+commit c3147c1762f8caf99649051116a2411bdf887c10
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sun Jun 14 20:31:36 2009 +0200
+
+ Revert "SMC911x driver fixed for NFS boot"
+
+ This reverts commit ca9c8a1e10fac01e6a1129f82a7ce18bd818fa43,
+ which causes compile warnings ("large integer implicitly truncated
+ to unsigned type") on all systems that use this driver. The warning
+ results from passing long constants (TX_CFG, RX_CFG) into
+ smc911x_set_mac_csr() which is declared to accept "unsigned
+ character" arguments only.
+
+ Being close to a release, with nobody available to actually test the
+ code or the suggested fixes, it seems better to revert the patch.
+
+commit e7563aff174f77aa61dab1ef5d9b47bebaa43702
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Jun 11 23:42:35 2009 -0500
+
+ fsl-ddr: Fix handling of >4G of memory when !CONFIG_PHYS_64BIT
+
+ The ddr code computes most things as 64-bit quantities and had some places
+ in the middle that it was using phy_addr_t and phys_size_t.
+
+ Instead we use unsigned long long through out and only at the last stage of
+ setting the LAWs and reporting the amount of memory to the board code do we
+ truncate down to what we can cover via phys_size_t.
+
+ This has the added benefit that the DDR controller itself is always setup
+ the same way regardless of how much memory we have. Its only the LAW
+ setup that limits what is visible to the system.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit d4b130dc80761b430dc5b410159cd158fca1a348
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Thu Jun 11 23:40:34 2009 -0500
+
+ 85xx: Use print_size to report amount of memory not mapped by TLBs
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 6e2aebc33fa740c068fe28d40eaf0319b7c7287e
+Author: Haiying Wang <Haiying.Wang@freescale.com>
+Date: Wed May 20 12:30:42 2009 -0400
+
+ 85xx: Add README for MPC8569MDS
+
+ Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit b2aab386e957ba684d4f2a466bfaa91770e5058a
+Author: Haiying Wang <Haiying.Wang@freescale.com>
+Date: Wed May 20 12:30:33 2009 -0400
+
+ 85xx: Add UART1 support for MPC8569MDS
+
+ MPC8569 UART1 signals are muxed with PortF bit[9-12], we need to define
+ those pins before using UART1.
+
+ Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 399b53cbab0b377ac4c5c16c19c6e41b68a9c719
+Author: Haiying Wang <Haiying.Wang@freescale.com>
+Date: Wed May 20 12:30:32 2009 -0400
+
+ 85xx: Add PIB support at CS4/CS5 for MPC8569MDS
+
+ Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+ Signed-off-by: Yu Liu <Yu.Liu@freescale.com>
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit fb27949059f1bc84381a6216a819090f0cdbaa70
+Author: Haiying Wang <Haiying.Wang@freescale.com>
+Date: Thu Jun 4 16:12:39 2009 -0400
+
+ 85xx: Fix some settings for MPC8569MDS board
+
+ - Increase the size of malloc to 512KB because MPC8569MDS needs more memory for
+ malloc to support up to eight Ethernet interfaces.
+ - Move Environment address out of uboot thus the saved environment variables
+ will not be erased after u-boot is re-programmed.
+
+ Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit c7f60fd29f2d638d080cdf1a49ad985b85f9429d
+Author: Haiying Wang <Haiying.Wang@freescale.com>
+Date: Wed May 20 12:30:30 2009 -0400
+
+ 85xx: Fix MURAM size for MPC8569
+
+ MPC8569 has 128K bytes MURAM.
+
+ Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit a53c997dd7fc858f2a27f5a47b200567b9343ae5
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Fri May 22 20:23:51 2009 +0200
+
+ at91/cpu.c: add missing Copyright & GPL header
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit aa446a591aca46ef2b53cc6598ea8091feb45444
+Author: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
+Date: Sun Jun 7 21:45:16 2009 +0900
+
+ apollon: Fix a OBJCFLAGS typo
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
+
+commit 580611cb0932143fc2d7a735cfa9ce1ef34d6002
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Jun 10 00:19:28 2009 +0200
+
+ Prepare 2009.06-rc3
+
+ Update CHANGELOG
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 3a76ab5c166d5956885f803ce975e7151cc0ca0e
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Jun 10 00:15:11 2009 +0200
+
+ rmu board: fix error: 'CONFIG_ENV_SECT_SIZE' undeclared
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 165f9859b64ff59f0cfae3cc70a7e7ded7aaa4a7
+Author: Daniel Mack <daniel@caiaq.de>
+Date: Thu Jun 4 19:44:12 2009 +0200
+
+ ubifs: fix small error path mismatch
+
+ In do_readpage(), don't free 'dn' if its allocation failed.
+
+ Signed-off-by: Daniel Mack <daniel@caiaq.de>
+
+commit de7cf709ebd3c01fbd094e8853dabb410c0370a1
+Author: Wolfgang Denk <wd@denx.de>
+Date: Thu Jun 4 00:31:07 2009 +0200
+
+ EP88x: fix broken linker script
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+ Tested-by: Mikhail Zaturenskiy <mzaturenskiy@shoppertrak.com>
+
+commit 7a2063bd80d3b58b2dd5d5e58f4411f8d250576c
+Author: Wolfgang Denk <wd@denx.de>
+Date: Fri May 15 00:16:02 2009 +0200
+
+ TQM85xx: minor config file cleanup
+
+ Remove "saveenv" from "update" definition: the environment is outside
+ the U-Boot image on TQM85xx and therefor not affected by updates.
+
+ Also "beautify" code a bit (vertical alignment).
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit c0296b1801fc9426d772fa75fe58458db605dfee
+Author: Wolfgang Denk <wd@denx.de>
+Date: Fri May 15 00:16:01 2009 +0200
+
+ TQM85xx: adapt for new flash types
+
+ Old TQM85xx boards had 'M' type Spansion Flashes from the S29GLxxxM
+ series while new boards have 'N' type Flashes from the S29GLxxxN
+ series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB.
+
+ We now change the configuration to the new flash types for all
+ boards; this also works on old boards - we just waste two flash
+ sectors for the environment which could be smaller there.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 6735104924f06340071a6914a9ee3345607fc102
+Author: Dave Liu <daveliu@freescale.com>
+Date: Mon May 18 17:49:23 2009 +0800
+
+ 85xx: Fix the wrong SYS_CLK_IN for 8569MDS
+
+ The SYS_CLK_IN of MPC8569MDS is 66.66MHz,
+ The DDR_CLK_IN is same with SYS_CLK_IN in 8569 processor.
+ so, change the SYS_CLK_IN from 66MHz to 66.66MHz.
+
+ Signed-off-by: Dave Liu <daveliu@freescale.com>
+
+commit 16e7559c08b6f29db4596d795b92914c01e6a1b3
+Author: Dave Liu <daveliu@freescale.com>
+Date: Fri May 15 10:27:44 2009 +0800
+
+ 85xx: Fix the wrong BCSR address of 8569MDS
+
+ The BCSR17[7] = 1 will unlock the write protect of FLASH.
+ The WP# pin only controls the write protect of top/bottom sector,
+ That is why we can save env, but we can't write the first sector
+ before the patch.
+
+ Signed-off-by: Dave Liu <daveliu@freescale.com>
+
+commit 90d13b8ac3d515349626d7c8a3dc34ef38c43fa6
+Author: Fredrik Arnerup <fredrik.arnerup@edgeware.tv>
+Date: Tue Jun 2 16:27:10 2009 -0500
+
+ 85xx: bugfix for reading maximum TLB size on mpc85xx
+
+ The MAXSIZE field in the TLB1CFG register is 4 bits, not 8 bits.
+ This made setup_ddr_tlbs() try to set up a TLB larger than the e500 maximum
+ (256 MB)
+ which made u-boot hang in board_init_f() when trying to create a new stack
+ in RAM.
+ I have an mpc8540 with one 1GB dimm.
+
+ Signed-off-by: Fredrik Arnerup <fredrik.arnerup@edgeware.tv>
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+ Acked-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 1b5291dddf5f16c7ae10e3cb165882fa96038b26
+Author: Dave Liu <daveliu@freescale.com>
+Date: Fri Mar 27 14:32:43 2009 +0800
+
+ 85xx: Fix the clock adjust of mpc8569mds board
+
+ Currently the clk_adj is 6 (3/4 cycle), The settings will cause
+ the DDR controller hang at the data init. Change the clk_adj
+ from 6 to 4 (1/2 cycle), make the memory system stable.
+
+ Signed-off-by: Dave Liu <daveliu@freescale.com>
+
+commit faa14babd7466dfade358f9cac128ae246b9bf1b
+Author: RONETIX - Ilko Iliev <iliev@ronetix.at>
+Date: Fri Jun 5 16:54:31 2009 +0200
+
+ at91: fix a USB problem for AT91SAM9261
+
+ This patch corrects the missing PLLB initialization in usb_cpu_init()
+ for AT91SAM9261.
+ Because of the missing PLLB initialization, the USB support for all
+ AT91SAM9261 based boards will work only if the PLLB is configured by a
+ precedent bootloader.
+
+ Signed-off-by: Ilko Iliev <iliev@ronetix.at>
+ Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Remy Bohmer <linux@bohmer.net>
+
+commit 0c24dec550ddb7d86b8bfdd8645b18479f73e6e2
+Author: Felix Radensky <felix@embedded-sol.com>
+Date: Sun May 31 20:44:15 2009 +0300
+
+ ppc4xx/net: Fix MDIO clock setup
+
+ This patch fixes MDIO clock setup in case when OPB frequency is 100MHz.
+ Current code assumes that the value of sysinfo.freqOPB is 100000000
+ when OPB frequency is 100MHz. In reality it is 100000001. As a result
+ MDIO clock is set to incorrect value, larger than 2.5MHz, thus violating
+ the standard. This in not a problem on boards equipped with Marvell PHYs
+ (e.g. Canyonlands), since those PHYs support MDIO clocks up to 8.3MHz,
+ but can be a problem for other PHYs (e.g. Realtek ones).
+
+ Signed-off-by: Felix Radensky <felix@embedded-sol.com>
+ Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
+
+commit d65e34d12514de2bbe3b8f519761d641c081bad0
+Author: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
+Date: Wed Feb 25 14:27:29 2009 +0900
+
+ rtl8169: fix PCI system memory address
+
+ When PCI device use system memory, some PCI host controller should be
+ set physical memory address.
+
+ Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
+ Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
+
+commit ca9c8a1e10fac01e6a1129f82a7ce18bd818fa43
+Author: Manikandan Pillai <mani.pillai@ti.com>
+Date: Wed Apr 8 09:14:35 2009 +0530
+
+ SMC911x driver fixed for NFS boot
+
+ eth_halt() function in the smc911x drivers used to call the
+ smc911x_reset() function. eth_halt() used to be called after
+ tftp transfers. This used to put the ethernet chip in reset
+ while the linux boots up resulting in the ethernet driver
+ not coming up. NFS boot used to fail as a result.
+
+ This patch calls smc911x_shutdown() instead of smc911x_reset().
+ Some comments received has also been fixed.
+
+ Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>
+ Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
+
+commit e5a3bc2401a23f1890611f020f57f94824a534db
+Author: Remy Bohmer <linux@bohmer.net>
+Date: Sun May 3 12:11:40 2009 +0200
+
+ Add config option for disabling DM9000-SROM support.
+
+ Some boards do not have SROM support for the DM9000 network adapter.
+ Instead of listing these board names in the driver code, make this
+ option configurable from the board config file.
+
+ It also removes a build warning for the at91sam9261ek board:
+ 'dm9000x.c:545: warning: 'read_srom_word' defined but not used'
+
+ And it repaires the trizepsiv board build which was broken around the
+ same routines
+
+ Signed-off-by: Remy Bohmer <linux@bohmer.net>
+ Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
+
+commit 3c9b1ee17e19bd6d80344678d41a85e52b0be713
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Fri Jun 5 14:11:33 2009 -0500
+
+ mpc83xx: don't set SICRH_TSOBI1 to RMII/RTBI operation
+
+ In GMII mode (which operates at 3.3V) both SICRH TSEC1/2 output buffer
+ impedance bits should be clear, i.e., SICRH[TSIOB1] = 0 and SICRH[TSIOB2] = 0.
+ SICRH[TSIOB1] was erroneously being set high.
+
+ U-Boot always operated this PHY interface in GMII mode. It is assumed this
+ was missed in the clean up by the original board porters, and copied along
+ to the TQM and sbc boards.
+
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
+ Acked-by: Ira Snyder <iws@ovro.caltech.edu>
+ Reviewed-by: David Hawkins <dwh@ovro.caltech.edu>
+ Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
+ CC: Dave Liu <DaveLiu@freescale.com>
+
+commit 2c0234fa79122a5aa77c4e17c33eb2fe184b61a7
+Author: Daniel Mack <daniel@caiaq.de>
+Date: Wed Apr 8 13:23:37 2009 +0200
+
+ smc911x: write back the manually set MAC address
+
+ If the MAX address is given by the environment, write it back to the
+ hardware.
+
+ Signed-off-by: Daniel Mack <daniel@caiaq.de>
+ Cc: Sascha Hauer <s.hauer@pengutronix.de>
+ Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
+
+commit dfcd7f21607fd847236b04bb1a8d59a7c10ab99c
+Author: Wolfgang Denk <wd@denx.de>
+Date: Fri May 15 00:16:03 2009 +0200
+
+ Redundant Environment: protect full sector size
+
+ Several boards used different ways to specify the size of the
+ protected area when enabling flash write protection for the sectors
+ holding the environment variables: some used CONFIG_ENV_SIZE and
+ CONFIG_ENV_SIZE_REDUND, some used CONFIG_ENV_SECT_SIZE, and some even
+ a mix of both for the "normal" and the "redundant" areas.
+
+ Normally, this makes no difference at all. However, things are
+ different when you have to deal with boards that can come with
+ different types of flash chips, which may have different sector
+ sizes.
+
+ Here we may have to chose CONFIG_ENV_SECT_SIZE such that it fits the
+ biggest sector size, which may include several sectors on boards using
+ the smaller sector flash types. In such a case, using CONFIG_ENV_SIZE
+ or CONFIG_ENV_SIZE_REDUND to enable the protection may lead to the
+ case that only the first of these sectors get protected, while the
+ following ones aren't.
+
+ This is no real problem, but it can be confusing for the user -
+ especially on boards that use CONFIG_ENV_SECT_SIZE to protect the
+ "normal" areas, while using CONFIG_ENV_SIZE_REDUND for the
+ "redundant" area.
+
+ To avoid such inconsistencies, I changed all sucn boards that I found
+ to consistently use CONFIG_ENV_SECT_SIZE for protection. This should
+ not cause any functional changes to the code.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+ Cc: Paul Ruhland
+ Cc: Pantelis Antoniou <panto@intracom.gr>
+ Cc: Stefan Roese <sr@denx.de>
+ Cc: Gary Jennejohn <garyj@denx.de>
+ Cc: Dave Ellis <DGE@sixnetio.com>
+ Acked-by: Stefan Roese <sr@denx.de>
+
+commit b81830f6e3b3e6ed114d071eb107965e49fa9b5a
+Author: Ilya Yanok <yanok@emcraft.com>
+Date: Thu May 14 14:03:09 2009 +0400
+
+ mmc: it's safe to ignore mmc_send_if_cond() return value
+
+ Return value of mmc_send_if_cond() can be safely ignored (as it is
+ done in Linux). This makes older cards work with MXC MCI controller.
+
+ Signed-off-by: Ilya Yanok <yanok@emcraft.com>
+
+commit dba6fcf6517faa5dda7df8109febe03c9c72a6f5
+Author: Stefan Roese <sr@denx.de>
+Date: Mon May 11 15:54:13 2009 +0200
+
+ cfi_mtd: Fix bug in last sector detection
+
+ This patch now enabled this cfi-mtd wrapper to correctly detect and
+ erase the last sector in an NOR FLASH device.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 4e3d89ba948eef801ffd46ef862cdede5b3f8320
+Author: Yauhen Kharuzhy <jekhor@gmail.com>
+Date: Thu May 7 00:43:30 2009 +0300
+
+ mmc: Fix decoding of SCR & function switch data on little-endian machines
+
+ SCR & switch data are read from card as big-endian words and should be
+ converted to CPU byte order.
+
+ Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit f33cb34b3971dabe3720d577b0e1b8601c09fe17
+Author: Yauhen Kharuzhy <jekhor@gmail.com>
+Date: Thu May 7 13:08:53 2009 +0300
+
+ mmc: Remove return from mmc_init for non SD 2.0 compatible cards.
+
+ Cards which are not compatible with SD 2.0 standard, may return response
+ for CMD8 command, but it will be invalid in terms of SD 2.0. We should
+ accept this case as admissible, just like Linux does.
+
+ Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit 998be3dd59ed0af4bec38324047fecfa88ac45db
+Author: Rabin Vincent <rabin@rab.in>
+Date: Sun Apr 5 13:30:56 2009 +0530
+
+ mmc: drop unnecessary casts
+
+ Now that response is a uint, we can drop all the casts.
+
+ Signed-off-by: Rabin Vincent <rabin@rab.in>
+
+commit 0b453ffe28bb9227d86ddbe0893bd19c93f04ed7
+Author: Rabin Vincent <rabin@rab.in>
+Date: Sun Apr 5 13:30:55 2009 +0530
+
+ mmc: fix response decoding on little endian
+
+ The mmc code defines the response as an array of chars. However, it
+ access the response bytes both as (i) an array of four uints (with
+ casts) and (ii) as individual chars. The former case is used more
+ often, including by the driver when it assigns the response.
+
+ The char-wise accesses are broken on little endian systems because they
+ assume that the bytes in the uints are in big endian byte order.
+
+ This patch fixes this by changing the response to be an array of four
+ uints and replacing the char-wise accesses with equivalent uint-wise
+ accesses.
+
+ Signed-off-by: Rabin Vincent <rabin@rab.in>
+
+commit 9b1f942c09dd942e6de3185caa81c111b14de567
+Author: Rabin Vincent <rabin@rab.in>
+Date: Sun Apr 5 13:30:54 2009 +0530
+
+ mmc: use lldiv to fix arm eabi build
+
+ The generic MMC core uses direct long long divisions, which do not build
+ with ARM EABI toolchains. Use lldiv() instead, which works everywhere.
+
+ Signed-off-by: Rabin Vincent <rabin@rab.in>
+
+commit e85649c7e683faea1ccfddc9fa9abc62f38e4201
+Author: Rabin Vincent <rabin@rab.in>
+Date: Sun Apr 5 13:30:53 2009 +0530
+
+ mmc: check find_mmc_device return value
+
+ find_mmc_device returns NULL if an invalid device number is specified.
+ Check for this to avoid dereferencing NULL pointers.
+
+ Signed-off-by: Rabin Vincent <rabin@rab.in>
+
+commit ac0865ff33870cdf2cd480165045e1bc311e9fa2
+Author: Rabin Vincent <rabin@rab.in>
+Date: Sun Apr 5 13:30:52 2009 +0530
+
+ mmc: clean up help texts
+
+ Remove some repeated words and superfluous newlines in the mmc command
+ help entries.
+
+ Signed-off-by: Rabin Vincent <rabin@rab.in>
+
+commit 7d6900ebe16d679c0e03f8d1584b64057a64ce39
+Author: Mike Frysinger <vapier@gentoo.org>
+Date: Fri May 29 17:01:48 2009 -0400
+
+ Blackfin: spi: fix pin handling of SPI0 SSEL4
+
+ CS4 on SPI0 has a dedicated PH8 pin which needs to be enabled as a
+ peripheral in order to work.
+
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit 2157359dad2533987f5eb0181ef543693fad6a33
+Author: Mike Frysinger <vapier@gentoo.org>
+Date: Tue May 26 02:51:57 2009 -0400
+
+ Blackfin: fix if() logic in bootrom evt1 check
+
+ A missing set of parenthesis caused the silicon revision to apply only to
+ the BF533 and not the BF531/BF532 variants.
+
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit 76b5883da2cf049cd410901c04ea450e5f5c27c3
+Author: Stefan Roese <sr@denx.de>
+Date: Sat May 16 12:04:22 2009 +0200
+
+ jffs2/mtdparts: Fix problem with usage from JFFS2 and MTDPARTS together
+
+ Currently using JFFS2 with MTDPARTS enabled doesn't work. This is because
+ mtdparts_init() is available in both files, cmd_mtdparts.c and
+ cmd_jffs2.c. Please note that in the original cmd_jffs2.c file (before
+ the jffs2/mtdparts command/file split those 2 different versions
+ already existed. So this is nothing new. The main problem is that the
+ variables "current_dev" and "current_partnum" are declared in both
+ files now. This doesn't work.
+
+ This patch now changes the names of those variable to more specific
+ names: "current_mtd_dev" and "current_mtd_partnum". This is because
+ this patch also changes the declaration from static to global, so
+ that they can be used from both files.
+
+ Please note that my first tests were not successful. The MTD devices
+ selected via mtdparts are now accessed but I'm failing to see the
+ directory listed via the "ls" command. Nothing is displayed. Perhaps
+ I didn't generate the JFFS2 image correctly (I never used JFFS2 in
+ U-Boot before). Not sure. Perhaps somebody else could take a look at
+ this as well. I'll continue looking into this on Monday.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+ Cc: Wolfgang Denk <wd@denx.de>
+ Cc: Detlev Zundel <dzu@denx.de>
+ Cc: Ilya Yanok <yanok@emcraft.com>
+ Cc: Renaud barbier <renaud.barbier@ge.com>
+
+commit ab687907980fa28940a1a992d3f1c5d17cdbbf5d
+Author: Graf Yang <graf.yang@analog.com>
+Date: Sun May 24 02:34:34 2009 -0400
+
+ Blackfin: bf518f-ezbrd: setup portmux for async flash
+
+ The pins for async memory where parallel flash lives are not enabled by
+ default, so make sure we mux them as needed.
+
+ Signed-off-by: Graf Yang <graf.yang@analog.com>
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit f40f6db278f602b55820693634a7256b0b4e4b80
+Author: Stefan Roese <sr@denx.de>
+Date: Wed May 20 10:58:03 2009 +0200
+
+ nand: Fix problem with ECC ordering for PPC4xx NDFC platforms
+
+ This patch enables Smart Media (SMC) ECC byte ordering which is used
+ on the PPC4xx NAND FLASH controller (NDFC). Without this patch we have
+ incompatible ECC byte ordering to the Linux kernel NDFC driver.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+ Acked-by: Scott Wood <scottwood@freescale.com>
+
+commit 399aab7748bef053d59612211e1bd7a3fabfce18
+Author: Stefan Roese <sr@denx.de>
+Date: Wed May 20 10:58:02 2009 +0200
+
+ ppc4xx: Fix problem with ECC ordering for PPC4xx NDFC platforms
+
+ This patch now uses the correct ECC byte order (Smart Media - SMC)
+ to be used on the 4xx NAND FLASH driver. Without this patch we have
+ incompatible ECC byte ordering to the Linux kernel NDFC driver.
+
+ Please note that we also have to enable CONFIG_MTD_NAND_ECC_SMC in
+ drivers/mtd/nand/nand_ecc.c for correct operation. This is done with
+ a seperate patch.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+ Acked-by: Scott Wood <scottwood@freescale.com>
+
+commit 5d841fac8249a2b3f9a814da2140132be0a9f60d
+Author: Stefan Roese <sr@denx.de>
+Date: Wed May 20 10:58:01 2009 +0200
+
+ ppc4xx: Move definition for PPC4xx NAND FLASH controller to header
+
+ This patch moves the definition for the PPC4xx NAND FLASH controller
+ (NDFC) CONFIG_NAND_NDFC into include/ppc4xx.h. This is needed for the
+ upcoming fix for the ECC byte ordering of the NDFC driver.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+ Acked-by: Scott Wood <scottwood@freescale.com>
+
+commit 2df72b82bc9e17b88dc82735a067749220beb025
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Tue May 19 12:53:36 2009 -0500
+
+ common: fix inline--weak error spotted by gcc 4.4
+
+ cmd_ide.c:547: error: inline function 'ide_inb' cannot be declared weak
+
+ removing the inline attribute fixes it.
+
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
+
+commit 9fd9abedcc3c10cf89353265cbe05f58609d51f3
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Tue May 19 12:53:32 2009 -0500
+
+ TQM834x: remove defines causing gcc4.4 warnings
+
+ Configuring for TQM834x board...
+ cpu_init.c: In function 'cpu_init_f':
+ cpu_init.c:262: warning: array subscript is above array bounds
+ cpu_init.c:263: warning: array subscript is above array bounds
+ cpu_init.c:270: warning: array subscript is above array bounds
+ ...
+
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
+
+commit 0850301747228a3327f2815a85284d26ade3de95
+Author: Andreas Huber <andreas.huber@keymile.com>
+Date: Tue May 19 11:06:30 2009 +0200
+
+ UBI: fix return code in ubi_volume_read
+
+ Return -ENODEV instead of 0 when trying to read from a non existing volume.
+
+ Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit ec01481ddc4cf302c7f6d760b776ca94819ec21e
+Author: Graf Yang <graf.yang@analog.com>
+Date: Tue May 19 04:40:08 2009 -0400
+
+ Blackfin: fix timer_init()/timer_reset()
+
+ The timer_init() function was not using the right csync instruction, nor
+ was it doing it right after disabling the core timer.
+
+ The timer_reset() function would reset the timestamp, but not the actual
+ timer, so there was a common edge case where get_timer() return a jump of
+ one timestamp (couple milliseconds) right after resetting. This caused
+ many functions to improperly timeout right away.
+
+ Signed-off-by: Graf Yang <graf.yang@analog.com>
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit c06326c73bf90e48a8e1cf8893ad31c575423f50
+Author: Shinya Kuribayashi <skuribay@pobox.com>
+Date: Sat May 16 09:12:09 2009 +0900
+
+ MIPS: lib_mips/board.c: Remove unused variables
+
+ This fixes the following build warnings:
+
+ board.c: In function 'board_init_r':
+ board.c:328: warning: unused variable 'i'
+ board.c:326: warning: unused variable 'e'
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
+
+commit 47f6a36cc3f3427cc8e4f1d0f3e6678be6f33769
+Author: Shinya Kuribayashi <skuribay@pobox.com>
+Date: Sat May 16 09:12:09 2009 +0900
+
+ MIPS: Make all extern-ed functions in bitops.h static
+
+ All these functions are expected to be static inline-ed.
+ This patch also fixes the following build warnings on MIPS targets:
+
+ include/asm/bitops.h: In function 'ext2_find_next_zero_bit':
+ include/asm/bitops.h:862: warning: '__fswab32' is static but used in inline function 'ext2_find_next_zero_bit' which is not static
+ include/asm/bitops.h:885: warning: '__fswab32' is static but used in inline function 'ext2_find_next_zero_bit' which is not static
+ include/asm/bitops.h:887: warning: '__fswab32' is static but used in inline function 'ext2_find_next_zero_bit' which is not static
+
+ Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
+
+commit 87423d740b91329b8d1d0b73cafd6930993b558a
+Author: Thomas Lange <thomas@corelatus.se>
+Date: Fri Apr 24 16:22:16 2009 +0200
+
+ MIPS: Implement ethernet halt for au1x00
+
+ Implement ethernet halt() by putting MAC0 in reset.
+ If we do not do this, we will get memory corruption
+ when ethernet frames are received during early OS boot.
+
+ Signed-off-by: Thomas Lange <thomas@corelatus.se>
+ Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
+
+commit a2e0ffcf2d9a22c582a93e84a4bef20fd3877f47
+Author: Wolfgang Denk <wd@denx.de>
+Date: Fri May 15 23:29:23 2009 +0200
+
+ Prepare v2009.06-rc2
+
+ Update CHANGELOG.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit f4317ea91942f44cc1c433277927b61618e9b0a5
+Author: Daniel Mack <daniel@caiaq.de>
+Date: Tue May 5 12:48:29 2009 +0200
+
+ ARM: fix PXA build by defining UP2OCR
+
+ U-Boot does not currently build for PXA platforms with USB support
+ enabled:
+
+ usb.c:46: error: 'UP2OCR' undeclared (first use in this function)
+
+ Signed-off-by: Daniel Mack <daniel@caiaq.de>
+ Cc: Markus Klotzbuecher <mk@denx.de>
+
+ Edited commit message.
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit e26ad0eabd10a8cda51920fbcfe4da5b4ccf0c98
+Author: Wolfgang Denk <wd@denx.de>
+Date: Fri May 15 22:32:57 2009 +0200
+
+ Minor Coding Style fix; update CHANGELOG.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit af75a45d23b72a59ac5cc0427696c7f634fdc94b
+Author: Wolfgang Denk <wd@denx.de>
+Date: Fri May 15 09:27:58 2009 +0200
+
+ IDE: bail out of dev_print() for unknown device types
+
+ Commit 574b319512 introduced a subtle bug by mixing a list of tests
+ for "dev_desc->type" and "dev_desc->if_type" into one switch(), which
+ then mostly did not work because "dev_desc->type" cannot take any
+ "IF_*" type values. A later fix in commit 8ec6e332ea changed the
+ switch() into testing "dev_desc->if_type", but at this point the
+ initial test for unknown device types was completely lost, which
+ resulted in output like that for IDE ports without device attached:
+
+ Device 1: Model: Firm: Ser#:
+ Type: # 1F #
+ Capacity: not available
+
+ This patch re-introduces the missing test for unknown device types.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+ Cc: Stefan Roese <sr@denx.de>
+ Cc: Detlev Zundel <dzu@denx.de>
+ Tested-by: Stefan Roese <sr@denx.de>
+
+commit c21f62d8483fbab44cd98d93ff2e9355a330d225
+Author: Stefan Roese <sr@denx.de>
+Date: Thu May 14 07:25:13 2009 +0200
+
+ 74xx_7xx: Fix rounding problem in CPU frequency calculation
+
+ This patch fixes a problem in the CPU frequency calculation. Without it
+ a 798MHz CPU is displayed as 368.503 MHz. And with it it's 798 MHz.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 3ad8a0517b724782ab36f2b554a94de4c00c1adb
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Wed May 13 22:24:12 2009 +0200
+
+ console.h: remove unused prototype 'console_realloc'
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 84bf7ca522e94ec402a1264b01971b924b7e268f
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Wed May 13 22:16:31 2009 +0200
+
+ api: remove un-needed ifdef CONFIG_API already handle by the Makefile
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 792a09eb9d5d8c4f74b7e9f2e887316d511a4e80
+Author: Detlev Zundel <dzu@denx.de>
+Date: Wed May 13 10:54:10 2009 +0200
+
+ Fix e-mail address of Gary Jennejohn.
+
+ Signed-off-by: Detlev Zundel <dzu@denx.de>
+
+commit 5e2c08c3ac90808e9be64856916bfd6df984823c
+Author: Emil Medve <Emilian.Medve@Freescale.com>
+Date: Tue May 12 13:48:32 2009 -0500
+
+ Remove inline qualifier from show_boot_progress()
+
+ The 'inline' is conflicting with the semantic of 'weak' attribute and with the
+ way the show_boot_progress() function is used.
+
+ Also gcc 4.4 is complaining about it:
+
+ main.c:51: error: inline function 'show_boot_progress' cannot be declared weak
+
+ Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
+
+commit fe6da4837308aa33d537ac3e7f36c2d66e3d9a36
+Author: Wolfgang Denk <wd@denx.de>
+Date: Tue May 12 15:17:35 2009 +0200
+
+ MPC8260: fixup device tree by property instead of path
+
+ cpu/mpc8260/cpu.c used to use do_fixup_by_path_u32() to update the
+ clock frequencies in the device tree, using a CPU path
+ "/cpus/OF_CPU", with OF_CPU beind defined in the board config file.
+
+ However, this does not work when one board config file (here:
+ MPC8260ADS.h) is intended to be used for several diffrent CPUs and
+ therefor contains a generic definition like "cpu@0", as the device
+ trees that will then be loaded will contain specific names like
+ "PowerPC,8272@0".
+
+ We switch to using do_fixup_by_prop_u32() instead, so we can search
+ for device_type="cpu", as it is done in other architectures, too.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+ Cc: Heiko Schocher <hs@denx.de>
+ Acked-by: Heiko Schocher <hs@denx.de>
+ Tested-by: Heiko Schocher <hs@denx.de>
+
+commit 12a6753155716e5c3c181a8f40e8b2d3d669aefd
+Author: Rohit Hagargundgi <h.rohit@samsung.com>
+Date: Mon Mar 9 19:45:46 2009 +0530
+
+ Fix OneNAND ipl to read CONFIG_SYS_MONITOR_LEN
+
+ Add CONFIG_SYS_MONITOR_LEN macro to apollon board config.
+ CONFIG_SYS_MONITOR_LEN defines the U-Boot image size.
+ and is used by OneNAND ipl when reading U-Boot image.
+
+ Signed-off-by: Rohit Hagargundgi <h.rohit at samsung.com>
+ Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
+
+commit c404cc5884b0c82fd82d751dbd8e8b3f8919a23a
+Author: Ben Warren <biggerbadderben@gmail.com>
+Date: Tue Apr 28 17:04:51 2009 -0700
+
+ Schedule removal of non-CONFIG_NET_MULTI net driver API
+
+ This will make CONFIG_NET_MULTI the only net driver configuration and
+ we'll be able to remove this option.
+
+ Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
+
+commit 60bbcf0cc6e55095dd186e59a557d584b9b56eb1
+Author: Detlev Zundel <dzu@denx.de>
+Date: Tue May 5 16:04:06 2009 +0200
+
+ powerpc/inka4x0: Remove left-over ide reset code.
+
+ The pin which was used in preliminary versions of the board for ide
+ reset is really connected to the rtc clock.
+
+ Signed-off-by: Detlev Zundel <dzu@denx.de>
+
+commit f578a2da6770951239ad91ee9a1875fdc71dbe48
+Author: Marco Stornelli <marco.stornelli@gmail.com>
+Date: Tue Apr 28 19:04:02 2009 +0200
+
+ Add imls utility command
+
+ This patch adds, under tools folder, a new command called imls. Its
+ goal is the same of UBoot's imls but it can be used as Linux shell
+ command. It reads from raw mtd partition and prints the list of the
+ stored images.
+
+ Signed-off-by: Marco Stornelli <marco.stornelli@gmail.com>
+
+commit da95427ce431908714ae5e9f663ee6e2bc3bcc33
+Author: Heiko Schocher <hs@denx.de>
+Date: Tue Apr 28 08:36:11 2009 +0200
+
+ netloop: updates for NetLoop
+
+ Fix some issues introduced from commit:
+ 2f70c49e5b9813635ad73666aa30f304c7fdeda9
+ suggested by Mike Frysinger.
+
+ - added some comment for the env_id variable in common_cmd_nvedit.c
+ - moved some variables in fn scope instead of file scope
+ - NetInitLoop now static void
+
+ Signed-off-by: Heiko Schocher <hs@denx.de>
+ Acked-by: Ben Warren <biggerbadderben@gmail.com>
+
+commit 3c1d89545de11822f8b5afb5646a57757620bd95
+Author: Heiko Schocher <hs@denx.de>
+Date: Tue Apr 28 07:48:39 2009 +0200
+
+ 82xx, ids8247: added ids8247 board to MAKEALL script
+
+ Signed-off-by: Heiko Schocher <hs@denx.de>
+
+commit 890a017a8a995c921d1e889d360e8d6538ceecfe
+Author: Detlev Zundel <dzu@denx.de>
+Date: Thu May 7 13:08:55 2009 +0200
+
+ arm/imx31_phycore: Fix bi_arch_number
+
+ Signed-off-by: Detlev Zundel <dzu@denx.de>
+ Cc: Sascha Hauer <s.hauer@pengutronix.de>
+
+commit ee47bfabefeb25bdfc83f49ef3bae0f325d3e69e
+Author: Sascha Hauer <s.hauer@pengutronix.de>
+Date: Fri May 15 10:21:33 2009 +0200
+
+ remove myself as phycore/litekit Maintainer
+
+ I never acked a patch that adds me as phycore i.MX31 maintainer nor was
+ it me who pushed the patches, so remove myself from the maintainer list
+ so that other people do not longer wait for my ack.
+
+ Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
+
+commit c63254ef5628efe1c77cb2fdba20753f9666f55d
+Author: Sergey Lapin <slapin@ossfans.org>
+Date: Tue May 12 12:25:14 2009 +0400
+
+ AFEB9260 network fix
+
+ AFEB9260 uses PA10, PA11 for ETX2 and ETX3.
+ Also, due to extarnal pull-up on IRQ line, Micrel PHY ID is 1 after reset sequence,
+ not 0.
+
+ Signed-off-by: Sergey Lapin <slapin@ossfans.org>
+
+commit f8ddcd58221cab63dd25c2324dd2032487f748b1
+Author: Graf Yang <graf.yang@analog.com>
+Date: Tue May 5 02:26:27 2009 -0400
+
+ Blackfin: bf518f-ezbrd: reset ethernet PHY during init
+
+ We don't know what state the ethernet PHY is in when starting up, so make
+ sure we set it to a sane state. This fixes troubles seen when Linux boots
+ up, configures the PHY is a non-default state, and then the system reboots
+ into U-Boot which previously expected a reset state only.
+
+ Signed-off-by: Graf Yang <graf.yang@analog.com>
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit 53310b88eaa27fb5cb83144d0b22389190ad87a1
+Author: Mike Frysinger <vapier@gentoo.org>
+Date: Tue May 5 01:35:41 2009 -0400
+
+ Blackfin: bf527-ezkit: fix SPI flash env params
+
+ The BF527-EZKIT settings for storing the environment in SPI flash wasn't
+ using the correct sector settings for the SPI flash part that is actually
+ on the board.
+
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit f58bf804a14324c6c9186a7a664fa23281780e8b
+Author: Mike Frysinger <vapier@gentoo.org>
+Date: Fri Apr 24 23:54:19 2009 -0400
+
+ Blackfin: avoid get_sclk() with early serial debug
+
+ When the clock functions were changed to use cached values (and thereby
+ avoiding expensive math functions), early serial debug broke because the
+ baud programming is called before external memory is available.
+
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit 02778f2f1b4b1a28b492367477db27c58d45ae35
+Author: Mike Frysinger <vapier@gentoo.org>
+Date: Fri Apr 24 23:39:41 2009 -0400
+
+ Blackfin: fix booting with older bootroms (no EVT1)
+
+ When dropping jump block support, the assumption was that all bootroms
+ supported entry point redirection via the EVT1 register. Unfortunately,
+ this turned out to be incorrect for the oldest Blackfin parts (BF533-0.2
+ and older and BF561). No one really noticed earlier because these parts
+ usually are booted by bypassing the bootrom entirely, and older BF533
+ parts are not supported at all (too many anomalies).
+
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit af2c37378f203857d5e6c957e77a14c2da5b59d2
+Author: Mike Frysinger <vapier@gentoo.org>
+Date: Fri Apr 24 23:22:48 2009 -0400
+
+ Blackfin: recurse with early serial initcode
+
+ Make sure we recurse through serial_putc() rather than bang on the UART
+ transmit register directly to avoid hardware overflows when using \n.
+
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit 6b8edfde22acc574b5532e9f086e6a7287a9bc78
+Author: Wolfgang Denk <wd@denx.de>
+Date: Fri May 1 21:59:12 2009 +0200
+
+ Prepare v2009.06-rc1
+
+ Update CHANGELOG.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 6b2beb5626a143ca5347e7d2c6005be9936c1fbb
+Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+Date: Fri May 1 15:38:06 2009 +0200
+
+ at91: remove lowlevel_init.S
+
+ lowlevel_init.S is not used any more so remove it.
+ As consequence, we also don't have to generate u-boot.lds
+ but can use a static version as before.
+
+ This also fixes the out-of-tree build problem introduced
+ with commit f0a2c7b4 "at91: add support for the PM9263 board"
+
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 0ee7a310479640ef17ce2fc0f6c13cf7961d2330
+Author: Wolfgang Denk <wd@denx.de>
+Date: Fri May 1 00:16:11 2009 +0200
+
+ Update CHANGELOG; minor coding style cleanup.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit d3a513c23ba4100d6983161cdc1f747dfd087bbd
+Author: Manikandan Pillai <mani.pillai@ti.com>
+Date: Tue Apr 21 17:29:05 2009 +0200
+
+ OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
+
+ Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
+ Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>
+
+commit ac9140037a84629c5583066ff1a177396c47d89d
+Author: Dirk Behme <dirk.behme@googlemail.com>
+Date: Fri Apr 17 14:27:56 2009 +0200
+
+ OMAP3: Beagle: Set pinmux conditionally for Rev C boards
+
+ The Beagle Rev C boards pull UART2 from an alternate set of balls.
+
+ Signed-off-by: Steve Sakoman <steve@sakoman.com>
+ Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
+
+commit c1a0fd5f2864e9d381f4a3dc948942cac974e89a
+Author: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
+Date: Mon Apr 27 18:33:33 2009 +0200
+
+ ubifs: BUG: Blocks commpressed with zlib
+
+ Blocks compressed with zlib dont have the full gzip header.
+
+ Without this patch, block compressed with zlib cannot be readed!
+
+ Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
+
+commit 35f6a943f7d92145d607c1d55f5c2e2eae5be630
+Author: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
+Date: Mon Apr 27 18:33:32 2009 +0200
+
+ lib_generic: gunzip: New function zunzip
+
+ Separate gunzip in
+
+ gunzip: Find the end of the header and call zunzip.
+ zunzip: Inflate gunzip block without header.
+
+ UBI fs blocks can be compresed in lzo, zlib or no-compression. The
+ current implementation of u-boot supported all the compressions but
+ there was a bug in the implementation of the zlib blocks.
+
+ UBIFS's Zlib blocks do not have header but they were compressed using
+ gunzip, a function used to decompress gunzip files/sectors with a
+ header.
+
+ This patch adds a new function zunzip that uncompress a zlib block with
+ no header.
+
+ Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
+
+commit a1e5f93185d0d85a4b3fad3b6c743cddcd373b0c
+Author: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
+Date: Thu Apr 23 15:37:16 2009 +0200
+
+ at91: fixed plla calc when no USB support is active
+
+ Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
+ Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 3791a1187c1401c33c9512595e6e89dbb46230c5
+Author: Ladislav Michl <ladis@linux-mips.org>
+Date: Wed Apr 22 01:12:04 2009 +0200
+
+ arm925t: Fix CONFIG_SYS_HZ to 1000
+
+ Let CONFIG_SYS_HZ to have value of 1000 effectively fixing all users of
+ get_timer.
+
+ Changes since original version:
+ * Set PTV=2 (divisor 8) for boards using 12MHz timer clock source to
+ improve timer resolution.
+
+ Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
+
+commit 42bf4b2248146abdc592bde0009c6ea42067f437
+Author: Dirk Behme <dirk.behme@googlemail.com>
+Date: Tue Apr 14 20:15:17 2009 +0200
+
+ OMAP3: Remove legacy NAND defines
+
+ Remove remaining legacy NAND defines for Beagle, EVM, Overo and Pandora.
+
+ Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
+
+commit cba0b778dd5f1ea32959b6825c7f0a31501a99d5
+Author: Sanjeev Premi <premi@ti.com>
+Date: Mon Apr 27 21:27:54 2009 +0530
+
+ OMAP3: Print correct silicon revision
+
+ The function display_board_info() displays incorrect
+ silicon revision - based on the return value from
+ function get_cpu_rev().
+
+ This patch fixes the problem.
+
+ Signed-off-by: Sanjeev Premi <premi@ti.com>
+
+commit 90006e9b33bcdbf241b0295d186e3634137907a9
+Author: Sanjeev Premi <premi@ti.com>
+Date: Mon Apr 27 21:27:44 2009 +0530
+
+ OMAP3: Remove unused board-types
+
+ The board-types defined in struct omap3_sysinfo seem to be
+ unused. The function display_board_info() is passed
+ board type as an argument; which is ignored.
+
+ This patch removes all uses of board-type, related definitions
+ and functions.
+
+ Signed-off-by: Sanjeev Premi <premi@ti.com>
+
+commit 6a6b62e3aa4b340c4f8fc67b1487ddb5436c684d
+Author: Sanjeev Premi <premi@ti.com>
+Date: Mon Apr 27 21:27:27 2009 +0530
+
+ OMAP3: Use functions print_cpuinfo() and checkboard()
+
+ Use the functions print_cpuinfo() and checkboard() to
+ display the cpu and board specific information.
+
+ These functions reuse content from the existing function
+ display_board_info() - which has been removed.
+
+ Also, updated the existig OMAP3 configurations to
+ define:
+ - CONFIG_DISPLAY_CPUINFO
+ - CONFIG_DISPLAY_BOARDINFO
+
+ Signed-off-by: Sanjeev Premi <premi@ti.com>
+
+commit f8e2b3107ee00f2782f8ebf47e3f09cda4e2353a
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Mar 18 11:17:37 2009 +0100
+
+ MTD: Change cfi-mtd to accept non-uniform sector sizes
+
+ With this patch non-uniform NOR FLASH chips (chips with multiple erase
+ regions) can be exported via the cfi-mtd layer and therefor used by UBI.
+ We select the largest sector size as erasesize. The cfi driver will make
+ sure that the smaller sectors are handled correctly.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 3dcbe628d66b648e954bc8147d4faff2983206d9
+Author: Anatolij Gustschin <agust@denx.de>
+Date: Thu Apr 23 12:35:22 2009 +0200
+
+ video: fix bug in cfb_console.c code
+
+ Fix bug in drawing long version/info strings:
+ U-Boot version string like
+ "U-Boot 2009.03-05647-g7c51e06 (Apr 23 2009 - 12:40:00) MPC83XX"
+ is long and doesn't wrap around correctly while drawing
+ beside the logo. Such long strings partially overwrite
+ the logo. This patch is an attempt to fix it.
+
+ Signed-off-by: Anatolij Gustschin <agust@denx.de>
+
+commit 4d9eab89b3b2c2ed432b14d355a56f274d8aac75
+Author: Wolfgang Denk <wd@denx.de>
+Date: Tue Apr 28 08:50:31 2009 +0200
+
+ cmd_ext2.c: fix compile warnings
+
+ Get rid of these warnings:
+
+ cmd_ext2.c:247: warning: format '%ld' expects type 'long int', but argument 2 has type 'int'
+ cmd_ext2.c:248: warning: format '%lX' expects type 'long unsigned int', but argument 3 has type 'int'
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 28afe0160f87ff74574150d703055a965f91422a
+Author: Heiko Schocher <hs@denx.de>
+Date: Mon Apr 27 10:48:20 2009 +0200
+
+ ids8247: Remove legacy NAND defines
+
+ because legacy NAND support is deprecated converting to current
+ NAND interface. !This just compile, because I have no more the
+ hardware to test it.
+
+ Signed-off-by: Heiko Schocher <hs@denx.de>
+
+commit dbd33614404b65aa441c5620c3dbd560c4460c09
+Author: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
+Date: Mon Apr 27 09:13:31 2009 +0200
+
+ ubifs: BUG realpath string must be ended with NULL
+
+ If the memory used to copy the link_make is "dirty" the string wont
+ be ended with NULL, throwing out multiple memory bugs.
+
+ Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
+ Acked-by: Stefan Roese <sr@denx.de>
+
+commit 65351a8793c51f3787efbbcf3aa1df0ad543c127
+Author: Peter Tyser <ptyser@xes-inc.com>
+Date: Fri Apr 24 15:59:56 2009 -0500
+
+ bmp_logo: Check return value of fread()
+
+ Add basic error handling to fread() function calls. This prevents
+ compililation warnings such as:
+
+ bmp_logo.c: In function ‘main’:
+ bmp_logo.c:71: warning: ignoring return value of ‘fread’, declared with
+ attribute warn_unused_result
+ ...
+
+ Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
+
+commit eea8be86d1c2b570660d1f6c553845e13164231a
+Author: Peter Tyser <ptyser@xes-inc.com>
+Date: Fri Apr 24 15:59:46 2009 -0500
+
+ ncb: Check return value of write()
+
+ This prevents the compilation warning:
+
+ ncb.c: In function 'main':
+ ncb.c:32: warning: ignoring return value of ‘write’, declared with
+ attribute warn_unused_result
+
+ Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
+
+commit dbe29e36a4c2775b69b5a63b0ce2bac89c08e691
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Apr 24 15:59:35 2009 +0200
+
+ mtd: nand/onenand: Register mtd device upon device scanning
+
+ With this patch the NAND and OneNAND devices are registered in the MTD
+ subsystem and can then be referenced by the mtdcore code (e.g.
+ get_mtd_device_nm()). This is needed for the new "ubi part" command
+ syntax without the flash type parameter (nor|nand|onenand).
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 10bb62d85a0850dbad1fdd34123378686373f166
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Apr 24 15:58:33 2009 +0200
+
+ mtd: nand: Include linux/mtd/partitions.h in nand_base.h
+
+ This patch removes this compilation warning when CONFIG_MTD_PARTITIONS is
+ defined:
+
+ nand_base.c: In function 'nand_release':
+ nand_base.c:2922: warning: implicit declaration of function 'del_mtd_partitions'
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 2d579e5060413af5a740cb396dc87e1ff31bf5a9
+Author: Stefan Roese <sr@denx.de>
+Date: Fri Apr 24 20:24:19 2009 +0200
+
+ ubi: Remove flash selection parameter (nor|nand|onenand) from "ubi part"
+
+ This patch removes the now unnecessary flash type parameter from the
+ "ubi part" command. Currently the user has to define the type of flash
+ he will be using UBI on. Example:
+
+ => ubi part nor partition1
+
+ With this patch this type parameter is not needed anymore. The user can
+ now select the partition directly without the flash type paramter.
+ Example:
+
+ => ubi part partition1
+
+ This breaks backward compatibility right now because of the change in the
+ command syntax. But UBI support is still quite fresh and the advantage of
+ this new command is syntax big enough for this change. Additionally the
+ code is much cleaner now.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+ CC: Kyungmin Park <kyungmin.park@samsung.com>
+
+commit 294f10ca9ea82a15e135dcb0fc658382ab206940
+Author: Detlev Zundel <dzu@denx.de>
+Date: Thu Apr 23 13:14:20 2009 +0200
+
+ mips/vcth: Use generic 16550 uart driver
+
+ As the common code also handles baudrate switching, which the board
+ specific vct.c driver did not support, this is one of the rare
+ occassions where deleting code actually adds a feature :)
+
+ Signed-off-by: Detlev Zundel <dzu@denx.de>
+ Acked-by: Stefan Roese <sr@denx.de>
+ Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
+
+commit 0c8a84916c5dacccdc5b27b63fc463e9f3b04f07
+Author: Ladislav Michl <ladis@linux-mips.org>
+Date: Tue Apr 21 02:26:31 2009 +0200
+
+ Separate mtdparts command from jffs2
+
+ On Thu, Mar 19, 2009 at 01:30:36PM +0100, Stefan Roese wrote:
+ > Currently the mtdparts commands are included in the jffs2 command support.
+ > This doesn't make sense anymore since other commands (e.g. UBI) use this
+ > infrastructure as well now. This patch separates the mtdparts commands from
+ > the jffs2 commands making it possible to only select mtdparts when no JFFS2
+ > support is needed.
+
+ One more leftover... Let nboot command know about partitions even if JFFS2
+ support is not enabled.
+
+ Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
+ Acked-by: Stefan Roese <sr@denx.de>
+
+commit 67c2e57c0875139dbfcd6f41c43e6ad0cb2e40c9
+Author: Peter Tyser <ptyser@xes-inc.com>
+Date: Mon Apr 20 11:22:13 2009 -0500
+
+ cmd_ide: Remove unused AmigaOneG3SE code
+
+ The output_data_short() and input_data_short() functions for the
+ AmigaOneG3SE are unused and result in compiler warnings.
+
+ Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
+
+commit c93c102ace00764a56dbdf78bac134a23906721e
+Author: Peter Tyser <ptyser@xes-inc.com>
+Date: Mon Apr 20 11:21:40 2009 -0500
+
+ AmigaOneG3SE: Fix CONFIG_CMD_CONSOLE definition
+
+ Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
+
+commit 54e822f9590cc6c70411bd8cabd42236e07a2aa7
+Author: Peter Tyser <ptyser@xes-inc.com>
+Date: Mon Apr 20 11:09:05 2009 -0500
+
+ Replace __asm references with __asm__
+
+ __asm__ follows gcc's documented syntax and is generally more common
+ than __asm. This change is only asthetic and should not affect
+ functionality.
+
+ Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
+
+commit f9a109b3adc5e8647535357500e2a38f0558b5c2
+Author: Peter Tyser <ptyser@xes-inc.com>
+Date: Mon Apr 20 11:08:46 2009 -0500
+
+ Replace __attribute references with __attribute__
+
+ __attribute__ follows gcc's documented syntax and is generally more
+ common than __attribute. This change is only asthetic and should not
+ affect functionality.
+
+ Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
+
+commit 08f077da9298ff65cc6f85f90d2770000a1beee9
+Author: David Brownell <dbrownell@users.sourceforge.net>
+Date: Thu Apr 16 19:55:48 2009 -0700
+
+ mtdpart command: align output columns
+
+ Make the headers in the "mtdparts" command output line up
+ with their columns ... strike the extra TAB character.
+
+ Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
+
+commit 06f41f825c23344d889d5419bb5eaeceb3ed2a02
+Author: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
+Date: Thu Apr 16 10:51:03 2009 +0900
+
+ Remove sa1100.h
+
+ sa1100.h is not used anywhere, then remove it.
+
+ $ find . -name '*.h' -empty -print
+ ./include/sa1100.h
+ $ git grep 'sa1100.h' .
+ $
+
+ Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
+ Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+
+commit 7d3d30b1b3fbd0a07db254ead99fa6fff4f4d992
+Author: Stefan Roese <sr@denx.de>
+Date: Tue Apr 14 17:51:21 2009 +0200
+
+ UBIFS: Remove tnc_commit.c which is not used in the read-only version
+
+ I missed removing this file while implementing the UBIFS support. It's
+ not referenced at all, so let's remove it. Thanks to Artem Bityutskiy
+ for spotting.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 6356daff70867822bdb23cea49f98e65421a25b8
+Author: Adrian Hunter <adrian.hunter@nokia.com>
+Date: Tue Apr 14 17:50:38 2009 +0200
+
+ UBIFS: fix recovery bug
+
+ UBIFS did not recovery in a situation in which it could
+ have. The relevant function assumed there could not be
+ more nodes in an eraseblock after a corrupted node, but
+ in fact the last (NAND) page written might contain anything.
+ The correct approach is to check for empty space (0xFF bytes)
+ from then on.
+
+ Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 351f40caf2f7806b2cefb93e077ea619b9f684e8
+Author: Gao Guanhua <B22826@freescale.com>
+Date: Tue Apr 14 14:37:35 2009 +0800
+
+ fs: Fix the wrong type of var
+
+ The filelen should be signed type, not unsigned type.
+ otherwise, The condition as below never take.
+ if (filelen < 0)
+
+ Signed-off-by: Gao Guanhua <B22826@freescale.com>
+ Signed-off-by: Dave Liu <daveliu@freescale.com>
+
+commit 05f474c4d0469bebc0bb05df60a39dc7fdf28e62
+Author: Wolfgang Denk <wd@denx.de>
+Date: Tue Apr 28 00:29:34 2009 +0200
+
+ Update CHANGELOG
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
commit ad74cae9ff8790727bc81ee91c6bca7d50dca446
Author: David Brownell <dbrownell@users.sourceforge.net>
Date: Thu Apr 16 23:15:15 2009 -0700
Tested-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
+commit a85693b3bd4431b05b7df608b6f7733c0f80c53e
+Author: Dirk Behme <dirk.behme@googlemail.com>
+Date: Tue Apr 21 17:30:51 2009 +0200
+
+ OMAP3: Fix changed mmc init command
+
+ In recent U-Boot mmcinit changed to mmc init.
+
+ Signed-off-by: Steve Sakoman <steve@sakoman.com>
+ Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
+
commit 34b76a14f676bc6501c27a96564e4dfb4793f033
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Apr 26 20:39:26 2009 +0200
Signed-off-by: Wolfgang Denk <wd@denx.de>
+commit 7239c5da5e9197accb3dfe395be4502c3b9bca8e
+Author: David Brownell <dbrownell@users.sourceforge.net>
+Date: Sun Apr 12 15:40:16 2009 -0700
+
+ minor DaVinci clock cleanup
+
+ Minor cleanup to clock-related defines for DaVinci DM6446 boards:
+
+ - CONFIG_SYS_CLK_FREQ is unused; remove it.
+
+ - CONFIG_SYS_NS16550_CLK must be the same as CONFIG_SYS_HZ_CLOCK
+
+ On DM6446 both of those peripheral clocks actually come from the
+ same source, the primary oscillator. Having them use the same
+ symbol avoids bugs in the clone'n'modify development cycle.
+
+ Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
+
+commit ffd8c7170d55c34bbfcfd2c84093dcaff796cbf3
+Author: Minkyu Kang <mk7.kang@samsung.com>
+Date: Mon Apr 6 19:59:29 2009 +0900
+
+ s3c64xx: remove unnecessary definition
+
+ CONFIG_S3C6400 is must defined at config header file
+ That definition is unnecessary at this file
+
+ Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
+
commit 14b9308d511b53042ef478936e367a67282df66a
Author: Heiko Schocher <hs@denx.de>
Date: Fri Apr 24 06:50:45 2009 +0200
projects / u-boot / blobdiff