_BLOCK 24
92 #define MMC_CMD_WRITE_MULTIPLE_BLOCK 25
93 #define MMC_CMD_ERASE_GROUP_START 35
94 #define MMC_CMD_ERASE_GROUP_END 36
95 #define MMC_CMD_ERASE 38
96 #define MMC_CMD_APP_CMD 55
97 #define MMC_CMD_SPI_READ_OCR 58
98 #define MMC_CMD_SPI_CRC_ON_OFF 59
99 #define MMC_CMD_RES_MAN 62
101 #define MMC_CMD62_ARG1 0xefac62ec
102 #define MMC_CMD62_ARG2 0xcbaea7
105 #define SD_CMD_SEND_RELATIVE_ADDR 3
106 #define SD_CMD_SWITCH_FUNC 6
107 #define SD_CMD_SEND_IF_COND 8
108 #define SD_CMD_SWITCH_UHS18V 11
110 #define SD_CMD_APP_SET_BUS_WIDTH 6
111 #define SD_CMD_ERASE_WR_BLK_START 32
112 #define SD_CMD_ERASE_WR_BLK_END 33
113 #define SD_CMD_APP_SEND_OP_COND 41
114 #define SD_CMD_APP_SEND_SCR 51
116 /* SCR definitions in different words */
117 #define SD_HIGHSPEED_BUSY 0x00020000
118 #define SD_HIGHSPEED_SUPPORTED 0x00020000
120 #define OCR_BUSY 0x80000000
121 #define OCR_HCS 0x40000000
122 #define OCR_VOLTAGE_MASK 0x007FFF80
123 #define OCR_ACCESS_MODE 0x60000000
125 #define MMC_ERASE_ARG 0x00000000
126 #define MMC_SECURE_ERASE_ARG 0x80000000
127 #define MMC_TRIM_ARG 0x00000001
128 #define MMC_DISCARD_ARG 0x00000003
129 #define MMC_SECURE_TRIM1_ARG 0x80000001
130 #define MMC_SECURE_TRIM2_ARG 0x80008000
132 #define MMC_STATUS_MASK (~0x0206BF7F)
133 #define MMC_STATUS_SWITCH_ERROR (1 << 7)
134 #define MMC_STATUS_RDY_FOR_DATA (1 << 8)
135 #define MMC_STATUS_CURR_STATE (0xf << 9)
136 #define MMC_STATUS_ERROR (1 << 19)
138 #define MMC_STATE_PRG (7 << 9)
140 #define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */
141 #define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */
142 #define MMC_VDD_21_22 0x00000200 /* VDD voltage 2.1 ~ 2.2 */
143 #define MMC_VDD_22_23 0x00000400 /* VDD voltage 2.2 ~ 2.3 */
144 #define MMC_VDD_23_24 0x00000800 /* VDD voltage 2.3 ~ 2.4 */
145 #define MMC_VDD_24_25 0x00001000 /* VDD voltage 2.4 ~ 2.5 */
146 #define MMC_VDD_25_26 0x00002000 /* VDD voltage 2.5 ~ 2.6 */
147 #define MMC_VDD_26_27 0x00004000 /* VDD voltage 2.6 ~ 2.7 */
148 #define MMC_VDD_27_28 0x00008000 /* VDD voltage 2.7 ~ 2.8 */
149 #define MMC_VDD_28_29 0x00010000 /* VDD voltage 2.8 ~ 2.9 */
150 #define MMC_VDD_29_30 0x00020000 /* VDD voltage 2.9 ~ 3.0 */
151 #define MMC_VDD_30_31 0x00040000 /* VDD voltage 3.0 ~ 3.1 */
152 #define MMC_VDD_31_32 0x00080000 /* VDD voltage 3.1 ~ 3.2 */
153 #define MMC_VDD_32_33 0x00100000 /* VDD voltage 3.2 ~ 3.3 */
154 #define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */
155 #define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */
156 #define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */
158 #define MMC_SWITCH_MODE_CMD_SET 0x00 /* Change the command set */
159 #define MMC_SWITCH_MODE_SET_BITS 0x01 /* Set bits in EXT_CSD byte
160 addressed by index which are
162 #define MMC_SWITCH_MODE_CLEAR_BITS 0x02 /* Clear bits in EXT_CSD byte
163 addressed by index, which are
165 #define MMC_SWITCH_MODE_WRITE_BYTE 0x03 /* Set target byte to value */
167 #define SD_SWITCH_CHECK 0
168 #define SD_SWITCH_SWITCH 1
173 #define EXT_CSD_ENH_START_ADDR 136 /* R/W */
174 #define EXT_CSD_ENH_SIZE_MULT 140 /* R/W */
175 #define EXT_CSD_GP_SIZE_MULT 143 /* R/W */
176 #define EXT_CSD_PARTITION_SETTING 155 /* R/W */
177 #define EXT_CSD_PARTITIONS_ATTRIBUTE 156 /* R/W */
178 #define EXT_CSD_MAX_ENH_SIZE_MULT 157 /* R */
179 #define EXT_CSD_PARTITIONING_SUPPORT 160 /* RO */
180 #define EXT_CSD_RST_N_FUNCTION 162 /* R/W */
181 #define EXT_CSD_WR_REL_PARAM 166 /* R */
182 #define EXT_CSD_WR_REL_SET 167 /* R/W */
183 #define EXT_CSD_RPMB_MULT 168 /* RO */
184 #define EXT_CSD_ERASE_GROUP_DEF 175 /* R/W */
185 #define EXT_CSD_BOOT_BUS_WIDTH 177
186 #define EXT_CSD_PART_CONF 179 /* R/W */
187 #define EXT_CSD_BUS_WIDTH 183 /* R/W */
188 #define EXT_CSD_HS_TIMING 185 /* R/W */
189 #define EXT_CSD_REV 192 /* RO */
190 #define EXT_CSD_CARD_TYPE 196 /* RO */
191 #define EXT_CSD_SEC_CNT 212 /* RO, 4 bytes */
192 #define EXT_CSD_HC_WP_GRP_SIZE 221 /* RO */
193 #define EXT_CSD_HC_ERASE_GRP_SIZE 224 /* RO */
194 #define EXT_CSD_BOOT_MULT 226 /* RO */
197 * EXT_CSD field definitions
200 #define EXT_CSD_CMD_SET_NORMAL (1 << 0)
201 #define EXT_CSD_CMD_SET_SECURE (1 << 1)
202 #define EXT_CSD_CMD_SET_CPSECURE (1 << 2)
204 #define EXT_CSD_CARD_TYPE_26 (1 << 0) /* Card can run at 26MHz */
205 #define EXT_CSD_CARD_TYPE_52 (1 << 1) /* Card can run at 52MHz */
206 #define EXT_CSD_CARD_TYPE_DDR_1_8V (1 << 2)
207 #define EXT_CSD_CARD_TYPE_DDR_1_2V (1 << 3)
208 #define EXT_CSD_CARD_TYPE_DDR_52 (EXT_CSD_CARD_TYPE_DDR_1_8V \
209 | EXT_CSD_CARD_TYPE_DDR_1_2V)
211 #define EXT_CSD_BUS_WIDTH_1 0 /* Card is in 1 bit mode */
212 #define EXT_CSD_BUS_WIDTH_4 1 /* Card is in 4 bit mode */
213 #define EXT_CSD_BUS_WIDTH_8 2 /* Card is in 8 bit mode */
214 #define EXT_CSD_DDR_BUS_WIDTH_4 5 /* Card is in 4 bit DDR mode */
215 #define EXT_CSD_DDR_BUS_WIDTH_8 6 /* Card is in 8 bit DDR mode */
217 #define EXT_CSD_BOOT_ACK_ENABLE (1 << 6)
218 #define EXT_CSD_BOOT_PARTITION_ENABLE (1 << 3)
219 #define EXT_CSD_PARTITION_ACCESS_ENABLE (1 << 0)
220 #define EXT_CSD_PARTITION_ACCESS_DISABLE (0 << 0)
222 #define EXT_CSD_BOOT_ACK(x) (x << 6)
223 #define EXT_CSD_BOOT_PART_NUM(x) (x << 3)
224 #define EXT_CSD_PARTITION_ACCESS(x) (x << 0)
226 #define EXT_CSD_BOOT_BUS_WIDTH_MODE(x) (x << 3)
227 #define EXT_CSD_BOOT_BUS_WIDTH_RESET(x) (x << 2)
228 #define EXT_CSD_BOOT_BUS_WIDTH_WIDTH(x) (x)
230 #define EXT_CSD_PARTITION_SETTING_COMPLETED (1 << 0)
232 #define EXT_CSD_ENH_USR (1 << 0) /* user data area is enhanced */
233 #define EXT_CSD_ENH_GP(x) (1 << ((x)+1)) /* GP part (x+1) is enhanced */
235 #define EXT_CSD_HS_CTRL_REL (1 << 0) /* host controlled WR_REL_SET */
237 #define EXT_CSD_WR_DATA_REL_USR (1 << 0) /* user data area WR_REL */
238 #define EXT_CSD_WR_DATA_REL_GP(x) (1 << ((x)+1)) /* GP part (x+1) WR_REL */
240 #define R1_ILLEGAL_COMMAND (1 << 22)
241 #define R1_APP_CMD (1 << 5)
243 #define MMC_RSP_PRESENT (1 << 0)
244 #define MMC_RSP_136 (1 << 1) /* 136 bit response */
245 #define MMC_RSP_CRC (1 << 2) /* expect valid crc */
246 #define MMC_RSP_BUSY (1 << 3) /* card may send busy */
247 #define MMC_RSP_OPCODE (1 << 4) /* response contains opcode */
249 #define MMC_RSP_NONE (0)
250 #define MMC_RSP_R1 (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
251 #define MMC_RSP_R1b (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE| \
253 #define MMC_RSP_R2 (MMC_RSP_PRESENT|MMC_RSP_136|MMC_RSP_CRC)
254 #define MMC_RSP_R3 (MMC_RSP_PRESENT)
255 #define MMC_RSP_R4 (MMC_RSP_PRESENT)
256 #define MMC_RSP_R5 (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
257 #define MMC_RSP_R6 (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
258 #define MMC_RSP_R7 (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
260 #define MMCPART_NOAVAILABLE (0xff)
261 #define PART_ACCESS_MASK (0x7)
262 #define PART_SUPPORT (0x1)
263 #define ENHNCD_SUPPORT (0x2)
264 #define PART_ENH_ATTRIB (0x1f)
266 /* Maximum block size for MMC */
267 #define MMC_MAX_BLOCK_LEN 512
269 /* The number of MMC physical partitions. These consist of:
270 * boot partitions (2), general purpose partitions (4) in MMC v4.4.
272 #define MMC_NUM_BOOT_PARTITION 2
273 #define MMC_PART_RPMB 3 /* RPMB partition number */
275 /* Driver model support */
278 * struct mmc_uclass_priv - Holds information about a device used by the uclass
280 struct mmc_uclass_priv {
285 * mmc_get_mmc_dev() - get the MMC struct pointer for a device
287 * Provided that the device is already probed and ready for use, this value
291 * @return associated mmc struct pointer if available, else NULL
293 struct mmc *mmc_get_mmc_dev(struct udevice *dev);
295 /* End of driver model support */
316 const char *src; /* src buffers don't get written to */
326 #ifdef CONFIG_DM_MMC_OPS
329 * send_cmd() - Send a command to the MMC device
331 * @dev: Device to receive the command
332 * @cmd: Command to send
333 * @data: Additional data to send/receive
334 * @return 0 if OK, -ve on error
336 int (*send_cmd)(struct udevice *dev, struct mmc_cmd *cmd,
337 struct mmc_data *data);
340 * set_ios() - Set the I/O speed/width for an MMC device
342 * @dev: Device to update
343 * @return 0 if OK, -ve on error
345 int (*set_ios)(struct udevice *dev);
348 * get_cd() - See whether a card is present
350 * @dev: Device to check
351 * @return 0 if not present, 1 if present, -ve on error
353 int (*get_cd)(struct udevice *dev);
356 * get_wp() - See whether a card has write-protect enabled
358 * @dev: Device to check
359 * @return 0 if write-enabled, 1 if write-protected, -ve on error
361 int (*get_wp)(struct udevice *dev);
364 #define mmc_get_ops(dev) ((struct dm_mmc_ops *)(dev)->driver->ops)
366 int dm_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
367 struct mmc_data *data);
368 int dm_mmc_set_ios(struct udevice *dev);
369 int dm_mmc_get_cd(struct udevice *dev);
370 int dm_mmc_get_wp(struct udevice *dev);
372 /* Transition functions for compatibility */
373 int mmc_set_ios(struct mmc *mmc);
374 int mmc_getcd(struct mmc *mmc);
375 int mmc_getwp(struct mmc *mmc);
379 int (*send_cmd)(struct mmc *mmc,
380 struct mmc_cmd *cmd, struct mmc_data *data);
381 void (*set_ios)(struct mmc *mmc);
382 int (*init)(struct mmc *mmc);
383 int (*getcd)(struct mmc *mmc);
384 int (*getwp)(struct mmc *mmc);
390 #ifndef CONFIG_DM_MMC_OPS
391 const struct mmc_ops *ops;
398 unsigned char part_type;
402 * With CONFIG_DM_MMC enabled, struct mmc can be accessed from the MMC device
403 * with mmc_get_mmc_dev().
405 * TODO struct mmc should be in mmc_private but it's hard to fix right now
409 struct list_head link;
411 const struct mmc_config *cfg; /* provided configuration */
433 uint erase_grp_size; /* in 512-byte sectors */
434 uint hc_wp_grp_size; /* in 512-byte sectors */
443 struct blk_desc block_dev;
445 char op_cond_pending; /* 1 if we are waiting on an op_cond command */
446 char init_in_progress; /* 1 if we have done mmc_start_init() */
447 char preinit; /* start init as early as possible */
450 struct udevice *dev; /* Device for this MMC controller */
454 struct mmc_hwpart_conf {
456 uint enh_start; /* in 512-byte sectors */
457 uint enh_size; /* in 512-byte sectors, if 0 no enh area */
458 unsigned wr_rel_change : 1;
459 unsigned wr_rel_set : 1;
462 uint size; /* in 512-byte sectors */
463 unsigned enhanced : 1;
464 unsigned wr_rel_change : 1;
465 unsigned wr_rel_set : 1;
469 enum mmc_hwpart_conf_mode {
470 MMC_HWPART_CONF_CHECK,
472 MMC_HWPART_CONF_COMPLETE,
475 struct mmc *mmc_create(const struct mmc_config *cfg, void *priv);
478 * mmc_bind() - Set up a new MMC device ready for probing
480 * A child block device is bound with the IF_TYPE_MMC interface type. This
481 * allows the device to be used with CONFIG_BLK
483 * @dev: MMC device to set up
485 * @cfg: MMC configuration
486 * @return 0 if OK, -ve on error
488 int mmc_bind(struct udevice *dev, struct mmc *mmc,
489 const struct mmc_config *cfg);
490 void mmc_destroy(struct mmc *mmc);
493 * mmc_unbind() - Unbind a MMC device's child block device
496 * @return 0 if OK, -ve on error
498 int mmc_unbind(struct udevice *dev);
499 int mmc_initialize(bd_t *bis);
500 int mmc_init(struct mmc *mmc);
501 int mmc_read(struct mmc *mmc, u64 src, uchar *dst, int size);
502 void mmc_set_clock(struct mmc *mmc, uint clock);
503 struct mmc *find_mmc_device(int dev_num);
504 int mmc_set_dev(int dev_num);
505 void print_mmc_devices(char separator);
508 * get_mmc_num() - get the total MMC device number
510 * @return 0 if there is no MMC device, else the number of devices
512 int get_mmc_num(void);
513 int mmc_hwpart_config(struct mmc *mmc, const struct mmc_hwpart_conf *conf,
514 enum mmc_hwpart_conf_mode mode);
516 #ifndef CONFIG_DM_MMC_OPS
517 int mmc_getcd(struct mmc *mmc);
518 int board_mmc_getcd(struct mmc *mmc);
519 int mmc_getwp(struct mmc *mmc);
520 int board_mmc_getwp(struct mmc *mmc);
523 int mmc_set_dsr(struct mmc *mmc, u16 val);
524 /* Function to change the size of boot partition and rpmb partitions */
525 int mmc_boot_partition_size_change(struct mmc *mmc, unsigned long bootsize,
526 unsigned long rpmbsize);
527 /* Function to modify the PARTITION_CONFIG field of EXT_CSD */
528 int mmc_set_part_conf(struct mmc *mmc, u8 ack, u8 part_num, u8 access);
529 /* Function to modify the BOOT_BUS_WIDTH field of EXT_CSD */
530 int mmc_set_boot_bus_width(struct mmc *mmc, u8 width, u8 reset, u8 mode);
531 /* Function to modify the RST_n_FUNCTION field of EXT_CSD */
532 int mmc_set_rst_n_function(struct mmc *mmc, u8 enable);
533 /* Functions to read / write the RPMB partition */
534 int mmc_rpmb_set_key(struct mmc *mmc, void *key);
535 int mmc_rpmb_get_counter(struct mmc *mmc, unsigned long *counter);
536 int mmc_rpmb_read(struct mmc *mmc, void *addr, unsigned short blk,
537 unsigned short cnt, unsigned char *key);
538 int mmc_rpmb_write(struct mmc *mmc, void *addr, unsigned short blk,
539 unsigned short cnt, unsigned char *key);
541 * Start device initialization and return immediately; it does not block on
542 * polling OCR (operation condition register) status. Then you should call
543 * mmc_init, which would block on polling OCR status and complete the device
546 * @param mmc Pointer to a MMC device struct
547 * @return 0 on success, IN_PROGRESS on waiting for OCR status, <0 on error.
549 int mmc_start_init(struct mmc *mmc);
552 * Set preinit flag of mmc device.
554 * This will cause the device to be pre-inited during mmc_initialize(),
555 * which may save boot time if the device is not accessed until later.
556 * Some eMMC devices take 200-300ms to init, but unfortunately they
557 * must be sent a series of commands to even get them to start preparing
560 * @param mmc Pointer to a MMC device struct
561 * @param preinit preinit flag value
563 void mmc_set_preinit(struct mmc *mmc, int preinit);
565 #ifdef CONFIG_MMC_SPI
566 #define mmc_host_is_spi(mmc) ((mmc)->cfg->host_caps & MMC_MODE_SPI)
568 #define mmc_host_is_spi(mmc) 0
570 struct mmc *mmc_spi_init(uint bus, uint cs, uint speed, uint mode);
572 void board_mmc_power_init(void);
573 int board_mmc_init(bd_t *bis);
574 int cpu_mmc_init(bd_t *bis);
575 int mmc_get_env_addr(struct mmc *mmc, int copy, u32 *env_addr);
576 int mmc_get_env_dev(void);
578 struct pci_device_id;
581 * pci_mmc_init() - set up PCI MMC devices
583 * This finds all the matching PCI IDs and sets them up as MMC devices.
585 * @name: Name to use for devices
586 * @mmc_supported: PCI IDs to search for, terminated by {0, 0}
588 int pci_mmc_init(const char *name, struct pci_device_id *mmc_supported);
590 /* Set block count limit because of 16 bit register limit on some hardware*/
591 #ifndef CONFIG_SYS_MMC_MAX_BLK_COUNT
592 #define CONFIG_SYS_MMC_MAX_BLK_COUNT 65535
596 * mmc_get_blk_desc() - Get the block descriptor for an MMC device
599 * @return block device if found, else NULL
601 struct blk_desc *mmc_get_blk_desc(struct mmc *mmc);