- OR_GPCM_TRLX | OR_GPCM_EAD)
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/* Pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#undef CONFIG_PCI /* No PCI */
-
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "FSL UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_RAMBOOT */
-#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
-#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_RAMBOOT */
-
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 200000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_I2C_MULTI_BUS 1
-#define CONFIG_I2C_MUX 1
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0, 1, 2, 3} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS)
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_PIGGY_BASE
-#endif
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#endif
-
-#if defined(CFG_RAMBOOT)
-#undef CONFIG_CMD_SAVEENV
-#undef CONFIG_CMD_LOADS
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2 HID2_HBE