sandbox: config: enable fdt and snprintf() options

[u-boot] / README

diff --git a/README b/README
index 43430576b2eface9929e3a08b5c0c8697ce6a8a1..89646725a0b884c5b8b10e4262a1682478788a29 100644 (file)
--- a/README
+++ b/README
@@ -420,6 +420,12 @@ The following options need to be configured:
                XWAY SoCs for booting from NOR flash. The U-Boot image needs to
                be swapped if a flash programmer is used.
 
                XWAY SoCs for booting from NOR flash. The U-Boot image needs to
                be swapped if a flash programmer is used.
 

+- ARM options:
+               CONFIG_SYS_EXCEPTION_VECTORS_HIGH
+
+               Select high exception vectors of the ARM core, e.g., do not
+               clear the V bit of the c1 register of CP15.
+

 - Linux Kernel Interface:
                CONFIG_CLOCKS_IN_MHZ
 
 - Linux Kernel Interface:
                CONFIG_CLOCKS_IN_MHZ
 


@@ -809,6 +815,7 @@ The following options need to be configured:
                                          (requires CONFIG_CMD_I2C)
                CONFIG_CMD_SETGETDCR      Support for DCR Register access
                                          (4xx only)
                                          (requires CONFIG_CMD_I2C)
                CONFIG_CMD_SETGETDCR      Support for DCR Register access
                                          (4xx only)

+               CONFIG_CMD_SF           * Read/write/erase SPI NOR flash

                CONFIG_CMD_SHA1SUM        print sha1 memory digest
                                          (requires CONFIG_CMD_MEMORY)
                CONFIG_CMD_SOURCE         "source" command Support
                CONFIG_CMD_SHA1SUM        print sha1 memory digest
                                          (requires CONFIG_CMD_MEMORY)
                CONFIG_CMD_SOURCE         "source" command Support


@@ -2191,6 +2198,25 @@ The following options need to be configured:
                allows to read/write in Dataflash via the standard
                commands cp, md...
 
                allows to read/write in Dataflash via the standard
                commands cp, md...
 

+- Serial Flash support
+               CONFIG_CMD_SF
+
+               Defining this option enables SPI flash commands
+               'sf probe/read/write/erase/update'.
+
+               Usage requires an initial 'probe' to define the serial
+               flash parameters, followed by read/write/erase/update
+               commands.
+
+               The following defaults may be provided by the platform
+               to handle the common case when only a single serial
+               flash is present on the system.
+
+               CONFIG_SF_DEFAULT_BUS           Bus identifier
+               CONFIG_SF_DEFAULT_CS            Chip-select
+               CONFIG_SF_DEFAULT_MODE          (see include/spi.h)
+               CONFIG_SF_DEFAULT_SPEED         in Hz
+

 - SystemACE Support:
                CONFIG_SYSTEMACE
 
 - SystemACE Support:
                CONFIG_SYSTEMACE
 


@@ -3639,6 +3665,14 @@ List of environment variables (most likely not complete):
 
   fdt_high     - if set this restricts the maximum address that the
                  flattened device tree will be copied into upon boot.
 
   fdt_high     - if set this restricts the maximum address that the
                  flattened device tree will be copied into upon boot.

+                 For example, if you have a system with 1 GB memory
+                 at physical address 0x10000000, while Linux kernel
+                 only recognizes the first 704 MB as low memory, you
+                 may need to set fdt_high as 0x3C000000 to have the
+                 device tree blob be copied to the maximum address
+                 of the 704 MB low memory, so that Linux kernel can
+                 access it during the boot procedure.
+

                  If this is set to the special value 0xFFFFFFFF then
                  the fdt will not be copied at all on boot.  For this
                  to work it must reside in writable memory, have
                  If this is set to the special value 0xFFFFFFFF then
                  the fdt will not be copied at all on boot.  For this
                  to work it must reside in writable memory, have