[PATCH] Clean up Katmai (440SPe) linker script

[u-boot] / README

diff --git a/README b/README
index 6b94f8482c5c55816a9d878c006d1d64f641aa0b..15428643edef7ea77710113f8908002b50328577 100644 (file)
--- a/README
+++ b/README
@@ -1342,6 +1342,27 @@ The following options need to be configured:
 
                will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
 
 
                will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
 

+               CFG_SPD_BUS_NUM
+
+               If defined, then this indicates the I2C bus number for DDR SPD.
+               If not defined, then U-Boot assumes that SPD is on I2C bus 0.
+
+               CFG_RTC_BUS_NUM
+
+               If defined, then this indicates the I2C bus number for the RTC.
+               If not defined, then U-Boot assumes that RTC is on I2C bus 0.
+
+               CFG_DTT_BUS_NUM
+
+               If defined, then this indicates the I2C bus number for the DTT.
+               If not defined, then U-Boot assumes that DTT is on I2C bus 0.
+
+               CONFIG_FSL_I2C
+
+               Define this option if you want to use Freescale's I2C driver in
+               drivers/fsl_i2c.c.
+
+

 - SPI Support: CONFIG_SPI
 
                Enables SPI driver (so far only tested with
 - SPI Support: CONFIG_SPI
 
                Enables SPI driver (so far only tested with


@@ -1500,8 +1521,8 @@ The following options need to be configured:
 
                Enable auto completion of commands using TAB.
 
 
                Enable auto completion of commands using TAB.
 

-                Note that this feature has NOT been implemented yet
-                for the "hush" shell.
+               Note that this feature has NOT been implemented yet
+               for the "hush" shell.

 
 
                CFG_HUSH_PARSER
 
 
                CFG_HUSH_PARSER


@@ -2249,6 +2270,14 @@ Low Level (hardware related) configuration options:
                If SPD EEPROM is on an I2C bus other than the first one, specify here.
                Note that the value must resolve to something your driver can deal with.
 
                If SPD EEPROM is on an I2C bus other than the first one, specify here.
                Note that the value must resolve to something your driver can deal with.
 

+- CFG_83XX_DDR_USES_CS0
+               Only for 83xx systems. If specified, then DDR should be configured
+               using CS0 and CS1 instead of CS2 and CS3.
+
+- CFG_83XX_DDR_USES_CS0
+               Only for 83xx systems. If specified, then DDR should be configured
+               using CS0 and CS1 instead of CS2 and CS3.
+

 - CONFIG_ETHER_ON_FEC[12]
                Define to enable FEC[12] on a 8xx series processor.
 
 - CONFIG_ETHER_ON_FEC[12]
                Define to enable FEC[12] on a 8xx series processor.
 


@@ -3154,11 +3183,11 @@ loadaddr=200000
 oftaddr=0x300000
 => bootm $loadaddr - $oftaddr
 ## Booting image at 00200000 ...
 oftaddr=0x300000
 => bootm $loadaddr - $oftaddr
 ## Booting image at 00200000 ...

-   Image Name:   Linux-2.6.17-dirty
-   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
-   Data Size:    1029343 Bytes = 1005.2 kB
+   Image Name:  Linux-2.6.17-dirty
+   Image Type:  PowerPC Linux Kernel Image (gzip compressed)
+   Data Size:   1029343 Bytes = 1005.2 kB

    Load Address: 00000000
    Load Address: 00000000

-   Entry Point:  00000000
+   Entry Point:         00000000

    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK
 Booting using flat device tree at 0x300000
    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK
 Booting using flat device tree at 0x300000