+/*** NETVIA *******************************************************/
+
+/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */
+#if ( defined CONFIG_SVM_SC8xx )
+# ifndef CONFIG_FEC_ENET
+
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+
+ /* Bits in parallel I/O port registers that have to be set/cleared
+ * * * * to configure the pins for SCC2 use.
+ * * * */
+#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
+#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
+#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */
+#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
+
+#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
+
+#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
+#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ * * * */
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00003700)
+
+# else /* Use FEC for Fast Ethernet */
+
+#undef SCC_ENET
+#define FEC_ENET
+
+#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
+#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
+#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
+#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
+#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
+#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
+#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
+#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
+#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
+#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
+#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
+#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
+#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
+
+#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
+
+# endif /* CONFIG_FEC_ENET */
+#endif /* CONFIG_SVM_SC8xx */
+
+
+#if defined(CONFIG_NETVIA)
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
+#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
+#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
+#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
+
+#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1
+# define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */
+#elif CONFIG_NETVIA_VERSION >= 2
+# define PC_ENET_PDN ((ushort)0x0008) /* PC 12 */
+#endif
+
+#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */
+
+#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
+#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK ((uint)0x0000ff00)
+#define SICR_ENET_CLKRT ((uint)0x00002f00)
+
+#endif /* CONFIG_NETVIA */
+
+/*** QS850/QS823 ***************************************************/
+
+#if defined(CONFIG_QS850) || defined(CONFIG_QS823)
+#undef FEC_ENET /* Don't use FEC for EThernet */
+
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+
+#define PA_ENET_RXD ((ushort)0x0004) /* RXD on PA13 (Pin D9) */
+#define PA_ENET_TXD ((ushort)0x0008) /* TXD on PA12 (Pin D7) */
+#define PC_ENET_RENA ((ushort)0x0080) /* RENA on PC8 (Pin D12) */
+#define PC_ENET_CLSN ((ushort)0x0040) /* CLSN on PC9 (Pin C12) */
+#define PA_ENET_TCLK ((ushort)0x0200) /* TCLK on PA6 (Pin D8) */
+#define PA_ENET_RCLK ((ushort)0x0800) /* RCLK on PA4 (Pin D10) */
+#define PB_ENET_TENA ((uint)0x00002000) /* TENA on PB18 (Pin D11) */
+#define PC_ENET_LBK ((ushort)0x0010) /* Loopback control on PC11 (Pin B14) */
+#define PC_ENET_LI ((ushort)0x0020) /* Link Integrity control PC10 (A15) */
+#define PC_ENET_SQE ((ushort)0x0100) /* SQE Disable control PC7 (B15) */
+
+/* SCC2 TXCLK from CLK2
+ * SCC2 RXCLK from CLK4
+ * SCC2 Connected to NMSI */
+#define SICR_ENET_MASK ((uint)0x00007F00)
+#define SICR_ENET_CLKRT ((uint)0x00003D00)
+
+#endif /* CONFIG_QS850/QS823 */
+
+/*** QS860T ***************************************************/
+
+#ifdef CONFIG_QS860T
+#ifdef CONFIG_FEC_ENET
+#define FEC_ENET /* use FEC for EThernet */
+#endif /* CONFIG_FEC_ETHERNET */
+
+/* This ENET stuff is for GTH 10 Mbit ( SCC ) */
+#define PROFF_ENET PROFF_SCC1
+#define CPM_CR_ENET CPM_CR_CH_SCC1
+#define SCC_ENET 0
+
+#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */
+#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */
+#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */
+#define PA_ENET_RCLK ((ushort)0x0200) /* PA6 */
+#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */
+#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */
+#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */
+
+#define SICR_ENET_MASK ((uint)0x000000ff)
+/* RCLK PA4 -->CLK4, TCLK PA6 -->CLK2 */
+#define SICR_ENET_CLKRT ((uint)0x0000003D)
+
+#endif /* CONFIG_QS860T */
+