Merge git://git.denx.de/u-boot-uniphier

[u-boot] / doc / README.nand

diff --git a/doc/README.nand b/doc/README.nand
index 46d7edd179f139bb9688bfe1557bd5cbbcc53daf..362b8d8c9f4d08c89c4ddfd5a394642a918e0666 100644 (file)
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -94,7 +94,7 @@ Configuration Options:
        address of u-boot MTD partition in NAND.
 
    CONFIG_CMD_NAND
        address of u-boot MTD partition in NAND.
 
    CONFIG_CMD_NAND

-      Enables NAND support and commmands.
+      Enables NAND support and commands.

 
    CONFIG_CMD_NAND_TORTURE
       Enables the torture command (see description of this command below).
 
    CONFIG_CMD_NAND_TORTURE
       Enables the torture command (see description of this command below).


@@ -136,15 +136,8 @@ Configuration Options:
       Example of new init to be added to the end of an existing driver
       init:
 
       Example of new init to be added to the end of an existing driver
       init:
 

-       /*
-        * devnum is the device number to be used in nand commands
-        * and in mtd->name.  Must be less than
-        * CONFIG_SYS_NAND_MAX_DEVICE.
-        */
-       mtd = &nand_info[devnum];
-

        /* chip is struct nand_chip, and is now provided by the driver. */
        /* chip is struct nand_chip, and is now provided by the driver. */

-       mtd->priv = &chip;
+       mtd = nand_to_mtd(&chip);

 
        /*
         * Fill in appropriate values if this driver uses these fields,
 
        /*
         * Fill in appropriate values if this driver uses these fields,


@@ -165,7 +158,11 @@ Configuration Options:
        if (nand_scan_tail(mtd))
                error out
 
        if (nand_scan_tail(mtd))
                error out
 

-       if (nand_register(devnum))
+       /*
+        * devnum is the device number to be used in nand commands
+        * and in mtd->name.  Must be less than CONFIG_SYS_MAX_NAND_DEVICE.
+        */
+       if (nand_register(devnum, mtd))

                error out
 
       In addition to providing more flexibility to the driver, it reduces
                error out
 
       In addition to providing more flexibility to the driver, it reduces


@@ -183,30 +180,6 @@ Configuration Options:
        And fetching device parameters flashed on device, by parsing
        ONFI parameter page.
 
        And fetching device parameters flashed on device, by parsing
        ONFI parameter page.
 

-   CONFIG_BCH
-       Enables software based BCH ECC algorithm present in lib/bch.c
-       This is used by SoC platforms which do not have built-in ELM
-       hardware engine required for BCH ECC correction.
-
-   CONFIG_SYS_NAND_BUSWIDTH_16BIT
-       Indicates that NAND device has 16-bit wide data-bus. In absence of this
-       config, bus-width of NAND device is assumed to be either 8-bit and later
-       determined by reading ONFI params.
-       Above config is useful when NAND device's bus-width information cannot
-       be determined from on-chip ONFI params, like in following scenarios:
-       - SPL boot does not support reading of ONFI parameters. This is done to
-         keep SPL code foot-print small.
-       - In current U-Boot flow using nand_init(), driver initialization
-         happens in board_nand_init() which is called before any device probe
-         (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are
-         not available while configuring controller. So a static CONFIG_NAND_xx
-         is needed to know the device's bus-width in advance.
-       Some drivers using above config are:
-       drivers/mtd/nand/mxc_nand.c
-       drivers/mtd/nand/ndfc.c
-       drivers/mtd/nand/omap_gpmc.c
-
-

 Platform specific options
 =========================
    CONFIG_NAND_OMAP_GPMC
 Platform specific options
 =========================
    CONFIG_NAND_OMAP_GPMC


@@ -292,7 +265,7 @@ Platform specific options
 
                However, for 4K pagesize NAND
                NAND_PAGESIZE = 4096
 
                However, for 4K pagesize NAND
                NAND_PAGESIZE = 4096

-               NAND_OOBSIZE = 64
+               NAND_OOBSIZE = 224

                ECC_BYTES = 26
                2 + (4096 / 512) * 26 = 210 < NAND_OOBSIZE
                Thus BCH16 can be supported on 4K page NAND.
                ECC_BYTES = 26
                2 + (4096 / 512) * 26 = 210 < NAND_OOBSIZE
                Thus BCH16 can be supported on 4K page NAND.


@@ -328,7 +301,7 @@ Miscellaneous and testing commands:
   DANGEROUS!!! Factory set bad blocks will be lost. Use only
   to remove artificial bad blocks created with the "markbad" command.
 
   DANGEROUS!!! Factory set bad blocks will be lost. Use only
   to remove artificial bad blocks created with the "markbad" command.
 

-  "torture offset"
+  "torture offset [size]"

   Torture block to determine if it is still reliable.
   Enabled by the CONFIG_CMD_NAND_TORTURE configuration option.
   This command returns 0 if the block is still reliable, else 1.
   Torture block to determine if it is still reliable.
   Enabled by the CONFIG_CMD_NAND_TORTURE configuration option.
   This command returns 0 if the block is still reliable, else 1.


@@ -345,6 +318,10 @@ Miscellaneous and testing commands:
   automate actions following a nand->write() error. This would e.g. be required
   in order to program or update safely firmware to NAND, especially for the UBI
   part of such firmware.
   automate actions following a nand->write() error. This would e.g. be required
   in order to program or update safely firmware to NAND, especially for the UBI
   part of such firmware.

+  Optionally, a second parameter size can be given to test multiple blocks with
+  one call. If size is not a multiple of the NAND's erase size, then the block
+  that contains offset + size will be tested in full. If used with size, this
+  command returns 0 if all tested blocks have been found reliable, else 1.

 
 
 NAND locking command (for chips with active LOCKPRE pin)
 
 
 NAND locking command (for chips with active LOCKPRE pin)