ddr: altera: silence PHY calibration unless in debug mode

[u-boot] / drivers / mmc / Kconfig

diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
index c34ab219e88498c764ed5bae0e3adc024437add9..bc29611d783be4788777ef70e7ed14cbe1c8004b 100644 (file)
--- a/drivers/mmc/Kconfig
+++ b/drivers/mmc/Kconfig
@@ -10,6 +10,18 @@ config MMC
          If you want MMC/SD/SDIO support, you should say Y here and
          also to your specific host controller driver.
 
          If you want MMC/SD/SDIO support, you should say Y here and
          also to your specific host controller driver.
 

+config MMC_WRITE
+       bool "support for MMC/SD write operations"
+       depends on MMC
+       default y
+       help
+         Enable write access to MMC and SD Cards
+
+config MMC_BROKEN_CD
+       bool "Poll for broken card detection case"
+       help
+         If card  detection feature is broken, just poll to detect.
+

 config DM_MMC
        bool "Enable MMC controllers using Driver Model"
        depends on DM
 config DM_MMC
        bool "Enable MMC controllers using Driver Model"
        depends on DM


@@ -51,6 +63,59 @@ config MMC_QUIRKS
          are enabled by default, other may require additionnal flags or are
          enabled by the host driver.
 
          are enabled by default, other may require additionnal flags or are
          enabled by the host driver.
 

+config MMC_HW_PARTITIONING
+       bool "Support for HW partitioning command(eMMC)"
+       default y
+       help
+         This adds a command and an API to do hardware partitioning on eMMC
+         devices.
+
+config MMC_IO_VOLTAGE
+       bool "Support IO voltage configuration"
+       help
+         IO voltage configuration allows selecting the voltage level of the IO
+         lines (not the level of main supply). This is required for UHS
+         support. For eMMC this not mandatory, but not enabling this option may
+         prevent the driver of using the faster modes.
+
+config SPL_MMC_IO_VOLTAGE
+       bool "Support IO voltage configuration in SPL"
+       default n
+       help
+         IO voltage configuration allows selecting the voltage level of the IO
+         lines (not the level of main supply). This is required for UHS
+         support. For eMMC this not mandatory, but not enabling this option may
+         prevent the driver of using the faster modes.
+
+config MMC_UHS_SUPPORT
+       bool "enable UHS support"
+       depends on MMC_IO_VOLTAGE
+       help
+         The Ultra High Speed (UHS) bus is available on some SDHC and SDXC
+         cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus
+         frequency can go up to 208MHz (SDR104)
+
+config SPL_MMC_UHS_SUPPORT
+       bool "enable UHS support in SPL"
+       depends on SPL_MMC_IO_VOLTAGE
+       help
+         The Ultra High Speed (UHS) bus is available on some SDHC and SDXC
+         cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus
+         frequency can go up to 208MHz (SDR104)
+
+config MMC_HS200_SUPPORT
+       bool "enable HS200 support"
+       help
+         The HS200 mode is support by some eMMC. The bus frequency is up to
+         200MHz. This mode requires tuning the IO.
+
+
+config SPL_MMC_HS200_SUPPORT
+       bool "enable HS200 support in SPL"
+       help
+         The HS200 mode is support by some eMMC. The bus frequency is up to
+         200MHz. This mode requires tuning the IO.
+

 config MMC_VERBOSE
        bool "Output more information about the MMC"
        default y
 config MMC_VERBOSE
        bool "Output more information about the MMC"
        default y