Changes since U-Boot 1.1.4:
======================================================================
+* Code cleanup
+
+* Update NetStar board
+ Patch by Ladislav Michl, 03 Nov 2005
+
+* Make code better readable.
+ Patch by Ladislav Michl, 14 Sep 2005
+
+* Enable initrd ATAG for xm250 board.
+ Patch by Josef Wagner, 05 Sep 2005
+
+* Add readline cmdline-editing extension
+ Patch by JinHua Luo, 01 Sep 2005
+
+* Add support for friendly-arm SBC-2410X board
+ Patch by JinHua Luo, 01 Sep 2005
+
+* Fix multi-part image support on i386 platform.
+ Patch by David Updegraff, 19 Aug 2005
+
+* Add support for KVME080 board
+ Patch by Sangmoon Kim, 18 Aug 2005
+
+* Fix MIPS LE build problem
+ Patch by Matej Kupljen, 10 Aug 2005
+
+* Check argument count in "mii" command.
+ Problem pointed out by Andrew Dyer, 13 Jun 2005
+
+* Cleanup TQM5200 board configurations:
+ - make highboot configurations use environment at high end, too,
+ to avoid flash fragmentation
+ - always use redundand environment
+ - don't enable video code for modules without graphics controller
+ - provide useful (though different) mtdparts settings
+ - get rid of CONFIG_CS_AUTOCONF which was always set anyway
+
+* Extend mkconfig tool to print more useful target name
+
+* Add support for high-boot on TQM5200 and TQM5200S boards.
+ Hint: the CPLD on the TQM5200 must be programmed with a software
+ version supporting the high boot option! The new TQM5200S is
+ already supporting this option. On the TQM5200 this option will be
+ supported in configurations with MPC5200 rev B processors.
+ To actually "high boot", set jumper X30 on the STK52xx.
+ Patch by Martin Krause, 12 Jul 2006
+
+* Add support for new TQM5200 revisions
+ - Support for TQM5200S (short version without graphic controller)
+ - Support for modules with 'N' type S29GL128N Spansion flashes
+ (requires changes to flash layout)
+ - Support for MPC5200B cpu (mostly support for second SDRAM bank)
+ Patch by Martin Krause, 07 Jul 2006
+
+* Fix support for PS/2 keyboard on TQM85xx boards
+ The PS/2 keyobard driver for the TQM85xx modules only supports the
+ internal DUART of the MPC85xx CPU. Since the MPC8560 doesn't
+ include a DUART, the TQM8560 modules can't be used with the PS/2
+ keyboard controller on the STK85xx board.
+ The PS/2 keyboard driver should work with the modules TQM8540,
+ TQM8541 and TQM8555, but it only has been tested on a TQM8540, yet.
+ Make sure the PS/2 controller on the STK85xx is programmed. Jumper
+ settings: X66 1-2, 9-10; X61 2-3
+ Patch by Martin Krause, 21 Jun 2006
+
+* Adjust RTC century handling on STK52xx board to match Linux driver.
+ Patch by Martin Krause, 12 Jun 2006
+
+* Adjust filenames for USB update images on TRAB board.
+ During an automatic update via USB stick, U-Boot searches for
+ images with the name "firmware.img" and "kernel.img". This names
+ are now changed to "firmw_01.img" and "kernl_01.img". This is done,
+ to prevent updates of new boards (with the new macronics "c" step
+ flashes) with old, incompatible firmware or kernel versions.
+ Patch by Martin Krause, 21 Jun 2006
+
+* Bugfix in VFD routine on TRAB board.
+ Make sure upper lext pixel can be set to blue, too
+ (so far only red was possible).
+ Patch by Martin Krause, 15 Feb 2006
+
+* Enable buffered flash writes for TB5200 board.
+
+* Fix some bugs in TRAB board flash driver.
+ - increase CFG_FLASH_ERASE_TOUT from 2 to 15 seconds
+ - use CFG_FLASH_WRITE_TOUT for programming instead of CFG_FLASH_ERASE_TOUT
+ - remove "Unlock Bypass" mode, because macronix flashes do not support
+ this mode officially
+ - fix flash reset command from 0x00FF to 0x00F0. 0x00FF is only specified
+ for Intel compatible flashes, not for AMD compatible.
+ Patch by Martin Krause, 15 Feb 2006
+
+* Add additional error messages to flash driver on TRAB board
+ (for erase errors and timeout errors)
+ Patch by Martin Krause, 14 Feb 2006
+
+* Add support for TB5200 board
+ The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module
+ integrated in a little aluminium case.
+ Patch by Martin Krause, 8 Jun 2006
+
+* Enable buffered flash writes for TQM5200 board.
+
+* Fix problems with SanDisk Corporation Cruzer Micro USB memory stick.
+
+* Add support for TQM885D board.
+ Patch by Martin Krause, 20 Mar 2006
+
+* Fix FEC initialisation: All MII configuration is done via FEC1
+ registers, but MII_SPEED was configured according to FEC used. So
+ if only FEC2 was used, this caused the real MII_SPEED register in
+ FEC1 to stay uninitalised, leqading to "mii_send STUCK!" messages.
+ Fix: always configure MII_SPEED on FEC1 only.
+ Patch by Markus Klotzbuecher, 12 Jul 2006
+
+* Add support for SPC1920 board.
+ Patch by Markus Klotzbuecher, 12 Jul 2006
+
+* MCC200 board: support console on any one of the Quad UART ports.
+
+* Fix error in flash protection calculation on MCC200 board.
+
* Major PCMCIA Cleanup to make code better readable and maintainable.
Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
* VoiceBlue update: use new MTD flash partitioning methods, use more
reasonable TEXT_BASE, update default environment and enable keyed
autoboot.
- Patch by Ladislav Michl, 16. Aug 2005
+ Patch by Ladislav Michl, 16. Aug 2005
* Add forgotten changes for the PLEB 2 Board.
Patch by David Snowdon, 13. Aug 2005
* Add support for wrPPMC7xx/74xx boards
Patch by Richard Danter, 12 Aug 2005
-
+
* Add support for gth2 board
Patch by Thomas Lange, Aug 11 2005
With this fix pin I2CSCL (PG6) is really configured as GPIO
so the clock pulses are really generated.
Patch by Martin Krause, 04 Apr 2006
-
+
* Fix DDR6 errata on TQM834x boards
Patch by Thomas Waehner, 07 Mar 2006
has been programmed. Jumper Settings: X66 1-2, 9-10; X61 2-3
* Fix TRAB channel switching delay for trab_fkt.bin standalone applikation
- In tsc2000_read_channel() the delay after setting the multiplexer
+ In tsc2000_read_channel() the delay after setting the multiplexer
to a temperature channel is increased from 1,5 ms to 10 ms. This
is to allow the multiplexer inputs to stabilize after huge steps
of the input signal level.
projects / u-boot / blobdiff