Exynos: config: Enable hash command

[u-boot] / README

diff --git a/README b/README
index ac61a32adf33c471887111515a9d677a902d4146..a35ef318da100b51f66c5515f6660fa2014ed90a 100644 (file)
--- a/README
+++ b/README
@@ -485,6 +485,17 @@ The following options need to be configured:
                Thumb2 this flag will result in Thumb2 code generated by
                GCC.
 
                Thumb2 this flag will result in Thumb2 code generated by
                GCC.
 

+               CONFIG_ARM_ERRATA_716044
+               CONFIG_ARM_ERRATA_742230
+               CONFIG_ARM_ERRATA_743622
+               CONFIG_ARM_ERRATA_751472
+
+               If set, the workarounds for these ARM errata are applied early
+               during U-Boot startup. Note that these options force the
+               workarounds to be applied; no CPU-type/version detection
+               exists, unlike the similar options in the Linux kernel. Do not
+               set these options unless they apply!
+

 - Linux Kernel Interface:
                CONFIG_CLOCKS_IN_MHZ
 
 - Linux Kernel Interface:
                CONFIG_CLOCKS_IN_MHZ
 


@@ -616,6 +627,14 @@ The following options need to be configured:
                boot loader that has already initialized the UART.  Define this
                variable to flush the UART at init time.
 
                boot loader that has already initialized the UART.  Define this
                variable to flush the UART at init time.
 

+               CONFIG_SYS_NS16550_BROKEN_TEMT
+
+               16550 UART set the Transmitter Empty (TEMT) Bit when all output
+               has finished and the transmitter is totally empty. U-Boot waits
+               for this bit to be set to initialize the serial console. On some
+               broken platforms this bit is not set in SPL making U-Boot to
+               hang while waiting for TEMT. Define this option to avoid it.
+

 
 - Console Interface:
                Depending on board, define exactly one serial port
 
 - Console Interface:
                Depending on board, define exactly one serial port


@@ -816,6 +835,7 @@ The following options need to be configured:
                CONFIG_CMD_EEPROM       * EEPROM read/write support
                CONFIG_CMD_ELF          * bootelf, bootvx
                CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
                CONFIG_CMD_EEPROM       * EEPROM read/write support
                CONFIG_CMD_ELF          * bootelf, bootvx
                CONFIG_CMD_ENV_CALLBACK * display details about env callbacks

+               CONFIG_CMD_ENV_FLAGS    * display details about env flags

                CONFIG_CMD_EXPORTENV    * export the environment
                CONFIG_CMD_EXT2         * ext2 command support
                CONFIG_CMD_EXT4         * ext4 command support
                CONFIG_CMD_EXPORTENV    * export the environment
                CONFIG_CMD_EXT2         * ext2 command support
                CONFIG_CMD_EXT4         * ext4 command support


@@ -833,7 +853,8 @@ The following options need to be configured:
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support
                CONFIG_CMD_IMI            iminfo
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support
                CONFIG_CMD_IMI            iminfo

-               CONFIG_CMD_IMLS           List all found images
+               CONFIG_CMD_IMLS           List all images found in NOR flash
+               CONFIG_CMD_IMLS_NAND      List all images found in NAND flash

                CONFIG_CMD_IMMAP        * IMMR dump support
                CONFIG_CMD_IMPORTENV    * import an environment
                CONFIG_CMD_INI          * import data from an ini file into the env
                CONFIG_CMD_IMMAP        * IMMR dump support
                CONFIG_CMD_IMPORTENV    * import an environment
                CONFIG_CMD_INI          * import data from an ini file into the env


@@ -848,8 +869,10 @@ The following options need to be configured:
                CONFIG_CMD_LOADS          loads
                CONFIG_CMD_MD5SUM         print md5 message digest
                                          (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
                CONFIG_CMD_LOADS          loads
                CONFIG_CMD_MD5SUM         print md5 message digest
                                          (requires CONFIG_CMD_MEMORY and CONFIG_MD5)

+               CONFIG_CMD_MEMINFO      * Display detailed memory information

                CONFIG_CMD_MEMORY         md, mm, nm, mw, cp, cmp, crc, base,
                CONFIG_CMD_MEMORY         md, mm, nm, mw, cp, cmp, crc, base,

-                                         loop, loopw, mtest
+                                         loop, loopw
+               CONFIG_CMD_MEMTEST        mtest

                CONFIG_CMD_MISC           Misc functions like sleep etc
                CONFIG_CMD_MMC          * MMC memory mapped support
                CONFIG_CMD_MII          * MII utility commands
                CONFIG_CMD_MISC           Misc functions like sleep etc
                CONFIG_CMD_MMC          * MMC memory mapped support
                CONFIG_CMD_MII          * MII utility commands


@@ -866,6 +889,7 @@ The following options need to be configured:
                CONFIG_CMD_READ         * Read raw data from partition
                CONFIG_CMD_REGINFO      * Register dump
                CONFIG_CMD_RUN            run command in env variable
                CONFIG_CMD_READ         * Read raw data from partition
                CONFIG_CMD_REGINFO      * Register dump
                CONFIG_CMD_RUN            run command in env variable

+               CONFIG_CMD_SANDBOX      * sb command to access sandbox features

                CONFIG_CMD_SAVES        * save S record dump
                CONFIG_CMD_SCSI         * SCSI Support
                CONFIG_CMD_SDRAM        * print SDRAM configuration information
                CONFIG_CMD_SAVES        * save S record dump
                CONFIG_CMD_SCSI         * SCSI Support
                CONFIG_CMD_SDRAM        * print SDRAM configuration information


@@ -1485,6 +1509,21 @@ CBFS (Coreboot Filesystem) support
                Normally display is black on white background; define
                CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
 
                Normally display is black on white background; define
                CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
 

+               CONFIG_LCD_ALIGNMENT
+
+               Normally the LCD is page-aligned (tyically 4KB). If this is
+               defined then the LCD will be aligned to this value instead.
+               For ARM it is sometimes useful to use MMU_SECTION_SIZE
+               here, since it is cheaper to change data cache settings on
+               a per-section basis.
+
+               CONFIG_CONSOLE_SCROLL_LINES
+
+               When the console need to be scrolled, this is the number of
+               lines to scroll by. It defaults to 1. Increasing this makes
+               the console jump but can help speed up operation when scrolling
+               is slow.
+

                CONFIG_LCD_BMP_RLE8
 
                Support drawing of RLE8-compressed bitmaps on the LCD.
                CONFIG_LCD_BMP_RLE8
 
                Support drawing of RLE8-compressed bitmaps on the LCD.


@@ -1494,7 +1533,6 @@ CBFS (Coreboot Filesystem) support
                Enables an 'i2c edid' command which can read EDID
                information over I2C from an attached LCD display.
 
                Enables an 'i2c edid' command which can read EDID
                information over I2C from an attached LCD display.
 

-

 - Splash Screen Support: CONFIG_SPLASH_SCREEN
 
                If this option is set, the environment is checked for
 - Splash Screen Support: CONFIG_SPLASH_SCREEN
 
                If this option is set, the environment is checked for


@@ -1506,6 +1544,17 @@ CBFS (Coreboot Filesystem) support
                allows for a "silent" boot where a splash screen is
                loaded very quickly after power-on.
 
                allows for a "silent" boot where a splash screen is
                loaded very quickly after power-on.
 

+               CONFIG_SPLASHIMAGE_GUARD
+
+               If this option is set, then U-Boot will prevent the environment
+               variable "splashimage" from being set to a problematic address
+               (see README.displaying-bmps and README.arm-unaligned-accesses).
+               This option is useful for targets where, due to alignment
+               restrictions, an improperly aligned BMP image will cause a data
+               abort. If you think you will not have problems with unaligned
+               accesses (for example because your toolchain prevents them)
+               there is no need to set this option.
+

                CONFIG_SPLASH_SCREEN_ALIGN
 
                If this option is set the splash image can be freely positioned
                CONFIG_SPLASH_SCREEN_ALIGN
 
                If this option is set the splash image can be freely positioned


@@ -1526,6 +1575,14 @@ CBFS (Coreboot Filesystem) support
                        => vertically centered image
                           at x = dspWidth - bmpWidth - 9
 
                        => vertically centered image
                           at x = dspWidth - bmpWidth - 9
 

+               CONFIG_SPLASH_SCREEN_PREPARE
+
+               If this option is set then the board_splash_screen_prepare()
+               function, which must be defined in your code, is called as part
+               of the splash screen display sequence. It gives the board an
+               opportunity to prepare the splash image data before it is
+               processed and sent to the frame buffer by U-Boot.
+

 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
 
                If this option is set, additionally to standard BMP
 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
 
                If this option is set, additionally to standard BMP


@@ -2188,6 +2245,11 @@ CBFS (Coreboot Filesystem) support
                serial# is unaffected by this, i. e. it remains
                read-only.]
 
                serial# is unaffected by this, i. e. it remains
                read-only.]
 

+               The same can be accomplished in a more flexible way
+               for any variable by configuring the type of access
+               to allow for those variables in the ".flags" variable
+               or define CONFIG_ENV_FLAGS_LIST_STATIC.
+

 - Protected RAM:
                CONFIG_PRAM
 
 - Protected RAM:
                CONFIG_PRAM
 


@@ -2358,6 +2420,15 @@ CBFS (Coreboot Filesystem) support
                run-time determined information about the hardware to the
                environment.  These will be named board_name, board_rev.
 
                run-time determined information about the hardware to the
                environment.  These will be named board_name, board_rev.
 

+               CONFIG_DELAY_ENVIRONMENT
+
+               Normally the environment is loaded when the board is
+               intialised so that it is available to U-Boot. This inhibits
+               that so that the environment is not available until
+               explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
+               this is instead controlled by the value of
+               /config/load-environment.
+

 - DataFlash Support:
                CONFIG_HAS_DATAFLASH
 
 - DataFlash Support:
                CONFIG_HAS_DATAFLASH
 


@@ -2384,6 +2455,11 @@ CBFS (Coreboot Filesystem) support
                CONFIG_SF_DEFAULT_MODE          (see include/spi.h)
                CONFIG_SF_DEFAULT_SPEED         in Hz
 
                CONFIG_SF_DEFAULT_MODE          (see include/spi.h)
                CONFIG_SF_DEFAULT_SPEED         in Hz
 

+               CONFIG_CMD_SF_TEST
+
+               Define this option to include a destructive SPI flash
+               test ('sf test').
+

 - SystemACE Support:
                CONFIG_SYSTEMACE
 
 - SystemACE Support:
                CONFIG_SYSTEMACE
 


@@ -2671,10 +2747,13 @@ FIT uImage format:
                CONFIG_FB_ADDR
 
                Define CONFIG_FB_ADDR if you want to use specific
                CONFIG_FB_ADDR
 
                Define CONFIG_FB_ADDR if you want to use specific

-               address for frame buffer.
-               Then system will reserve the frame buffer address to
-               defined address instead of lcd_setmem (this function
-               grabs the memory for frame buffer by panel's size).
+               address for frame buffer.  This is typically the case
+               when using a graphics controller has separate video
+               memory.  U-Boot will then place the frame buffer at
+               the given address instead of dynamically reserving it
+               in system RAM by calling lcd_setmem(), which grabs
+               the memory for the frame buffer depending on the
+               configured panel size.

 
                Please see board_init_f function.
 
 
                Please see board_init_f function.
 


@@ -2773,6 +2852,12 @@ FIT uImage format:
                CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
                Filename to read to load U-Boot when reading from FAT
 
                CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
                Filename to read to load U-Boot when reading from FAT
 

+               CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
+               Set this for NAND SPL on PPC mpc83xx targets, so that
+               start.S waits for the rest of the SPL to load before
+               continuing (the hardware starts execution after just
+               loading the first page rather than the full 4K).
+

                CONFIG_SPL_NAND_BASE
                Include nand_base.c in the SPL.  Requires
                CONFIG_SPL_NAND_DRIVERS.
                CONFIG_SPL_NAND_BASE
                Include nand_base.c in the SPL.  Requires
                CONFIG_SPL_NAND_DRIVERS.


@@ -2830,6 +2915,10 @@ FIT uImage format:
                CONFIG_SPL_LIBGENERIC_SUPPORT
                Support for lib/libgeneric.o in SPL binary
 
                CONFIG_SPL_LIBGENERIC_SUPPORT
                Support for lib/libgeneric.o in SPL binary
 

+               CONFIG_SPL_PAD_TO
+               Linker address to which the SPL should be padded before
+               appending the SPL payload.
+

                CONFIG_SPL_TARGET
                Final target image containing SPL and payload.  Some SPLs
                use an arch-specific makefile fragment instead, for
                CONFIG_SPL_TARGET
                Final target image containing SPL and payload.  Some SPLs
                use an arch-specific makefile fragment instead, for


@@ -2969,9 +3058,6 @@ Configuration Settings:
                non page size aligned address and this could cause major
                problems.
 
                non page size aligned address and this could cause major
                problems.
 

-- CONFIG_SYS_TFTP_LOADADDR:
-               Default load address for network file downloads
-

 - CONFIG_SYS_LOADS_BAUD_CHANGE:
                Enable temporary baudrate change while serial download
 
 - CONFIG_SYS_LOADS_BAUD_CHANGE:
                Enable temporary baudrate change while serial download
 


@@ -3113,6 +3199,66 @@ Configuration Settings:
        cases. This setting can be used to tune behaviour; see
        lib/hashtable.c for details.
 
        cases. This setting can be used to tune behaviour; see
        lib/hashtable.c for details.
 

+- CONFIG_ENV_FLAGS_LIST_DEFAULT
+- CONFIG_ENV_FLAGS_LIST_STATIC
+       Enable validation of the values given to enviroment variables when
+       calling env set.  Variables can be restricted to only decimal,
+       hexadecimal, or boolean.  If CONFIG_CMD_NET is also defined,
+       the variables can also be restricted to IP address or MAC address.
+
+       The format of the list is:
+               type_attribute = [s|d|x|b|i|m]
+               access_atribute = [a|r|o|c]
+               attributes = type_attribute[access_atribute]
+               entry = variable_name[:attributes]
+               list = entry[,list]
+
+       The type attributes are:
+               s - String (default)
+               d - Decimal
+               x - Hexadecimal
+               b - Boolean ([1yYtT|0nNfF])
+               i - IP address
+               m - MAC address
+
+       The access attributes are:
+               a - Any (default)
+               r - Read-only
+               o - Write-once
+               c - Change-default
+
+       - CONFIG_ENV_FLAGS_LIST_DEFAULT
+               Define this to a list (string) to define the ".flags"
+               envirnoment variable in the default or embedded environment.
+
+       - CONFIG_ENV_FLAGS_LIST_STATIC
+               Define this to a list (string) to define validation that
+               should be done if an entry is not found in the ".flags"
+               environment variable.  To override a setting in the static
+               list, simply add an entry for the same variable name to the
+               ".flags" variable.
+
+- CONFIG_ENV_ACCESS_IGNORE_FORCE
+       If defined, don't allow the -f switch to env set override variable
+       access flags.
+
+- CONFIG_SYS_GENERIC_BOARD
+       This selects the architecture-generic board system instead of the
+       architecture-specific board files. It is intended to move boards
+       to this new framework over time. Defining this will disable the
+       arch/foo/lib/board.c file and use common/board_f.c and
+       common/board_r.c instead. To use this option your architecture
+       must support it (i.e. must define __HAVE_ARCH_GENERIC_BOARD in
+       its config.mk file). If you find problems enabling this option on
+       your board please report the problem and send patches!
+
+- CONFIG_SYS_SYM_OFFSETS
+       This is set by architectures that use offsets for link symbols
+       instead of absolute values. So bss_start is obtained using an
+       offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
+       directly. You should not need to touch this setting.
+
+

 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
 following configurations:
 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
 following configurations:


@@ -3388,6 +3534,16 @@ use the "saveenv" command to store a valid environment.
                space for already greatly restricted images, including but not
                limited to NAND_SPL configurations.
 
                space for already greatly restricted images, including but not
                limited to NAND_SPL configurations.
 

+- CONFIG_DISPLAY_BOARDINFO
+               Display information about the board that U-Boot is running on
+               when U-Boot starts up. The board function checkboard() is called
+               to do this.
+
+- CONFIG_DISPLAY_BOARDINFO_LATE
+               Similar to the previous option, but display this information
+               later, once stdio is running and output goes to the LCD, if
+               present.
+

 Low Level (hardware related) configuration options:
 ---------------------------------------------------
 
 Low Level (hardware related) configuration options:
 ---------------------------------------------------
 


@@ -3704,21 +3860,29 @@ Low Level (hardware related) configuration options:
                that is executed before the actual U-Boot. E.g. when
                compiling a NAND SPL.
 
                that is executed before the actual U-Boot. E.g. when
                compiling a NAND SPL.
 

+- CONFIG_ARCH_MAP_SYSMEM
+               Generally U-Boot (and in particular the md command) uses
+               effective address. It is therefore not necessary to regard
+               U-Boot address as virtual addresses that need to be translated
+               to physical addresses. However, sandbox requires this, since
+               it maintains its own little RAM buffer which contains all
+               addressable memory. This option causes some memory accesses
+               to be mapped through map_sysmem() / unmap_sysmem().
+

 - CONFIG_USE_ARCH_MEMCPY
   CONFIG_USE_ARCH_MEMSET
                If these options are used a optimized version of memcpy/memset will
                be used if available. These functions may be faster under some
                conditions but may increase the binary size.
 
 - CONFIG_USE_ARCH_MEMCPY
   CONFIG_USE_ARCH_MEMSET
                If these options are used a optimized version of memcpy/memset will
                be used if available. These functions may be faster under some
                conditions but may increase the binary size.
 

-- CONFIG_X86_NO_RESET_VECTOR
-               If defined, the x86 reset vector code is excluded. You will need
-               to do this when U-Boot is running from Coreboot.
+- CONFIG_X86_RESET_VECTOR
+               If defined, the x86 reset vector code is included. This is not
+               needed when U-Boot is running from Coreboot.

 
 

-- CONFIG_X86_NO_REAL_MODE
-               If defined, x86 real mode code is omitted. This assumes a
-               32-bit environment where such code is not needed. You will
-               need to do this when U-Boot is running from Coreboot.
+- CONFIG_SYS_MPUCLK
+               Defines the MPU clock speed (in MHz).

 
 

+               NOTE : currently only supported on AM335x platforms.

 
 Freescale QE/FMAN Firmware Support:
 -----------------------------------
 
 Freescale QE/FMAN Firmware Support:
 -----------------------------------