+#define PHYS_FLASH_SIZE 0x01000000 /* 16MB */
+#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+
+#define CFG_MONITOR_LEN 0x00100000
+#define CFG_ENV_IS_IN_FLASH (1)
+
+/*
+ * Move up the U-Boot & monitor area if more flash is fitted.
+ * If this U-Boot is to be run on Integrators with varying flash sizes,
+ * drivers/cfi_flash.c::flash_init() can read the Integrator CP_FLASHPROG
+ * register and dynamically assign CFG_ENV_ADDR & CFG_MONITOR_BASE
+ * - CFG_MONITOR_BASE is set to indicate that the environment is not
+ * embedded in the boot monitor(s) area
+ */
+#if ( PHYS_FLASH_SIZE == 0x04000000 )
+
+#define CFG_ENV_ADDR 0x27F00000
+#define CFG_MONITOR_BASE 0x27F40000
+
+#elif (PHYS_FLASH_SIZE == 0x02000000 )
+
+#define CFG_ENV_ADDR 0x25F00000
+#define CFG_MONITOR_BASE 0x25F40000
+
+#else
+
+#define CFG_ENV_ADDR 0x24F00000
+#define CFG_MONITOR_BASE 0x27F40000
+
+#endif
+
+#define CFG_ENV_SECT_SIZE 0x40000 /* 256KB */
+#define CFG_ENV_SIZE 8192 /* 8KB */
+/*-----------------------------------------------------------------------
+ * CP control registers
+ */
+#define CPCR_BASE 0xCB000000 /* CP Registers*/
+#define OS_FLASHPROG 0x00000004 /* Flash register*/
+#define CPMASK_EXTRABANK 0x8
+#define CPMASK_FLASHSIZE 0x4
+#define CPMASK_FLWREN 0x2
+#define CPMASK_FLVPPEN 0x1
+
+/*
+ * The ARM boot monitor initializes the board.
+ * However, the default U-Boot code also performs the initialization.
+ * If desired, this can be prevented by defining SKIP_LOWLEVEL_INIT
+ * - see documentation supplied with board for details of how to choose the
+ * image to run at reset/power up
+ * e.g. whether the ARM Boot Monitor runs before U-Boot
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+ */
+
+/*
+ * The ARM boot monitor does not relocate U-Boot.
+ * However, the default U-Boot code performs the relocation check,
+ * and may relocate the code if the memory map is changed.
+ * If necessary this can be prevented by defining SKIP_RELOCATE_UBOOT
+
+#define SKIP_CONFIG_RELOCATE_UBOOT
+
+ */
+/*-----------------------------------------------------------------------
+ * There are various dependencies on the core module (CM) fitted
+ * Users should refer to their CM user guide
+ * - when porting adjust u-boot/Makefile accordingly
+ * to define the necessary CONFIG_ s for the CM involved
+ * see e.g. cp_926ejs_config
+ */
+
+#include "armcoremodule.h"
+
+/*
+ * If CONFIG_SKIP_LOWLEVEL_INIT is not defined &
+ * the core module has a CM_INIT register
+ * then the U-Boot initialisation code will
+ * e.g. ARM Boot Monitor or pre-loader is repeated once
+ * (to re-initialise any existing CM_INIT settings to safe values).
+ *
+ * This is usually not the desired behaviour since the platform
+ * will either reboot into the ARM monitor (or pre-loader)
+ * or continuously cycle thru it without U-Boot running,
+ * depending upon the setting of Integrator/CP switch S2-4.
+ *
+ * However it may be needed if Integrator/CP switch S2-1
+ * is set OFF to boot direct into U-Boot.
+ * In that case comment out the line below.
+#undef CONFIG_CM_INIT
+ */
+
+#endif /* __CONFIG_H */