tcl: am437x: disable watchdog on reset-end

[openocd] / tcl / target / am437x.cfg

source [find target/icepick.cfg]
source [find mem_helper.tcl]

###############################################################################
##                              AM437x Registers                             ##
###############################################################################
set  PRCM_BASE_ADDR                  0x44df0000
set  REVISION_PRM                    [expr       $PRCM_BASE_ADDR     +  0x0000]
set  PRM_IRQSTATUS_MPU               [expr       $PRCM_BASE_ADDR     +  0x0004]
set  PRM_IRQENABLE_MPU               [expr       $PRCM_BASE_ADDR     +  0x0008]
set  PRM_IRQSTATUS_M3                [expr       $PRCM_BASE_ADDR     +  0x000c]
set  PRM_IRQENABLE_M3                [expr       $PRCM_BASE_ADDR     +  0x0010]
set  PM_MPU_PWRSTCTRL                [expr       $PRCM_BASE_ADDR     +  0x0300]
set  PM_MPU_PWRSTST                  [expr       $PRCM_BASE_ADDR     +  0x0304]
set  RM_MPU_RSTST                    [expr       $PRCM_BASE_ADDR     +  0x0314]
set  RM_MPU_CONTEXT                  [expr       $PRCM_BASE_ADDR     +  0x0324]
set  PM_GFX_PWRSTCTRL                [expr       $PRCM_BASE_ADDR     +  0x0400]
set  PM_GFX_PWRSTST                  [expr       $PRCM_BASE_ADDR     +  0x0404]
set  RM_GFX_RSTCTRL                  [expr       $PRCM_BASE_ADDR     +  0x0410]
set  RM_GFX_RSTST                    [expr       $PRCM_BASE_ADDR     +  0x0414]
set  RM_GFX_CONTEXT                  [expr       $PRCM_BASE_ADDR     +  0x0424]
set  RM_RTC_CONTEXT                  [expr       $PRCM_BASE_ADDR     +  0x0524]
set  RM_WKUP_RSTCTRL                 [expr       $PRCM_BASE_ADDR     +  0x2010]
set  RM_WKUP_RSTST                   [expr       $PRCM_BASE_ADDR     +  0x2014]
set  CM_L3_AON_CLKSTCTRL             [expr       $PRCM_BASE_ADDR     +  0x2800]
set  CM_WKUP_DEBUGSS_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x2820]
set  CM_L3S_TSC_CLKSTCTRL            [expr       $PRCM_BASE_ADDR     +  0x2900]
set  CM_WKUP_ADC_TSC_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x2920]
set  CM_L4_WKUP_AON_CLKSTCTRL        [expr       $PRCM_BASE_ADDR     +  0x2a00]
set  CM_WKUP_L4WKUP_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x2a20]
set  CM_WKUP_WKUP_M3_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x2a28]
set  CM_WKUP_SYNCTIMER_CLKCTRL       [expr       $PRCM_BASE_ADDR     +  0x2a30]
set  CM_WKUP_CLKDIV32K_CLKCTRL       [expr       $PRCM_BASE_ADDR     +  0x2a38]
set  CM_WKUP_USBPHY0_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x2a40]
set  CM_WKUP_USBPHY1_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x2a48]
set  CM_WKUP_CLKSTCTRL               [expr       $PRCM_BASE_ADDR     +  0x2b00]
set  CM_WKUP_TIMER0_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x2b20]
set  CM_WKUP_TIMER1_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x2b28]
set  CM_WKUP_WDT0_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x2b30]
set  CM_WKUP_WDT1_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x2b38]
set  CM_WKUP_I2C0_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x2b40]
set  CM_WKUP_UART0_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x2b48]
set  CM_WKUP_SMARTREFLEX0_CLKCTRL    [expr       $PRCM_BASE_ADDR     +  0x2b50]
set  CM_WKUP_SMARTREFLEX1_CLKCTRL    [expr       $PRCM_BASE_ADDR     +  0x2b58]
set  CM_WKUP_CONTROL_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x2b60]
set  CM_WKUP_GPIO0_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x2b68]
set  CM_CLKMODE_DPLL_CORE            [expr       $PRCM_BASE_ADDR     +  0x2d20]
set  CM_IDLEST_DPLL_CORE             [expr       $PRCM_BASE_ADDR     +  0x2d24]
set  CM_CLKSEL_DPLL_CORE             [expr       $PRCM_BASE_ADDR     +  0x2d2c]
set  CM_DIV_M4_DPLL_CORE             [expr       $PRCM_BASE_ADDR     +  0x2d38]
set  CM_DIV_M5_DPLL_CORE             [expr       $PRCM_BASE_ADDR     +  0x2d3c]
set  CM_DIV_M6_DPLL_CORE             [expr       $PRCM_BASE_ADDR     +  0x2d40]
set  CM_SSC_DELTAMSTEP_DPLL_CORE     [expr       $PRCM_BASE_ADDR     +  0x2d48]
set  CM_SSC_MODFREQDIV_DPLL_CORE     [expr       $PRCM_BASE_ADDR     +  0x2d4c]
set  CM_CLKMODE_DPLL_MPU             [expr       $PRCM_BASE_ADDR     +  0x2d60]
set  CM_IDLEST_DPLL_MPU              [expr       $PRCM_BASE_ADDR     +  0x2d64]
set  CM_CLKSEL_DPLL_MPU              [expr       $PRCM_BASE_ADDR     +  0x2d6c]
set  CM_DIV_M2_DPLL_MPU              [expr       $PRCM_BASE_ADDR     +  0x2d70]
set  CM_SSC_DELTAMSTEP_DPLL_MPU      [expr       $PRCM_BASE_ADDR     +  0x2d88]
set  CM_SSC_MODFREQDIV_DPLL_MPU      [expr       $PRCM_BASE_ADDR     +  0x2d8c]
set  CM_CLKMODE_DPLL_DDR             [expr       $PRCM_BASE_ADDR     +  0x2da0]
set  CM_IDLEST_DPLL_DDR              [expr       $PRCM_BASE_ADDR     +  0x2da4]
set  CM_CLKSEL_DPLL_DDR              [expr       $PRCM_BASE_ADDR     +  0x2dac]
set  CM_DIV_M2_DPLL_DDR              [expr       $PRCM_BASE_ADDR     +  0x2db0]
set  CM_DIV_M4_DPLL_DDR              [expr       $PRCM_BASE_ADDR     +  0x2db8]
set  CM_SSC_DELTAMSTEP_DPLL_DDR      [expr       $PRCM_BASE_ADDR     +  0x2dc8]
set  CM_SSC_MODFREQDIV_DPLL_DDR      [expr       $PRCM_BASE_ADDR     +  0x2dcc]
set  CM_CLKMODE_DPLL_PER             [expr       $PRCM_BASE_ADDR     +  0x2de0]
set  CM_IDLEST_DPLL_PER              [expr       $PRCM_BASE_ADDR     +  0x2de4]
set  CM_CLKSEL_DPLL_PER              [expr       $PRCM_BASE_ADDR     +  0x2dec]
set  CM_DIV_M2_DPLL_PER              [expr       $PRCM_BASE_ADDR     +  0x2df0]
set  CM_CLKSEL2_DPLL_PER             [expr       $PRCM_BASE_ADDR     +  0x2e04]
set  CM_SSC_DELTAMSTEP_DPLL_PER      [expr       $PRCM_BASE_ADDR     +  0x2e08]
set  CM_SSC_MODFREQDIV_DPLL_PER      [expr       $PRCM_BASE_ADDR     +  0x2e0c]
set  CM_CLKDCOLDO_DPLL_PER           [expr       $PRCM_BASE_ADDR     +  0x2e14]
set  CM_CLKMODE_DPLL_DISP            [expr       $PRCM_BASE_ADDR     +  0x2e20]
set  CM_IDLEST_DPLL_DISP             [expr       $PRCM_BASE_ADDR     +  0x2e24]
set  CM_CLKSEL_DPLL_DISP             [expr       $PRCM_BASE_ADDR     +  0x2e2c]
set  CM_DIV_M2_DPLL_DISP             [expr       $PRCM_BASE_ADDR     +  0x2e30]
set  CM_SSC_DELTAMSTEP_DPLL_DISP     [expr       $PRCM_BASE_ADDR     +  0x2e48]
set  CM_SSC_MODFREQDIV_DPLL_DISP     [expr       $PRCM_BASE_ADDR     +  0x2e4c]
set  CM_CLKMODE_DPLL_EXTDEV          [expr       $PRCM_BASE_ADDR     +  0x2e60]
set  CM_IDLEST_DPLL_EXTDEV           [expr       $PRCM_BASE_ADDR     +  0x2e64]
set  CM_CLKSEL_DPLL_EXTDEV           [expr       $PRCM_BASE_ADDR     +  0x2e6c]
set  CM_DIV_M2_DPLL_EXTDEV           [expr       $PRCM_BASE_ADDR     +  0x2e70]
set  CM_CLKSEL2_DPLL_EXTDEV          [expr       $PRCM_BASE_ADDR     +  0x2e84]
set  CM_SSC_DELTAMSTEP_DPLL_EXTDEV   [expr       $PRCM_BASE_ADDR     +  0x2e88]
set  CM_SSC_MODFREQDIV_DPLL_EXTDEV   [expr       $PRCM_BASE_ADDR     +  0x2e8c]
set  CM_SHADOW_FREQ_CONFIG1          [expr       $PRCM_BASE_ADDR     +  0x2fa0]
set  CM_SHADOW_FREQ_CONFIG2          [expr       $PRCM_BASE_ADDR     +  0x2fa4]
set  CM_CLKOUT1_CTRL                 [expr       $PRCM_BASE_ADDR     +  0x4100]
set  CM_DLL_CTRL                     [expr       $PRCM_BASE_ADDR     +  0x4104]
set  CM_CLKOUT2_CTRL                 [expr       $PRCM_BASE_ADDR     +  0x4108]
set  CLKSEL_TIMER1MS_CLK             [expr       $PRCM_BASE_ADDR     +  0x4200]
set  CLKSEL_TIMER2_CLK               [expr       $PRCM_BASE_ADDR     +  0x4204]
set  CLKSEL_TIMER3_CLK               [expr       $PRCM_BASE_ADDR     +  0x4208]
set  CLKSEL_TIMER4_CLK               [expr       $PRCM_BASE_ADDR     +  0x420c]
set  CLKSEL_TIMER5_CLK               [expr       $PRCM_BASE_ADDR     +  0x4210]
set  CLKSEL_TIMER6_CLK               [expr       $PRCM_BASE_ADDR     +  0x4214]
set  CLKSEL_TIMER7_CLK               [expr       $PRCM_BASE_ADDR     +  0x4218]
set  CLKSEL_TIMER8_CLK               [expr       $PRCM_BASE_ADDR     +  0x421c]
set  CLKSEL_TIMER9_CLK               [expr       $PRCM_BASE_ADDR     +  0x4220]
set  CLKSEL_TIMER10_CLK              [expr       $PRCM_BASE_ADDR     +  0x4224]
set  CLKSEL_TIMER11_CLK              [expr       $PRCM_BASE_ADDR     +  0x4228]
set  CLKSEL_WDT1_CLK                 [expr       $PRCM_BASE_ADDR     +  0x422c]
set  CLKSEL_SYNCTIMER_CLK            [expr       $PRCM_BASE_ADDR     +  0x4230]
set  CLKSEL_MAC_CLK                  [expr       $PRCM_BASE_ADDR     +  0x4234]
set  CLKSEL_CPTS_RFT_CLK             [expr       $PRCM_BASE_ADDR     +  0x4238]
set  CLKSEL_GFX_FCLK                 [expr       $PRCM_BASE_ADDR     +  0x423c]
set  CLKSEL_GPIO0_DBCLK              [expr       $PRCM_BASE_ADDR     +  0x4240]
set  CLKSEL_LCDC_PIXEL_CLK           [expr       $PRCM_BASE_ADDR     +  0x4244]
set  CLKSEL_ICSS_OCP_CLK             [expr       $PRCM_BASE_ADDR     +  0x4248]
set  CLKSEL_DLL_AGING_CLK            [expr       $PRCM_BASE_ADDR     +  0x4250]
set  CLKSEL_USBPHY32KHZ_GCLK         [expr       $PRCM_BASE_ADDR     +  0x4260]
set  CM_MPU_CLKSTCTRL                [expr       $PRCM_BASE_ADDR     +  0x8300]
set  CM_MPU_MPU_CLKCTRL              [expr       $PRCM_BASE_ADDR     +  0x8320]
set  CM_GFX_L3_CLKSTCTRL             [expr       $PRCM_BASE_ADDR     +  0x8400]
set  CM_GFX_GFX_CLKCTRL              [expr       $PRCM_BASE_ADDR     +  0x8420]
set  CM_RTC_CLKSTCTRL                [expr       $PRCM_BASE_ADDR     +  0x8500]
set  CM_RTC_RTC_CLKCTRL              [expr       $PRCM_BASE_ADDR     +  0x8520]
set  CM_PER_L3_CLKSTCTRL             [expr       $PRCM_BASE_ADDR     +  0x8800]
set  CM_PER_L3_CLKCTRL               [expr       $PRCM_BASE_ADDR     +  0x8820]
set  CM_PER_AES0_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8828]
set  CM_PER_DES_CLKCTRL              [expr       $PRCM_BASE_ADDR     +  0x8830]
set  CM_PER_CRYPTODMA_CLKCTRL        [expr       $PRCM_BASE_ADDR     +  0x8838]
set  CM_PER_L3_INSTR_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x8840]
set  CM_PER_MSTR_EXPS_CLKCTRL        [expr       $PRCM_BASE_ADDR     +  0x8848]
set  CM_PER_OCMCRAM_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x8850]
set  CM_PER_SHA0_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8858]
set  CM_PER_SLV_EXPS_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x8860]
set  CM_PER_VPFE0_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8868]
set  CM_PER_VPFE1_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8870]
set  CM_PER_TPCC_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8878]
set  CM_PER_TPTC0_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8880]
set  CM_PER_TPTC1_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8888]
set  CM_PER_TPTC2_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8890]
set  CM_PER_DLL_AGING_CLKCTRL        [expr       $PRCM_BASE_ADDR     +  0x8898]
set  CM_PER_L4HS_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x88a0]
set  CM_PER_L4FW_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x88a8]
set  CM_PER_L3S_CLKSTCTRL            [expr       $PRCM_BASE_ADDR     +  0x8a00]
set  CM_PER_GPMC_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8a20]
set  CM_PER_IEEE5000_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x8a28]
set  CM_PER_MCASP0_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8a38]
set  CM_PER_MCASP1_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8a40]
set  CM_PER_MMC2_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8a48]
set  CM_PER_QSPI_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8a58]
set  CM_PER_USB_OTG_SS0_CLKCTRL      [expr       $PRCM_BASE_ADDR     +  0x8a60]
set  CM_PER_USB_OTG_SS1_CLKCTRL      [expr       $PRCM_BASE_ADDR     +  0x8a68]
set  CM_PER_ICSS_CLKSTCTRL           [expr       $PRCM_BASE_ADDR     +  0x8b00]
set  CM_PER_ICSS_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8b20]
set  CM_PER_L4LS_CLKSTCTRL           [expr       $PRCM_BASE_ADDR     +  0x8c00]
set  CM_PER_L4LS_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8c20]
set  CM_PER_DCAN0_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8c28]
set  CM_PER_DCAN1_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8c30]
set  CM_PER_EPWMSS0_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x8c38]
set  CM_PER_EPWMSS1_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x8c40]
set  CM_PER_EPWMSS2_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x8c48]
set  CM_PER_EPWMSS3_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x8c50]
set  CM_PER_EPWMSS4_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x8c58]
set  CM_PER_EPWMSS5_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x8c60]
set  CM_PER_ELM_CLKCTRL              [expr       $PRCM_BASE_ADDR     +  0x8c68]
set  CM_PER_GPIO1_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8c78]
set  CM_PER_GPIO2_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8c80]
set  CM_PER_GPIO3_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8c88]
set  CM_PER_GPIO4_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8c90]
set  CM_PER_GPIO5_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8c98]
set  CM_PER_HDQ1W_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8ca0]
set  CM_PER_I2C1_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8ca8]
set  CM_PER_I2C2_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8cb0]
set  CM_PER_MAILBOX0_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x8cb8]
set  CM_PER_MMC0_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8cc0]
set  CM_PER_MMC1_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8cc8]
set  CM_PER_PKA_CLKCTRL              [expr       $PRCM_BASE_ADDR     +  0x8cd0]
set  CM_PER_RNG_CLKCTRL              [expr       $PRCM_BASE_ADDR     +  0x8ce0]
set  CM_PER_SPARE0_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8ce8]
set  CM_PER_SPARE1_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8cf0]
set  CM_PER_SPI0_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8d00]
set  CM_PER_SPI1_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8d08]
set  CM_PER_SPI2_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8d10]
set  CM_PER_SPI3_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8d18]
set  CM_PER_SPI4_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8d20]
set  CM_PER_SPINLOCK_CLKCTRL         [expr       $PRCM_BASE_ADDR     +  0x8d28]
set  CM_PER_TIMER2_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8d30]
set  CM_PER_TIMER3_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8d38]
set  CM_PER_TIMER4_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8d40]
set  CM_PER_TIMER5_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8d48]
set  CM_PER_TIMER6_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8d50]
set  CM_PER_TIMER7_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8d58]
set  CM_PER_TIMER8_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8d60]
set  CM_PER_TIMER9_CLKCTRL           [expr       $PRCM_BASE_ADDR     +  0x8d68]
set  CM_PER_TIMER10_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x8d70]
set  CM_PER_TIMER11_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x8d78]
set  CM_PER_UART1_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8d80]
set  CM_PER_UART2_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8d88]
set  CM_PER_UART3_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8d90]
set  CM_PER_UART4_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8d98]
set  CM_PER_UART5_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x8da0]
set  CM_PER_USBPHYOCP2SCP0_CLKCTRL   [expr       $PRCM_BASE_ADDR     +  0x8db8]
set  CM_PER_USBPHYOCP2SCP1_CLKCTRL   [expr       $PRCM_BASE_ADDR     +  0x8dc0]
set  CM_PER_EMIF_CLKSTCTRL           [expr       $PRCM_BASE_ADDR     +  0x8f00]
set  CM_PER_EMIF_CLKCTRL             [expr       $PRCM_BASE_ADDR     +  0x8f20]
set  CM_PER_DLL_CLKCTRL              [expr       $PRCM_BASE_ADDR     +  0x8f28]
set  CM_PER_EMIF_FW_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x8f30]
set  CM_PER_OTFA_EMIF_CLKCTRL        [expr       $PRCM_BASE_ADDR     +  0x8f38]
set  CM_PER_DSS_CLKSTCTRL            [expr       $PRCM_BASE_ADDR     +  0x9200]
set  CM_PER_DSS_CLKCTRL              [expr       $PRCM_BASE_ADDR     +  0x9220]
set  CM_PER_CPSW_CLKSTCTRL           [expr       $PRCM_BASE_ADDR     +  0x9300]
set  CM_PER_CPGMAC0_CLKCTRL          [expr       $PRCM_BASE_ADDR     +  0x9320]
set  CM_PER_OCPWP_L3_CLKSTCTRL       [expr       $PRCM_BASE_ADDR     +  0x9400]
set  CM_PER_OCPWP_CLKCTRL            [expr       $PRCM_BASE_ADDR     +  0x9420]

set  CONTROL_BASE_ADDR               0x44e10000
set  CONTROL_STATUS                  [expr       $CONTROL_BASE_ADDR  +  0x0040]
set  DEVICE_ID                       [expr       $CONTROL_BASE_ADDR  +  0x0600]
set  DEV_FEATURE                     [expr       $CONTROL_BASE_ADDR  +  0x0604]
set  DEV_ATTRIBUTE                   [expr       $CONTROL_BASE_ADDR  +  0x0610]
set  MAC_ID0_LO                      [expr       $CONTROL_BASE_ADDR  +  0x0630]
set  MAC_ID0_HI                      [expr       $CONTROL_BASE_ADDR  +  0x0634]
set  MAC_ID1_LO                      [expr       $CONTROL_BASE_ADDR  +  0x0638]
set  MAC_ID1_HI                      [expr       $CONTROL_BASE_ADDR  +  0x063c]
set  USB_VID_PID                     [expr       $CONTROL_BASE_ADDR  +  0x07f4]
set  CONTROL_CONF_ECAP0_IN_PWM0_OUT  [expr       $CONTROL_BASE_ADDR  +  0x0964]
set  CONTROL_CONF_SPI4_CS0           [expr       $CONTROL_BASE_ADDR  +  0x0a5c]
set  CONTROL_CONF_SPI2_SCLK          [expr       $CONTROL_BASE_ADDR  +  0x0a60]
set  CONTROL_CONF_SPI2_D0            [expr       $CONTROL_BASE_ADDR  +  0x0a64]
set  CONTROL_CONF_XDMA_EVENT_INTR0   [expr       $CONTROL_BASE_ADDR  +  0x0a70]
set  CONTROL_CONF_XDMA_EVENT_INTR1   [expr       $CONTROL_BASE_ADDR  +  0x0a74]
set  CONTROL_CONF_GPMC_A0            [expr       $CONTROL_BASE_ADDR  +  0x0840]
set  DDR_IO_CTRL                     [expr       $CONTROL_BASE_ADDR  +  0x0e04]
set  VTP_CTRL_REG                    [expr       $CONTROL_BASE_ADDR  +  0x0e0c]
set  VREF_CTRL                       [expr       $CONTROL_BASE_ADDR  +  0x0e14]
set  DDR_CKE_CTRL                    [expr       $CONTROL_BASE_ADDR  +  0x131c]
set  DDR_ADDRCTRL_IOCTRL             [expr       $CONTROL_BASE_ADDR  +  0x1404]
set  DDR_ADDRCTRL_WD0_IOCTRL         [expr       $CONTROL_BASE_ADDR  +  0x1408]
set  DDR_ADDRCTRL_WD1_IOCTRL         [expr       $CONTROL_BASE_ADDR  +  0x140c]
set  DDR_DATA0_IOCTRL                [expr       $CONTROL_BASE_ADDR  +  0x1440]
set  DDR_DATA1_IOCTRL                [expr       $CONTROL_BASE_ADDR  +  0x1444]
set  DDR_DATA2_IOCTRL                [expr       $CONTROL_BASE_ADDR  +  0x1448]
set  DDR_DATA3_IOCTRL                [expr       $CONTROL_BASE_ADDR  +  0x144c]
set  EMIF_SDRAM_CONFIG_EXT           [expr       $CONTROL_BASE_ADDR  +  0x1460]
set  EMIF_SDRAM_STATUS_EXT           [expr       $CONTROL_BASE_ADDR  +  0x1464]

set  GPIO0_BASE_ADDR                 0x44e07000
set  GPIO0_SYSCONFIG                 [expr       $GPIO0_BASE_ADDR    +  0x0010]
set  GPIO0_SYSSTATUS                 [expr       $GPIO0_BASE_ADDR    +  0x0114]
set  GPIO0_CTRL                      [expr       $GPIO0_BASE_ADDR    +  0x0130]
set  GPIO0_OE                        [expr       $GPIO0_BASE_ADDR    +  0x0134]
set  GPIO0_CLEARDATAOUT              [expr       $GPIO0_BASE_ADDR    +  0x0190]
set  GPIO0_SETDATAOUT                [expr       $GPIO0_BASE_ADDR    +  0x0194]

set  GPIO5_BASE_ADDR                 0x48322000
set  GPIO5_SYSCONFIG                 [expr       $GPIO5_BASE_ADDR    +  0x0010]
set  GPIO5_SYSSTATUS                 [expr       $GPIO5_BASE_ADDR    +  0x0114]
set  GPIO5_CTRL                      [expr       $GPIO5_BASE_ADDR    +  0x0130]
set  GPIO5_OE                        [expr       $GPIO5_BASE_ADDR    +  0x0134]
set  GPIO5_CLEARDATAOUT              [expr       $GPIO5_BASE_ADDR    +  0x0190]
set  GPIO5_SETDATAOUT                [expr       $GPIO5_BASE_ADDR    +  0x0194]

set  GPIO1_BASE_ADDR                 0x4804c000
set  GPIO1_SYSCONFIG                 [expr       $GPIO1_BASE_ADDR    +  0x0010]
set  GPIO1_SYSSTATUS                 [expr       $GPIO1_BASE_ADDR    +  0x0114]
set  GPIO1_CTRL                      [expr       $GPIO1_BASE_ADDR    +  0x0130]
set  GPIO1_OE                        [expr       $GPIO1_BASE_ADDR    +  0x0134]
set  GPIO1_CLEARDATAOUT              [expr       $GPIO1_BASE_ADDR    +  0x0190]
set  GPIO1_SETDATAOUT                [expr       $GPIO1_BASE_ADDR    +  0x0194]

set  EMIF_BASE_ADDR                  0x4c000000
set  EMIF_STATUS                     [expr       $EMIF_BASE_ADDR     +  0x0004]
set  EMIF_SDRAM_CONFIG               [expr       $EMIF_BASE_ADDR     +  0x0008]
set  EMIF_SDRAM_CONFIG_2             [expr       $EMIF_BASE_ADDR     +  0x000c]
set  EMIF_SDRAM_REF_CTRL             [expr       $EMIF_BASE_ADDR     +  0x0010]
set  EMIF_SDRAM_REF_CTRL_SHDW        [expr       $EMIF_BASE_ADDR     +  0x0014]
set  EMIF_SDRAM_TIM_1                [expr       $EMIF_BASE_ADDR     +  0x0018]
set  EMIF_SDRAM_TIM_1_SHDW           [expr       $EMIF_BASE_ADDR     +  0x001c]
set  EMIF_SDRAM_TIM_2                [expr       $EMIF_BASE_ADDR     +  0x0020]
set  EMIF_SDRAM_TIM_2_SHDW           [expr       $EMIF_BASE_ADDR     +  0x0024]
set  EMIF_SDRAM_TIM_3                [expr       $EMIF_BASE_ADDR     +  0x0028]
set  EMIF_SDRAM_TIM_3_SHDW           [expr       $EMIF_BASE_ADDR     +  0x002c]
set  EMIF_LPDDR2_NVM_TIM             [expr       $EMIF_BASE_ADDR     +  0x0030]
set  EMIF_LPDDR2_NVM_TIM_SHDW        [expr       $EMIF_BASE_ADDR     +  0x0034]
set  EMIF_PWR_MGMT_CTRL              [expr       $EMIF_BASE_ADDR     +  0x0038]
set  EMIF_PWR_MGMT_CTRL_SHDW         [expr       $EMIF_BASE_ADDR     +  0x003c]
set  EMIF_LPDDR2_MODE_REG_DATA       [expr       $EMIF_BASE_ADDR     +  0x0040]
set  EMIF_LPDDR2_MODE_REG_CFG        [expr       $EMIF_BASE_ADDR     +  0x0050]
set  EMIF_OCP_CONFIG                 [expr       $EMIF_BASE_ADDR     +  0x0054]
set  EMIF_OCP_CFG_VAL_1              [expr       $EMIF_BASE_ADDR     +  0x0058]
set  EMIF_OCP_CFG_VAL_2              [expr       $EMIF_BASE_ADDR     +  0x005c]
set  EMIF_IODFT_TLGC                 [expr       $EMIF_BASE_ADDR     +  0x0060]
set  EMIF_IODFT_CTRL_MISR_RSLT       [expr       $EMIF_BASE_ADDR     +  0x0064]
set  EMIF_IODFT_ADDR_MISR_RSLT       [expr       $EMIF_BASE_ADDR     +  0x0068]
set  EMIF_IODFT_DATA_MISR_RSLT_1     [expr       $EMIF_BASE_ADDR     +  0x006c]
set  EMIF_IODFT_DATA_MISR_RSLT_2     [expr       $EMIF_BASE_ADDR     +  0x0070]
set  EMIF_IODFT_DATA_MISR_RSLT_3     [expr       $EMIF_BASE_ADDR     +  0x0074]
set  EMIF_PERF_CNT_1                 [expr       $EMIF_BASE_ADDR     +  0x0080]
set  EMIF_PERF_CNT_2                 [expr       $EMIF_BASE_ADDR     +  0x0084]
set  EMIF_PERF_CNT_CFG               [expr       $EMIF_BASE_ADDR     +  0x0088]
set  EMIF_PERF_CNT_SEL               [expr       $EMIF_BASE_ADDR     +  0x008c]
set  EMIF_PERF_CNT_TIM               [expr       $EMIF_BASE_ADDR     +  0x0090]
set  EMIF_MISC_REG                   [expr       $EMIF_BASE_ADDR     +  0x0094]
set  EMIF_DLL_CALIB_CTRL             [expr       $EMIF_BASE_ADDR     +  0x0098]
set  EMIF_DLL_CALIB_CTRL_SHDW        [expr       $EMIF_BASE_ADDR     +  0x009c]
set  EMIF_IRQ_EOI                    [expr       $EMIF_BASE_ADDR     +  0x00a0]
set  EMIF_IRQSTATUS_RAW_SYS          [expr       $EMIF_BASE_ADDR     +  0x00a4]
set  EMIF_IRQSTATUS_SYS              [expr       $EMIF_BASE_ADDR     +  0x00ac]
set  EMIF_IRQENABLE_SET_SYS          [expr       $EMIF_BASE_ADDR     +  0x00b4]
set  EMIF_IRQENABLE_CLR_SYS          [expr       $EMIF_BASE_ADDR     +  0x00bc]
set  EMIF_ZQ_CONFIG                  [expr       $EMIF_BASE_ADDR     +  0x00c8]
set  EMIF_TEMP_ALERT_CONFIG          [expr       $EMIF_BASE_ADDR     +  0x00cc]
set  EMIF_OCP_ERR_LOG                [expr       $EMIF_BASE_ADDR     +  0x00d0]
set  EMIF_RDWR_LVL_RMP_WIN           [expr       $EMIF_BASE_ADDR     +  0x00d4]
set  EMIF_RDWR_LVL_RMP_CTRL          [expr       $EMIF_BASE_ADDR     +  0x00d8]
set  EMIF_RDWR_LVL_CTRL              [expr       $EMIF_BASE_ADDR     +  0x00dc]
set  EMIF_DDR_PHY_CTRL_1             [expr       $EMIF_BASE_ADDR     +  0x00e4]
set  EMIF_DDR_PHY_CTRL_1_SHDW        [expr       $EMIF_BASE_ADDR     +  0x00e8]
set  EMIF_DDR_PHY_CTRL_2             [expr       $EMIF_BASE_ADDR     +  0x00ec]
set  EMIF_PRI_COS_MAP                [expr       $EMIF_BASE_ADDR     +  0x0100]
set  EMIF_CONNID_COS_1_MAP           [expr       $EMIF_BASE_ADDR     +  0x0104]
set  EMIF_CONNID_COS_2_MAP           [expr       $EMIF_BASE_ADDR     +  0x0108]
set  ECC_CTRL                        [expr       $EMIF_BASE_ADDR     +  0x0110]
set  ECC_ADDR_RNG_1                  [expr       $EMIF_BASE_ADDR     +  0x0114]
set  ECC_ADDR_RNG_2                  [expr       $EMIF_BASE_ADDR     +  0x0118]
set  EMIF_RD_WR_EXEC_THRSH           [expr       $EMIF_BASE_ADDR     +  0x0120]
set  COS_CONFIG                      [expr       $EMIF_BASE_ADDR     +  0x0124]

set  PHY_STATUS_1                    [expr       $EMIF_BASE_ADDR     +  0x0144]
set  PHY_STATUS_2                    [expr       $EMIF_BASE_ADDR     +  0x0148]
set  PHY_STATUS_3                    [expr       $EMIF_BASE_ADDR     +  0x014c]
set  PHY_STATUS_4                    [expr       $EMIF_BASE_ADDR     +  0x0150]
set  PHY_STATUS_5                    [expr       $EMIF_BASE_ADDR     +  0x0154]
set  PHY_STATUS_6                    [expr       $EMIF_BASE_ADDR     +  0x0158]
set  PHY_STATUS_7                    [expr       $EMIF_BASE_ADDR     +  0x015c]
set  PHY_STATUS_8                    [expr       $EMIF_BASE_ADDR     +  0x0160]
set  PHY_STATUS_9                    [expr       $EMIF_BASE_ADDR     +  0x0164]
set  PHY_STATUS_10                   [expr       $EMIF_BASE_ADDR     +  0x0168]
set  PHY_STATUS_11                   [expr       $EMIF_BASE_ADDR     +  0x016c]
set  PHY_STATUS_12                   [expr       $EMIF_BASE_ADDR     +  0x0170]
set  PHY_STATUS_13                   [expr       $EMIF_BASE_ADDR     +  0x0174]
set  PHY_STATUS_14                   [expr       $EMIF_BASE_ADDR     +  0x0178]
set  PHY_STATUS_15                   [expr       $EMIF_BASE_ADDR     +  0x017c]
set  PHY_STATUS_16                   [expr       $EMIF_BASE_ADDR     +  0x0180]
set  PHY_STATUS_17                   [expr       $EMIF_BASE_ADDR     +  0x0184]
set  PHY_STATUS_18                   [expr       $EMIF_BASE_ADDR     +  0x0188]
set  PHY_STATUS_19                   [expr       $EMIF_BASE_ADDR     +  0x018c]
set  PHY_STATUS_20                   [expr       $EMIF_BASE_ADDR     +  0x0190]
set  PHY_STATUS_21                   [expr       $EMIF_BASE_ADDR     +  0x0194]
set  PHY_STATUS_22                   [expr       $EMIF_BASE_ADDR     +  0x0198]
set  PHY_STATUS_23                   [expr       $EMIF_BASE_ADDR     +  0x019c]
set  PHY_STATUS_24                   [expr       $EMIF_BASE_ADDR     +  0x01a0]
set  PHY_STATUS_25                   [expr       $EMIF_BASE_ADDR     +  0x01a4]
set  PHY_STATUS_26                   [expr       $EMIF_BASE_ADDR     +  0x01a8]
set  PHY_STATUS_27                   [expr       $EMIF_BASE_ADDR     +  0x01ac]
set  PHY_STATUS_28                   [expr       $EMIF_BASE_ADDR     +  0x01b0]

set  EXT_PHY_CTRL_1                  [expr       $EMIF_BASE_ADDR     +  0x0200]
set  EXT_PHY_CTRL_1_SHDW             [expr       $EMIF_BASE_ADDR     +  0x0204]
set  EXT_PHY_CTRL_2                  [expr       $EMIF_BASE_ADDR     +  0x0208]
set  EXT_PHY_CTRL_2_SHDW             [expr       $EMIF_BASE_ADDR     +  0x020c]
set  EXT_PHY_CTRL_3                  [expr       $EMIF_BASE_ADDR     +  0x0210]
set  EXT_PHY_CTRL_3_SHDW             [expr       $EMIF_BASE_ADDR     +  0x0214]
set  EXT_PHY_CTRL_4                  [expr       $EMIF_BASE_ADDR     +  0x0218]
set  EXT_PHY_CTRL_4_SHDW             [expr       $EMIF_BASE_ADDR     +  0x021c]
set  EXT_PHY_CTRL_5                  [expr       $EMIF_BASE_ADDR     +  0x0220]
set  EXT_PHY_CTRL_5_SHDW             [expr       $EMIF_BASE_ADDR     +  0x0224]
set  EXT_PHY_CTRL_6                  [expr       $EMIF_BASE_ADDR     +  0x0228]
set  EXT_PHY_CTRL_6_SHDW             [expr       $EMIF_BASE_ADDR     +  0x022c]
set  EXT_PHY_CTRL_7                  [expr       $EMIF_BASE_ADDR     +  0x0230]
set  EXT_PHY_CTRL_7_SHDW             [expr       $EMIF_BASE_ADDR     +  0x0234]
set  EXT_PHY_CTRL_8                  [expr       $EMIF_BASE_ADDR     +  0x0238]
set  EXT_PHY_CTRL_8_SHDW             [expr       $EMIF_BASE_ADDR     +  0x023c]
set  EXT_PHY_CTRL_9                  [expr       $EMIF_BASE_ADDR     +  0x0240]
set  EXT_PHY_CTRL_9_SHDW             [expr       $EMIF_BASE_ADDR     +  0x0244]
set  EXT_PHY_CTRL_10                 [expr       $EMIF_BASE_ADDR     +  0x0248]
set  EXT_PHY_CTRL_10_SHDW            [expr       $EMIF_BASE_ADDR     +  0x024c]
set  EXT_PHY_CTRL_11                 [expr       $EMIF_BASE_ADDR     +  0x0250]
set  EXT_PHY_CTRL_11_SHDW            [expr       $EMIF_BASE_ADDR     +  0x0254]
set  EXT_PHY_CTRL_12                 [expr       $EMIF_BASE_ADDR     +  0x0258]
set  EXT_PHY_CTRL_12_SHDW            [expr       $EMIF_BASE_ADDR     +  0x025c]
set  EXT_PHY_CTRL_13                 [expr       $EMIF_BASE_ADDR     +  0x0260]
set  EXT_PHY_CTRL_13_SHDW            [expr       $EMIF_BASE_ADDR     +  0x0264]
set  EXT_PHY_CTRL_14                 [expr       $EMIF_BASE_ADDR     +  0x0268]
set  EXT_PHY_CTRL_14_SHDW            [expr       $EMIF_BASE_ADDR     +  0x026c]
set  EXT_PHY_CTRL_15                 [expr       $EMIF_BASE_ADDR     +  0x0270]
set  EXT_PHY_CTRL_15_SHDW            [expr       $EMIF_BASE_ADDR     +  0x0274]
set  EXT_PHY_CTRL_16                 [expr       $EMIF_BASE_ADDR     +  0x0278]
set  EXT_PHY_CTRL_16_SHDW            [expr       $EMIF_BASE_ADDR     +  0x027c]
set  EXT_PHY_CTRL_17                 [expr       $EMIF_BASE_ADDR     +  0x0280]
set  EXT_PHY_CTRL_17_SHDW            [expr       $EMIF_BASE_ADDR     +  0x0284]
set  EXT_PHY_CTRL_18                 [expr       $EMIF_BASE_ADDR     +  0x0288]
set  EXT_PHY_CTRL_18_SHDW            [expr       $EMIF_BASE_ADDR     +  0x028c]
set  EXT_PHY_CTRL_19                 [expr       $EMIF_BASE_ADDR     +  0x0290]
set  EXT_PHY_CTRL_19_SHDW            [expr       $EMIF_BASE_ADDR     +  0x0294]
set  EXT_PHY_CTRL_20                 [expr       $EMIF_BASE_ADDR     +  0x0298]
set  EXT_PHY_CTRL_20_SHDW            [expr       $EMIF_BASE_ADDR     +  0x029c]
set  EXT_PHY_CTRL_21                 [expr       $EMIF_BASE_ADDR     +  0x02a0]
set  EXT_PHY_CTRL_21_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02a4]
set  EXT_PHY_CTRL_22                 [expr       $EMIF_BASE_ADDR     +  0x02a8]
set  EXT_PHY_CTRL_22_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02ac]
set  EXT_PHY_CTRL_23                 [expr       $EMIF_BASE_ADDR     +  0x02b0]
set  EXT_PHY_CTRL_23_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02b4]
set  EXT_PHY_CTRL_24                 [expr       $EMIF_BASE_ADDR     +  0x02b8]
set  EXT_PHY_CTRL_24_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02bc]
set  EXT_PHY_CTRL_25                 [expr       $EMIF_BASE_ADDR     +  0x02c0]
set  EXT_PHY_CTRL_25_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02c4]
set  EXT_PHY_CTRL_26                 [expr       $EMIF_BASE_ADDR     +  0x02c8]
set  EXT_PHY_CTRL_26_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02cc]
set  EXT_PHY_CTRL_27                 [expr       $EMIF_BASE_ADDR     +  0x02d0]
set  EXT_PHY_CTRL_27_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02d4]
set  EXT_PHY_CTRL_28                 [expr       $EMIF_BASE_ADDR     +  0x02d8]
set  EXT_PHY_CTRL_28_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02dc]
set  EXT_PHY_CTRL_29                 [expr       $EMIF_BASE_ADDR     +  0x02e0]
set  EXT_PHY_CTRL_29_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02e4]
set  EXT_PHY_CTRL_30                 [expr       $EMIF_BASE_ADDR     +  0x02e8]
set  EXT_PHY_CTRL_30_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02ec]
set  EXT_PHY_CTRL_31                 [expr       $EMIF_BASE_ADDR     +  0x02f0]
set  EXT_PHY_CTRL_31_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02f4]
set  EXT_PHY_CTRL_32                 [expr       $EMIF_BASE_ADDR     +  0x02f8]
set  EXT_PHY_CTRL_32_SHDW            [expr       $EMIF_BASE_ADDR     +  0x02fc]
set  EXT_PHY_CTRL_33                 [expr       $EMIF_BASE_ADDR     +  0x0300]
set  EXT_PHY_CTRL_33_SHDW            [expr       $EMIF_BASE_ADDR     +  0x0304]
set  EXT_PHY_CTRL_34                 [expr       $EMIF_BASE_ADDR     +  0x0308]
set  EXT_PHY_CTRL_34_SHDW            [expr       $EMIF_BASE_ADDR     +  0x030c]
set  EXT_PHY_CTRL_35                 [expr       $EMIF_BASE_ADDR     +  0x0310]
set  EXT_PHY_CTRL_35_SHDW            [expr       $EMIF_BASE_ADDR     +  0x0314]
set  EXT_PHY_CTRL_36                 [expr       $EMIF_BASE_ADDR     +  0x0318]
set  EXT_PHY_CTRL_36_SHDW            [expr       $EMIF_BASE_ADDR     +  0x031c]

set  WDT1_BASE_ADDR                  0x44e35000
set  WDT1_W_PEND_WSPR                [expr       $WDT1_BASE_ADDR     +  0x0034]
set  WDT1_WSPR                       [expr       $WDT1_BASE_ADDR     +  0x0048]

set  RTC_BASE_ADDR                   0x44e3e000
set  RTC_KICK0R                      [expr       $RTC_BASE_ADDR      +  0x6c]
set  RTC_KICK1R                      [expr       $RTC_BASE_ADDR      +  0x70]


if { [info exists CHIPNAME] } {
   set _CHIPNAME $CHIPNAME
} else {
   set _CHIPNAME am437x
}

#
# M3 DAP
#
if { [info exists M3_DAP_TAPID] } {
        set _M3_DAP_TAPID $M3_DAP_TAPID
} else {
        set _M3_DAP_TAPID 0x4b6b902f
}
jtag newtap $_CHIPNAME m3_dap -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_M3_DAP_TAPID -disable
jtag configure $_CHIPNAME.m3_dap -event tap-enable "icepick_d_tapenable $_CHIPNAME.jrc 11"

#
# Cortex A9 DAP
#
if { [info exists DAP_TAPID] } {
   set _DAP_TAPID $DAP_TAPID
} else {
   set _DAP_TAPID 0x4b6b902f
}
jtag newtap $_CHIPNAME dap -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_DAP_TAPID -disable
jtag configure $_CHIPNAME.dap -event tap-enable "icepick_d_tapenable $_CHIPNAME.jrc 12"

#
# ICEpick-D (JTAG route controller)
#
if { [info exists JRC_TAPID] } {
   set _JRC_TAPID $JRC_TAPID
} else {
   set _JRC_TAPID 0x0b98c02f
}
jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID -ignore-version
jtag configure $_CHIPNAME.jrc -event setup "jtag tapenable $_CHIPNAME.dap"
# some TCK tycles are required to activate the DEBUG power domain
jtag configure $_CHIPNAME.jrc -event post-reset "runtest 100"

#
# Cortex A9 target
#
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_a -chain-position $_CHIPNAME.dap -dbgbase 0x80000000

# SRAM: 256K at 0x4030.0000
$_TARGETNAME configure -work-area-phys 0x40300000 -work-area-size 0x40000

# Disables watchdog timer after reset otherwise board won't stay in
# halted state.
proc disable_watchdog { } {
        global WDT1_WSPR
        global WDT1_W_PEND_WSPR
        global _TARGETNAME

        set curstate [$_TARGETNAME curstate]

        if { [string compare $curstate halted] == 0 } {
                set WDT_DISABLE_SEQ1    0xaaaa
                set WDT_DISABLE_SEQ2    0x5555

                mww phys $WDT1_WSPR $WDT_DISABLE_SEQ1

                # Empty body to make sure this executes as fast as possible.
                # We don't want any delays here otherwise romcode might start
                # executing and end up changing state of certain IPs.
                while { [expr [mrw $WDT1_W_PEND_WSPR] & 0x10] } { }

                mww phys $WDT1_WSPR $WDT_DISABLE_SEQ2
                while { [expr [mrw $WDT1_W_PEND_WSPR] & 0x10] } { }
        }
}

$_TARGETNAME configure -event reset-start { adapter_khz 1000 }
$_TARGETNAME configure -event reset-end { disable_watchdog }