- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- return 0;
-}
-#endif
-
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB3 devices to 0.
- | Set PLB3 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB4 devices to 0.
- +-------------------------------------------------------------------------*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
-
- /*-------------------------------------------------------------------------+
- | Set Nebula PLB4 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- /* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
-
- /* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440 EP PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CFG_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
-
-/*************************************************************************
- * pci_master_init
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*--------------------------------------------------------------------------+
- | Write the PowerPC440 EP PCI Configuration regs.
- | Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- | Enable PowerPC440 EP to act as a PCI memory target (PTM).
- +--------------------------------------------------------------------------*/
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */
-
-/*************************************************************************
- * is_pci_host
- *
- * This routine is called to determine if a pci scan should be
- * performed. With various hardware environments (especially cPCI and
- * PPMC) it's insufficient to depend on the state of the arbiter enable
- * bit in the strap register, or generic host/adapter assumptions.
- *
- * Rather than hard-code a bad assumption in the general 440 code, the
- * 440 pci code requires the board to decide at runtime.
- *
- * Return 0 for adapter mode, non-zero for host (monarch) mode.
- *
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
- /* Bamboo is always configured as host. */
- return (1);