powerpc: MPC8610: Remove macro CONFIG_MPC8610

[u-boot] / dts / Kconfig

diff --git a/dts/Kconfig b/dts/Kconfig
index ca5bd6fb46626eafb7b0f15d023d243b79783f93..4b7d8b15cc04d7f3a81ab7edf50268901ee4cf8c 100644 (file)
--- a/dts/Kconfig
+++ b/dts/Kconfig
@@ -1,9 +1,6 @@
 #
 # Device Tree Control
 #
 #
 # Device Tree Control
 #

-# TODO:
-#   This feature is not currently supported for SPL,
-#    but this restriction should be removed in the future.

 
 config SUPPORT_OF_CONTROL
        bool
 
 config SUPPORT_OF_CONTROL
        bool


@@ -17,6 +14,14 @@ config OF_CONTROL
          This feature provides for run-time configuration of U-Boot
          via a flattened device tree.
 
          This feature provides for run-time configuration of U-Boot
          via a flattened device tree.
 

+config SPL_OF_CONTROL
+       bool "Enable run-time configuration via Device Tree in SPL"
+       depends on SPL && OF_CONTROL
+       help
+         Some boards use device tree in U-Boot but only have 4KB of SRAM
+         which is not enough to support device tree. Enable this option to
+         allow such boards to be supported by U-Boot SPL.
+

 choice
        prompt "Provider of DTB for DT control"
        depends on OF_CONTROL
 choice
        prompt "Provider of DTB for DT control"
        depends on OF_CONTROL


@@ -32,7 +37,9 @@ config OF_EMBED
        bool "Embedded DTB for DT control"
        help
          If this option is enabled, the device tree will be picked up and
        bool "Embedded DTB for DT control"
        help
          If this option is enabled, the device tree will be picked up and

-         built into the U-Boot image.
+         built into the U-Boot image. This is suitable for local debugging
+         and development only and is not recommended for production devices.
+         Boards in the mainline U-Boot tree should not use it.

 
 config OF_HOSTFILE
        bool "Host filed DTB for DT control"
 
 config OF_HOSTFILE
        bool "Host filed DTB for DT control"


@@ -46,9 +53,57 @@ endchoice
 
 config DEFAULT_DEVICE_TREE
        string "Default Device Tree for DT control"
 
 config DEFAULT_DEVICE_TREE
        string "Default Device Tree for DT control"

+       depends on OF_CONTROL

        help
          This option specifies the default Device Tree used for DT control.
          It can be overridden from the command line:
          $ make DEVICE_TREE=<device-tree-name>
 
        help
          This option specifies the default Device Tree used for DT control.
          It can be overridden from the command line:
          $ make DEVICE_TREE=<device-tree-name>
 

+config OF_LIST
+       string "List of device tree files to include for DT control"
+       depends on SPL_LOAD_FIT
+       default DEFAULT_DEVICE_TREE
+       help
+         This option specifies a list of device tree files to use for DT
+         control. These will be packaged into a FIT. At run-time, SPL will
+         select the correct DT to use by examining the hardware (e.g.
+         reading a board ID value). This is a list of device tree files
+         (without the directory or .dtb suffix) separated by <space>.
+
+config OF_SPL_REMOVE_PROPS
+       string "List of device tree properties to drop for SPL"
+       depends on SPL_OF_CONTROL
+       default "interrupt-parent" if SPL_PINCTRL_FULL && SPL_CLK
+       default "clocks clock-names interrupt-parent" if SPL_PINCTRL_FULL
+       default "pinctrl-0 pinctrl-names interrupt-parent" if SPL_CLK
+       default "pinctrl-0 pinctrl-names clocks clock-names interrupt-parent"
+       help
+         Since SPL normally runs in a reduced memory space, the device tree
+         is cut down to only what is needed to load and start U-Boot. Only
+         nodes marked with the property "u-boot,dm-pre-reloc" will be
+         included. In addition, some properties are not used by U-Boot and
+         can be discarded. This option defines the list of properties to
+         discard.
+
+config SPL_OF_PLATDATA
+       bool "Generate platform data for use in SPL"
+       depends on SPL_OF_CONTROL
+       help
+         For very constrained SPL environments the overhead of decoding
+         device tree nodes and converting their contents into platform data
+         is too large. This overhead includes libfdt code as well as the
+         device tree contents itself. The latter is fairly compact, but the
+         former can add 3KB or more to a Thumb 2 Image.
+
+         This option enables generation of platform data from the device
+         tree as C code. This code creates devices using U_BOOT_DEVICE()
+         declarations. The benefit is that it allows driver code to access
+         the platform data directly in C structures, avoidin the libfdt
+         overhead.
+
+         This option works by generating C structure declarations for each
+         compatible string, then adding platform data and U_BOOT_DEVICE
+         declarations for each node. See README.platdata for more
+         information.
+

 endmenu
 endmenu