armv7: ls1021aqds: Set cpo_sample for erratum A-009942

[u-boot] / board / freescale / mx35pdk / README

diff --git a/board/freescale/mx35pdk/README b/board/freescale/mx35pdk/README
index 3d69ed5839ccc7a02d353273c7e38f853d659257..6f6841f0993b51b682bd2522ee43d5099049061c 100644 (file)
--- a/board/freescale/mx35pdk/README
+++ b/board/freescale/mx35pdk/README
@@ -71,91 +71,17 @@ exec -c "noinitrd console=ttymxc0,115200 root=/dev/nfsroot rootfstype=nfsroot nf
 Flashing U-Boot
 --------------------------------
 
 Flashing U-Boot
 --------------------------------
 

-There are two options: the original bootloader in NAND can be replaced with
-u-boot, or u-boot can be stored on the NOR flash without erasing
-the delivered bootloader.
+U-Boot should be stored on the NOR flash.
+

 The boot storage can be select using the switches on the personality board
 (SW1-SW2) and on the DEBUG board (SW4-SW10).
 
 The boot storage can be select using the switches on the personality board
 (SW1-SW2) and on the DEBUG board (SW4-SW10).
 

-The second option is to be preferred if you have not a JTAG debugger.

 If something goes wrong flashing the bootloader, it is always possible to
 recover the board booting from the other device.
 
 If something goes wrong flashing the bootloader, it is always possible to
 recover the board booting from the other device.
 

-Replacing the bootloader on the NAND
---------------------------------------
-To replace RedBoot with U-Boot, the easy way is to do this in linux.
-Start the kernel with the suggested options. Make sure to have set the
-mtdparts exactly as described, because this matches the layout on the
-mx35pdk.
-
-You should see in your boot log the following entries for the NAND
-flash:
-
-5 cmdlinepart partitions found on MTD device mxc_nand
-Creating 5 MTD partitions on "mxc_nand":
-0x000000000000-0x000000100000 : "boot"
-0x000000100000-0x000000600000 : "linux"
-0x000000600000-0x000006600000 : "root"
-0x000006600000-0x000006e00000 : "cfg"
-0x000006e00000-0x000080000000 : "user"
-
-You can use the utilities flash_eraseall and nandwrite to put
-u-boot on the NAND. The bootloader is marked as "boot", and 1MB is
-reserved. If everything is correct, this partition is accessed as
-/dev/mtd4. However, check if it is correct with "cat /proc/mtd" and
-get the device node from the partition name:
-
-$ cat /proc/mtd | grep boot
-
-I suggest you try the utilities on a different partition to be sure
-if everything works correctly. If not, and you remove RedBoot, you have to
-reinstall it using the ATK tool as suggested by Freescale, or using a
-JTAG debugger.
-
-I report the versions of the utilities I used (they are provided with ELDK):
-
--bash-3.2# nandwrite --version
-nandwrite $Revision: 1.32 $
-
-flash_eraseall --version
-flash_eraseall $Revision: 1.22 $
-
-nandwrite reports a warning if the file to be saved is not sector aligned.
-This should have no consequences, but I preferred to pad u-boot.bin
-to get no problem at all.
-$ dd if=/dev/zero of=zeros bs=1 count=74800
-$ cat u-boot.bin zeros > u-boot-padded.bin
-
-To erase the partition:
-$ flash_eraseall /dev/mtd4
-
-Writing u-boot:
-
-$ nandwrite /dev/mtd4 u-boot-padded.bin
-
-Now U-Boot is stored on the booting partition.
-
-To boot from NAND, you have to select the switches as follows:
-
-Personality board
-       SW2     1, 4, 5 on
-               2, 3, 6, 7, 8 off
-       SW1     all off
-
-Debug Board:
-       SW5     0
-       SW6     0
-       SW7     0
-       SW8     1
-       SW9     1
-       SW10    0
-
-

 Saving U-Boot in the NOR flash
 ---------------------------------
 
 Saving U-Boot in the NOR flash
 ---------------------------------
 

-The procedure to save in the NOR flash is quite the same as to write into the NAND.
-

 Check the partition for boot in the NOR flash. Setting the mtdparts as reported,
 the boot partition should be /dev/mtd0.
 
 Check the partition for boot in the NOR flash. Setting the mtdparts as reported,
 the boot partition should be /dev/mtd0.
 


@@ -170,7 +96,7 @@ Creating 6 MTD partitions on "mxc_nor_flash.0":
 To erase the whole partition:
 $ flash_eraseall /dev/mtd0
 
 To erase the whole partition:
 $ flash_eraseall /dev/mtd0
 

-Writing u-boot:
+Writing U-Boot:

 dd if=u-boot.bin of=/dev/mtd0
 
 To boot from NOR, you have to select the switches as follows:
 dd if=u-boot.bin of=/dev/mtd0
 
 To boot from NOR, you have to select the switches as follows: