usb: sunxi: sun50i: enable OHCI0 clock when OHCI1 is in use

[u-boot] / drivers / i2c / Kconfig

diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig
index 4e9afc120a3ff4789afa428387a9a6f2c1fcddf0..5eceab9ea81497753adbd888c938e0c5975a9063 100644 (file)
--- a/drivers/i2c/Kconfig
+++ b/drivers/i2c/Kconfig
@@ -114,6 +114,15 @@ config SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED
          enable status register. This config option can be enabled in such
          cases.
 
          enable status register. This config option can be enabled in such
          cases.
 

+config SYS_I2C_ASPEED
+       bool "Aspeed I2C Controller"
+       depends on DM_I2C && ARCH_ASPEED
+       help
+         Say yes here to select Aspeed I2C Host Controller. The driver
+         supports AST2500 and AST2400 controllers, but is very limited.
+         Only single master mode is supported and only byte-by-byte
+         synchronous reads and writes are supported, no Pool Buffers or DMA.
+

 config SYS_I2C_INTEL
        bool "Intel I2C/SMBUS driver"
        depends on DM_I2C
 config SYS_I2C_INTEL
        bool "Intel I2C/SMBUS driver"
        depends on DM_I2C


@@ -125,18 +134,223 @@ config SYS_I2C_INTEL
 
 config SYS_I2C_IMX_LPI2C
        bool "NXP i.MX LPI2C driver"
 
 config SYS_I2C_IMX_LPI2C
        bool "NXP i.MX LPI2C driver"

-       depends on ARCH_MX7ULP

        help
          Add support for the NXP i.MX LPI2C driver.
 
        help
          Add support for the NXP i.MX LPI2C driver.
 

+config SYS_I2C_MESON
+       bool "Amlogic Meson I2C driver"
+       depends on DM_I2C && ARCH_MESON
+       help
+         Add support for the I2C controller available in Amlogic Meson
+         SoCs. The controller supports programmable bus speed including
+         standard (100kbits/s) and fast (400kbit/s) speed and allows the
+         software to define a flexible format of the bit streams. It has an
+         internal buffer holding up to 8 bytes for transfers and supports
+         both 7-bit and 10-bit addresses.
+

 config SYS_I2C_MXC
 config SYS_I2C_MXC

-       bool "NXP i.MX I2C driver"
-       depends on MX6
+       bool "NXP MXC I2C driver"

        help
        help

-         Add support for the NXP i.MX I2C driver. This supports upto for bus
+         Add support for the NXP I2C driver. This supports upto for bus

          channels and operating on standard mode upto 100 kbits/s and fast
          mode upto 400 kbits/s.
 
          channels and operating on standard mode upto 100 kbits/s and fast
          mode upto 400 kbits/s.
 

+if SYS_I2C_MXC
+config SYS_I2C_MXC_I2C1
+       bool "NXP MXC I2C1"
+       help
+        Add support for NXP MXC I2C Controller 1.
+        Required for SoCs which have I2C MXC controller 1 eg LS1088A, LS2080A
+
+config SYS_I2C_MXC_I2C2
+       bool "NXP MXC I2C2"
+       help
+        Add support for NXP MXC I2C Controller 2.
+        Required for SoCs which have I2C MXC controller 2 eg LS1088A, LS2080A
+
+config SYS_I2C_MXC_I2C3
+       bool "NXP MXC I2C3"
+       help
+        Add support for NXP MXC I2C Controller 3.
+        Required for SoCs which have I2C MXC controller 3 eg LS1088A, LS2080A
+
+config SYS_I2C_MXC_I2C4
+       bool "NXP MXC I2C4"
+       help
+        Add support for NXP MXC I2C Controller 4.
+        Required for SoCs which have I2C MXC controller 4 eg LS1088A, LS2080A
+
+config SYS_I2C_MXC_I2C5
+       bool "NXP MXC I2C5"
+       help
+        Add support for NXP MXC I2C Controller 5.
+        Required for SoCs which have I2C MXC controller 5 eg LX2160A
+
+config SYS_I2C_MXC_I2C6
+       bool "NXP MXC I2C6"
+       help
+        Add support for NXP MXC I2C Controller 6.
+        Required for SoCs which have I2C MXC controller 6 eg LX2160A
+
+config SYS_I2C_MXC_I2C7
+       bool "NXP MXC I2C7"
+       help
+        Add support for NXP MXC I2C Controller 7.
+        Required for SoCs which have I2C MXC controller 7 eg LX2160A
+
+config SYS_I2C_MXC_I2C8
+       bool "NXP MXC I2C8"
+       help
+        Add support for NXP MXC I2C Controller 8.
+        Required for SoCs which have I2C MXC controller 8 eg LX2160A
+endif
+
+if SYS_I2C_MXC_I2C1
+config SYS_MXC_I2C1_SPEED
+       int "I2C Channel 1 speed"
+       default 40000000 if TARGET_LS2080A_SIMU || TARGET_LS2080A_EMU
+       default 100000
+       help
+        MXC I2C Channel 1 speed
+
+config SYS_MXC_I2C1_SLAVE
+       int "I2C1 Slave"
+       default 0
+       help
+        MXC I2C1 Slave
+endif
+
+if SYS_I2C_MXC_I2C2
+config SYS_MXC_I2C2_SPEED
+       int "I2C Channel 2 speed"
+       default 40000000 if TARGET_LS2080A_SIMU || TARGET_LS2080A_EMU
+       default 100000
+       help
+        MXC I2C Channel 2 speed
+
+config SYS_MXC_I2C2_SLAVE
+       int "I2C2 Slave"
+       default 0
+       help
+        MXC I2C2 Slave
+endif
+
+if SYS_I2C_MXC_I2C3
+config SYS_MXC_I2C3_SPEED
+       int "I2C Channel 3 speed"
+       default 100000
+       help
+        MXC I2C Channel 3 speed
+
+config SYS_MXC_I2C3_SLAVE
+       int "I2C3 Slave"
+       default 0
+       help
+        MXC I2C3 Slave
+endif
+
+if SYS_I2C_MXC_I2C4
+config SYS_MXC_I2C4_SPEED
+       int "I2C Channel 4 speed"
+       default 100000
+       help
+        MXC I2C Channel 4 speed
+
+config SYS_MXC_I2C4_SLAVE
+       int "I2C4 Slave"
+       default 0
+       help
+        MXC I2C4 Slave
+endif
+
+if SYS_I2C_MXC_I2C5
+config SYS_MXC_I2C5_SPEED
+       int "I2C Channel 5 speed"
+       default 100000
+       help
+        MXC I2C Channel 5 speed
+
+config SYS_MXC_I2C5_SLAVE
+       int "I2C5 Slave"
+       default 0
+       help
+        MXC I2C5 Slave
+endif
+
+if SYS_I2C_MXC_I2C6
+config SYS_MXC_I2C6_SPEED
+       int "I2C Channel 6 speed"
+       default 100000
+       help
+        MXC I2C Channel 6 speed
+
+config SYS_MXC_I2C6_SLAVE
+       int "I2C6 Slave"
+       default 0
+       help
+        MXC I2C6 Slave
+endif
+
+if SYS_I2C_MXC_I2C7
+config SYS_MXC_I2C7_SPEED
+       int "I2C Channel 7 speed"
+       default 100000
+       help
+        MXC I2C Channel 7 speed
+
+config SYS_MXC_I2C7_SLAVE
+       int "I2C7 Slave"
+       default 0
+       help
+        MXC I2C7 Slave
+endif
+
+if SYS_I2C_MXC_I2C8
+config SYS_MXC_I2C8_SPEED
+       int "I2C Channel 8 speed"
+       default 100000
+       help
+        MXC I2C Channel 8 speed
+
+config SYS_MXC_I2C8_SLAVE
+       int "I2C8 Slave"
+       default 0
+       help
+        MXC I2C8 Slave
+endif
+
+config SYS_I2C_OMAP24XX
+       bool "TI OMAP2+ I2C driver"
+       depends on ARCH_OMAP2PLUS
+       help
+         Add support for the OMAP2+ I2C driver.
+
+if SYS_I2C_OMAP24XX
+config SYS_OMAP24_I2C_SLAVE
+       int "I2C Slave addr channel 0"
+       default 1
+       help
+         OMAP24xx I2C Slave address channel 0
+
+config SYS_OMAP24_I2C_SPEED
+       int "I2C Slave channel 0 speed"
+       default 100000
+       help
+         OMAP24xx Slave speed channel 0
+endif
+
+config SYS_I2C_RCAR_I2C
+       bool "Renesas RCar I2C driver"
+       depends on (RCAR_GEN3 || RCAR_GEN2) && DM_I2C
+       help
+         Support for Renesas RCar I2C controller.
+
+config SYS_I2C_RCAR_IIC
+       bool "Renesas RCar Gen3 IIC driver"
+       depends on (RCAR_GEN3 || RCAR_GEN2) && DM_I2C
+       help
+         Support for Renesas RCar Gen3 IIC controller.
+

 config SYS_I2C_ROCKCHIP
        bool "Rockchip I2C driver"
        depends on DM_I2C
 config SYS_I2C_ROCKCHIP
        bool "Rockchip I2C driver"
        depends on DM_I2C


@@ -160,6 +374,26 @@ config SYS_I2C_S3C24X0
        help
          Support for Samsung I2C controller as Samsung SoCs.
 
        help
          Support for Samsung I2C controller as Samsung SoCs.
 

+config SYS_I2C_STM32F7
+       bool "STMicroelectronics STM32F7 I2C support"
+       depends on (STM32F7 || STM32H7 || ARCH_STM32MP) && DM_I2C
+       help
+         Enable this option to add support for STM32 I2C controller
+         introduced with STM32F7/H7 SoCs. This I2C controller supports :
+          _ Slave and master modes
+          _ Multimaster capability
+          _ Standard-mode (up to 100 kHz)
+          _ Fast-mode (up to 400 kHz)
+          _ Fast-mode Plus (up to 1 MHz)
+          _ 7-bit and 10-bit addressing mode
+          _ Multiple 7-bit slave addresses (2 addresses, 1 with configurable mask)
+          _ All 7-bit addresses acknowledge mode
+          _ General call
+          _ Programmable setup and hold times
+          _ Easy to use event management
+          _ Optional clock stretching
+          _ Software reset
+

 config SYS_I2C_UNIPHIER
        bool "UniPhier I2C driver"
        depends on ARCH_UNIPHIER && DM_I2C
 config SYS_I2C_UNIPHIER
        bool "UniPhier I2C driver"
        depends on ARCH_UNIPHIER && DM_I2C


@@ -193,6 +427,54 @@ config TEGRA186_BPMP_I2C
          by the BPMP, and can only be accessed by the main CPU via IPC
          requests to the BPMP. This driver covers the latter case.
 
          by the BPMP, and can only be accessed by the main CPU via IPC
          requests to the BPMP. This driver covers the latter case.
 

+config SYS_I2C_BUS_MAX
+       int "Max I2C busses"
+       depends on ARCH_KEYSTONE || ARCH_OMAP2PLUS || ARCH_SOCFPGA
+       default 2 if TI816X
+       default 3 if OMAP34XX || AM33XX || AM43XX || ARCH_KEYSTONE
+       default 4 if ARCH_SOCFPGA || OMAP44XX || TI814X
+       default 5 if OMAP54XX
+       help
+         Define the maximum number of available I2C buses.
+
+config SYS_I2C_ZYNQ
+       bool "Xilinx I2C driver"
+       depends on ARCH_ZYNQMP || ARCH_ZYNQ
+       help
+         Support for Xilinx I2C controller.
+
+config SYS_I2C_ZYNQ_SLAVE
+       hex "Set slave addr"
+       depends on SYS_I2C_ZYNQ
+       default 0
+       help
+         Set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr.
+
+config SYS_I2C_ZYNQ_SPEED
+       int "Set I2C speed"
+       depends on SYS_I2C_ZYNQ
+       default 100000
+       help
+         Set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting.
+
+config ZYNQ_I2C0
+       bool "Xilinx I2C0 controller"
+       depends on SYS_I2C_ZYNQ
+       help
+         Enable Xilinx I2C0 controller.
+
+config ZYNQ_I2C1
+       bool "Xilinx I2C1 controller"
+       depends on SYS_I2C_ZYNQ
+       help
+         Enable Xilinx I2C1 controller.
+
+config SYS_I2C_IHS
+        bool "gdsys IHS I2C driver"
+        depends on DM_I2C
+        help
+          Support for gdsys IHS I2C driver on FPGA bus.
+

 source "drivers/i2c/muxes/Kconfig"
 
 endmenu
 source "drivers/i2c/muxes/Kconfig"
 
 endmenu