mkimage: fit: spl: Add an optional static offset for external data

[u-boot] / README

diff --git a/README b/README
index 88ff837d7c984c32fa715c95d0145289eab41b37..03bed180591a7a0cafd003f53b889991c183741e 100644 (file)
--- a/README
+++ b/README
@@ -1003,6 +1003,7 @@ The following options need to be configured:
                CONFIG_CMD_ECHO           echo arguments
                CONFIG_CMD_EDITENV        edit env variable
                CONFIG_CMD_EEPROM       * EEPROM read/write support
+               CONFIG_CMD_EEPROM_LAYOUT* EEPROM layout aware commands
                CONFIG_CMD_ELF          * bootelf, bootvx
                CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
                CONFIG_CMD_ENV_FLAGS    * display details about env flags
@@ -1066,7 +1067,7 @@ The following options need to be configured:
                CONFIG_CMD_RUN            run command in env variable
                CONFIG_CMD_SANDBOX      * sb command to access sandbox features
                CONFIG_CMD_SAVES        * save S record dump
-               CONFIG_CMD_SCSI         * SCSI Support
+               CONFIG_SCSI             * SCSI Support
                CONFIG_CMD_SDRAM        * print SDRAM configuration information
                                          (requires CONFIG_CMD_I2C)
                CONFIG_CMD_SETGETDCR      Support for DCR Register access
@@ -1254,7 +1255,7 @@ The following options need to be configured:
                CONFIG_MTD_PARTITIONS  Memory Technology Device partition table.
 
                If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
-               CONFIG_CMD_SCSI) you must configure support for at
+               CONFIG_SCSI) you must configure support for at
                least one non-MTD partition type as well.
 
 - IDE Reset method:
@@ -3487,6 +3488,10 @@ FIT uImage format:
                consider that a completely unreadable NAND block is bad,
                and thus should be skipped silently.
 
+               CONFIG_SPL_ABORT_ON_RAW_IMAGE
+               When defined, SPL will proceed to another boot method
+               if the image it has loaded does not have a signature.
+
                CONFIG_SPL_RELOC_STACK
                Adress of the start of the stack SPL will use after
                relocation.  If unspecified, this is equal to
@@ -4043,16 +4048,6 @@ Configuration Settings:
        If defined, don't allow the -f switch to env set override variable
        access flags.
 
-- CONFIG_SYS_GENERIC_BOARD
-       This selects the architecture-generic board system instead of the
-       architecture-specific board files. It is intended to move boards
-       to this new framework over time. Defining this will disable the
-       arch/foo/lib/board.c file and use common/board_f.c and
-       common/board_r.c instead. To use this option your architecture
-       must support it (i.e. must select HAVE_GENERIC_BOARD in arch/Kconfig).
-       If you find problems enabling this option on your board please report
-       the problem and send patches!
-
 - CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
        This is set by OMAP boards for the max time that reset should
        be asserted. See doc/README.omap-reset-time for details on how
@@ -4829,6 +4824,11 @@ Low Level (hardware related) configuration options:
                other boot loader or by a debugger which performs
                these initializations itself.
 
+- CONFIG_SKIP_LOWLEVEL_INIT_ONLY
+               [ARM926EJ-S only] This allows just the call to lowlevel_init()
+               to be skipped. The normal CPU15 init (such as enabling the
+               instruction cache) is still performed.
+
 - CONFIG_SPL_BUILD
                Modifies the behaviour of start.S when compiling a loader
                that is executed before the actual U-Boot. E.g. when