Changes since U-Boot 1.1.4:
======================================================================
+* Add rudimentary handling of alternate settings of USB interfaces.
+ This is in order to fix issues with some USB sticks or knives timing
+ out during initialisation. Some code readability improvements.
+
+* Enable buffered flash writes for TQM5200 board.
+
+* Fix problems with SanDisk Corporation Cruzer Micro USB memory stick.
+
+* Add support for TQM885D board.
+ Patch by Martin Krause, 20 Mar 2006
+
+* Fix FEC initialisation: All MII configuration is done via FEC1
+ registers, but MII_SPEED was configured according to FEC used. So
+ if only FEC2 was used, this caused the real MII_SPEED register in
+ FEC1 to stay uninitalised, leqading to "mii_send STUCK!" messages.
+ Fix: always configure MII_SPEED on FEC1 only.
+ Patch by Markus Klotzbuecher, 12 Jul 2006
+
+* Add support for SPC1920 board.
+ Patch by Markus Klotzbuecher, 12 Jul 2006
+
+* MCC200 board: support console on any one of the Quad UART ports.
+
+* Fix error in flash protection calculation on MCC200 board.
+
+* Major PCMCIA Cleanup to make code better readable and maintainable.
+ Notes:
+ - Board-dependend code for RPXLITE and RPXCLASSIC-based boards
+ placed to the drivers/rpx_pmcia.c file to avoid duplication.
+ Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
+ - drivers/i82365.c has been split into two parts located at
+ board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
+ the only boards using CONFIG_82365).
+ - Changes were tested for clean build and *very* *few* boards.
+
+* Fix timer problems on AMCC yucca board.
+ Set Timer Clock Select to use CPU clock as a timer input source.
+
+* Bring yucca config more in line with other AMCC boards.
+
+* Add AMCC bamboo board to MAKEALL build script.
+
+* Fix AMCC bamboo eval board compilation errors.
+
+* Add system memory to the PCI region list for AMCC PPC44x CPUs.
+ Enabled it for Yucca board.
+
+* Cleanup config file and bootup output for Yucca board.
+
+* Fix CONFIG_440_GX define usage.
+
+* Remove autogenerated bmp_logo.h file.
+
+* Add support for AMCC 440SPe CPU based eval board (Yucca).
+
+* Call serial_initialize() before first debug() is used.
+
+* Cleanup trab board for GCC-4.x
+
+* VoiceBlue update: use new MTD flash partitioning methods, use more
+ reasonable TEXT_BASE, update default environment and enable keyed
+ autoboot.
+ Patch by Ladislav Michl, 16. Aug 2005
+
+* Add forgotten changes for the PLEB 2 Board.
+ Patch by David Snowdon, 13. Aug 2005
+
+* Add support for wrPPMC7xx/74xx boards
+ Patch by Richard Danter, 12 Aug 2005
+
+* Add support for gth2 board
+ Patch by Thomas Lange, Aug 11 2005
+
+* Add support for CONFIG_SERIAL_MULTI on MPC5xxx
+ Patch by Martin Krause, 8 Jun 2006
+
+ This patch supports two serial consoles on boards with
+ a MPC5xxx CPU. The console can be switched at runtime
+ by setting stdin, stdout and stderr to the desired serial
+ interface (serial0 or serial1). The PSCs to be used as
+ console port are definded by CONFIG_PSC_CONSOLE
+ and CONFIG_PSC_CONSOLE2.
+ See README.serial_multi for details.
+
+* Bugfix in I2C initialisation on S3C2400.
+ If the bus is blocked because of a previously interrupted
+ transfer, up to eleven clocks are generated on the I2CSCL
+ line to complete the transfer and to free the bus.
+ With this fix pin I2CSCL (PG6) is really configured as GPIO
+ so the clock pulses are really generated.
+ Patch by Martin Krause, 04 Apr 2006
+
+* Fix DDR6 errata on TQM834x boards
+ Patch by Thomas Waehner, 07 Mar 2006
+
* Remove obsolete flash driver board/tqm5200/flash.c
Patch by Martin Krause, 11 Jan 2006
* Change mtdparts definition on trab board to match current flash map
Patch by Martin Krause, 27 Oct 2005
+* Fix memory init problems on MCC200 board
+
+* Fix IxEthDB.h to compile again
+ Patch by Stefan Roese, 14 Jun 2006
+
+* Minor cleanup for PCS440EP board
+ Patch by Stefan Roese, 13 Jun 2006
+
* Add MCF5282 support (without preloader)
relocate ichache_State to ram
u-boot can run from internal flash
projects / u-boot / blobdiff