arm: socfpga: Enable simple bus in SPL on all boards

[u-boot] / README

diff --git a/README b/README
index 63bdeb9930aeccc1dde1801845aa04609696698f..43f307f30fd8ce3b1fd5a0ee098399e7ff2bb2f4 100644 (file)
--- a/README
+++ b/README
@@ -611,6 +611,9 @@ The following options need to be configured:
                CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
                Number of controllers used for other than main memory.
 
                CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
                Number of controllers used for other than main memory.
 

+               CONFIG_SYS_FSL_HAS_DP_DDR
+               Defines the SoC has DP-DDR used for DPAA.
+

                CONFIG_SYS_FSL_SEC_BE
                Defines the SEC controller register space as Big Endian
 
                CONFIG_SYS_FSL_SEC_BE
                Defines the SEC controller register space as Big Endian
 


@@ -867,18 +870,11 @@ The following options need to be configured:
                                                (0-5, cf. cfb_console.c)
                        VIDEO_FB_ADRS           framebuffer address
                        VIDEO_KBD_INIT_FCT      keyboard int fct
                                                (0-5, cf. cfb_console.c)
                        VIDEO_FB_ADRS           framebuffer address
                        VIDEO_KBD_INIT_FCT      keyboard int fct

-                                               (i.e. i8042_kbd_init())
+                                               (i.e. rx51_kp_init())

                        VIDEO_TSTC_FCT          test char fct
                        VIDEO_TSTC_FCT          test char fct

-                                               (i.e. i8042_tstc)
+                                               (i.e. rx51_kp_tstc)

                        VIDEO_GETC_FCT          get char fct
                        VIDEO_GETC_FCT          get char fct

-                                               (i.e. i8042_getc)
-                       CONFIG_CONSOLE_CURSOR   cursor drawing on/off
-                                               (requires blink timer
-                                               cf. i8042.c)
-                       CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
-                       CONFIG_CONSOLE_TIME     display time/date info in
-                                               upper right corner
-                                               (requires CONFIG_CMD_DATE)
+                                               (i.e. rx51_kp_getc)

                        CONFIG_VIDEO_LOGO       display Linux logo in
                                                upper left corner
                        CONFIG_VIDEO_BMP_LOGO   use bmp_logo.h instead of
                        CONFIG_VIDEO_LOGO       display Linux logo in
                                                upper left corner
                        CONFIG_VIDEO_BMP_LOGO   use bmp_logo.h instead of


@@ -1774,21 +1770,15 @@ CBFS (Coreboot Filesystem) support
                a default value of 65536 will be defined.
 
 - Keyboard Support:
                a default value of 65536 will be defined.
 
 - Keyboard Support:

-               CONFIG_ISA_KEYBOARD
-
-               Define this to enable standard (PC-Style) keyboard
-               support
+               See Kconfig help for available keyboard drivers.

 
 

-               CONFIG_I8042_KBD
-               Standard PC keyboard driver with US (is default) and
-               GERMAN key layout (switch via environment 'keymap=de') support.
-               Export function i8042_kbd_init, i8042_tstc and i8042_getc
-               for cfb_console. Supports cursor blinking.
+               CONFIG_KEYBOARD

 
 

-               CONFIG_CROS_EC_KEYB
-               Enables a Chrome OS keyboard using the CROS_EC interface.
-               This uses CROS_EC to communicate with a second microcontroller
-               which provides key scans on request.
+               Define this to enable a custom keyboard support.
+               This simply calls drv_keyboard_init() which must be
+               defined in your board-specific files. This option is deprecated
+               and is only used by novena. For new boards, use driver model
+               instead.

 
 - Video support:
                CONFIG_VIDEO
 
 - Video support:
                CONFIG_VIDEO


@@ -1849,15 +1839,6 @@ CBFS (Coreboot Filesystem) support
                boot.  See the documentation file README.video for a
                description of this variable.
 
                boot.  See the documentation file README.video for a
                description of this variable.
 

-
-- Keyboard Support:
-               CONFIG_KEYBOARD
-
-               Define this to enable a custom keyboard support.
-               This simply calls drv_keyboard_init() which must be
-               defined in your board-specific files.
-               The only board using this so far is RBC823.
-

 - LCD Support: CONFIG_LCD
 
                Define this to enable LCD support (for output to LCD
 - LCD Support: CONFIG_LCD
 
                Define this to enable LCD support (for output to LCD


@@ -2438,6 +2419,15 @@ CBFS (Coreboot Filesystem) support
                  - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3
                  - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3
                  - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3
                  - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3
                  - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3
                  - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3

+                 - activate dual channel with CONFIG_SYS_I2C_IHS_DUAL
+                 - CONFIG_SYS_I2C_IHS_SPEED_0_1 speed channel 0_1
+                 - CONFIG_SYS_I2C_IHS_SLAVE_0_1 slave addr channel 0_1
+                 - CONFIG_SYS_I2C_IHS_SPEED_1_1 speed channel 1_1
+                 - CONFIG_SYS_I2C_IHS_SLAVE_1_1 slave addr channel 1_1
+                 - CONFIG_SYS_I2C_IHS_SPEED_2_1 speed channel 2_1
+                 - CONFIG_SYS_I2C_IHS_SLAVE_2_1 slave addr channel 2_1
+                 - CONFIG_SYS_I2C_IHS_SPEED_3_1 speed channel 3_1
+                 - CONFIG_SYS_I2C_IHS_SLAVE_3_1 slave addr channel 3_1

 
                additional defines:
 
 
                additional defines:
 


@@ -2705,11 +2695,6 @@ CBFS (Coreboot Filesystem) support
                Enables the driver for SPI controller on SuperH. Currently
                only SH7757 is supported.
 
                Enables the driver for SPI controller on SuperH. Currently
                only SH7757 is supported.
 

-               CONFIG_SPI_X
-
-               Enables extended (16-bit) SPI EEPROM addressing.
-               (symmetrical to CONFIG_I2C_X)
-

                CONFIG_SOFT_SPI
 
                Enables a software (bit-bang) SPI driver rather than
                CONFIG_SOFT_SPI
 
                Enables a software (bit-bang) SPI driver rather than


@@ -3494,6 +3479,10 @@ FIT uImage format:
                without a fastmap.
                default: 0
 
                without a fastmap.
                default: 0
 

+               CONFIG_MTD_UBI_FM_DEBUG
+               Enable UBI fastmap debug
+               default: 0
+

 - UBIFS support
                CONFIG_CMD_UBIFS
 
 - UBIFS support
                CONFIG_CMD_UBIFS
 


@@ -3564,6 +3553,9 @@ FIT uImage format:
 
                CONFIG_SYS_SPL_MALLOC_START
                Starting address of the malloc pool used in SPL.
 
                CONFIG_SYS_SPL_MALLOC_START
                Starting address of the malloc pool used in SPL.

+               When this option is set the full malloc is used in SPL and
+               it is set up by spl_init() and before that, the simple malloc()
+               can be used if CONFIG_SYS_MALLOC_F is defined.

 
                CONFIG_SYS_SPL_MALLOC_SIZE
                The size of the malloc pool used in SPL.
 
                CONFIG_SYS_SPL_MALLOC_SIZE
                The size of the malloc pool used in SPL.


@@ -3877,7 +3869,15 @@ Configuration Settings:
                Scratch address used by the alternate memory test
                You only need to set this if address zero isn't writeable
 
                Scratch address used by the alternate memory test
                You only need to set this if address zero isn't writeable
 

-- CONFIG_SYS_MEM_TOP_HIDE (PPC only):
+- CONFIG_SYS_MEM_RESERVE_SECURE
+               If defined, the size of CONFIG_SYS_MEM_RESERVE_SECURE memory
+               is substracted from total RAM and won't be reported to OS.
+               This memory can be used as secure memory. A variable
+               gd->secure_ram is used to track the location. In systems
+               the RAM base is not zero, or RAM is divided into banks,
+               this variable needs to be recalcuated to get the address.
+
+- CONFIG_SYS_MEM_TOP_HIDE:

                If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
                this specified memory area will get subtracted from the top
                (end) of RAM and won't get "touched" at all by U-Boot. By
                If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
                this specified memory area will get subtracted from the top
                (end) of RAM and won't get "touched" at all by U-Boot. By


@@ -5056,8 +5056,8 @@ This firmware often needs to be loaded during U-Boot booting.
 - CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE
        Define minimum DDR size required for debug server image
 
 - CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE
        Define minimum DDR size required for debug server image
 

-- CONFIG_SYS_MEM_TOP_HIDE_MIN
-       Define minimum DDR size to be hided from top of the DDR memory
+- CONFIG_SYS_MC_RSV_MEM_ALIGN
+       Define alignment of reserved memory MC requires

 
 Reproducible builds
 -------------------
 
 Reproducible builds
 -------------------


@@ -5450,10 +5450,10 @@ List of environment variables (most likely not complete):
                  unset, then it will be made silent if the U-Boot console
                  is silent.
 
                  unset, then it will be made silent if the U-Boot console
                  is silent.
 

-  tftpsrcport  - If this is set, the value is used for TFTP's
+  tftpsrcp     - If this is set, the value is used for TFTP's

                  UDP source port.
 
                  UDP source port.
 

-  tftpdstport  - If this is set, the value is used for TFTP's UDP
+  tftpdstp     - If this is set, the value is used for TFTP's UDP

                  destination port instead of the Well Know Port 69.
 
   tftpblocksize - Block size to use for TFTP transfers; if not set,
                  destination port instead of the Well Know Port 69.
 
   tftpblocksize - Block size to use for TFTP transfers; if not set,


@@ -5467,6 +5467,14 @@ List of environment variables (most likely not complete):
                  faster in networks with high packet loss rates or
                  with unreliable TFTP servers.
 
                  faster in networks with high packet loss rates or
                  with unreliable TFTP servers.
 

+  tftptimeoutcountmax  - maximum count of TFTP timeouts (no
+                 unit, minimum value = 0). Defines how many timeouts
+                 can happen during a single file transfer before that
+                 transfer is aborted. The default is 10, and 0 means
+                 'no timeouts allowed'. Increasing this value may help
+                 downloads succeed with high packet loss rates, or with
+                 unreliable TFTP servers or client hardware.
+

   vlan         - When set to a value < 4095 the traffic over
                  Ethernet is encapsulated/received over 802.1q
                  VLAN tagged frames.
   vlan         - When set to a value < 4095 the traffic over
                  Ethernet is encapsulated/received over 802.1q
                  VLAN tagged frames.