-
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
-#ifdef CONFIG_NAND_SPL /* deprecated, use instead CONFIG_SPL_BUILD */
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
-#else
-#ifdef CONFIG_SPL_BUILD
- ldr sp, =(CONFIG_SPL_STACK)
-#else
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
-#endif
-#endif
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
-
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- sub r9, r6, r0 /* r9 <- relocation offset */
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifdef CONFIG_SPL_BUILD
- /* No relocation for SPL */
- ldr r0, =__bss_start
- ldr r1, =__bss_end__
-#else
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4