- i386 Files specific to i386 CPUs
- ixp Files specific to Intel XScale IXP CPUs
- mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
+ - mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
+ - mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
- mips Files specific to MIPS CPUs
- mpc5xx Files specific to Freescale MPC5xx CPUs
- mpc5xxx Files specific to Freescale MPC5xxx CPUs
The following options need to be configured:
-- CPU Type: Define exactly one of
-
- PowerPC based CPUs:
- -------------------
- CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
- or CONFIG_MPC5xx
- or CONFIG_MPC8220
- or CONFIG_MPC824X, CONFIG_MPC8260
- or CONFIG_MPC85xx
- or CONFIG_IOP480
- or CONFIG_405GP
- or CONFIG_405EP
- or CONFIG_440
- or CONFIG_MPC74xx
- or CONFIG_750FX
-
- ARM based CPUs:
- ---------------
- CONFIG_SA1110
- CONFIG_ARM7
- CONFIG_PXA250
- CONFIG_CPU_MONAHANS
-
- MicroBlaze based CPUs:
- ----------------------
- CONFIG_MICROBLAZE
-
- Nios-2 based CPUs:
- ----------------------
- CONFIG_NIOS2
-
- AVR32 based CPUs:
- ----------------------
- CONFIG_AT32AP
-
-- Board Type: Define exactly one of
-
- PowerPC based boards:
- ---------------------
-
- CONFIG_ADCIOP CONFIG_FPS860L CONFIG_OXC
- CONFIG_ADS860 CONFIG_GEN860T CONFIG_PCI405
- CONFIG_AMX860 CONFIG_GENIETV CONFIG_PCIPPC2
- CONFIG_AP1000 CONFIG_GTH CONFIG_PCIPPC6
- CONFIG_AR405 CONFIG_gw8260 CONFIG_pcu_e
- CONFIG_BAB7xx CONFIG_hermes CONFIG_PIP405
- CONFIG_BC3450 CONFIG_hymod CONFIG_PM826
- CONFIG_c2mon CONFIG_IAD210 CONFIG_ppmc8260
- CONFIG_CANBT CONFIG_ICU862 CONFIG_QS823
- CONFIG_CCM CONFIG_IP860 CONFIG_QS850
- CONFIG_CMI CONFIG_IPHASE4539 CONFIG_QS860T
- CONFIG_cogent_mpc8260 CONFIG_IVML24 CONFIG_RBC823
- CONFIG_cogent_mpc8xx CONFIG_IVML24_128 CONFIG_RPXClassic
- CONFIG_CPCI405 CONFIG_IVML24_256 CONFIG_RPXlite
- CONFIG_CPCI4052 CONFIG_IVMS8 CONFIG_RPXsuper
- CONFIG_CPCIISER4 CONFIG_IVMS8_128 CONFIG_rsdproto
- CONFIG_CPU86 CONFIG_IVMS8_256 CONFIG_sacsng
- CONFIG_CRAYL1 CONFIG_JSE CONFIG_Sandpoint8240
- CONFIG_CSB272 CONFIG_LANTEC CONFIG_Sandpoint8245
- CONFIG_CU824 CONFIG_LITE5200B CONFIG_sbc8260
- CONFIG_DASA_SIM CONFIG_lwmon CONFIG_sbc8560
- CONFIG_DB64360 CONFIG_MBX CONFIG_SM850
- CONFIG_DB64460 CONFIG_MBX860T CONFIG_SPD823TS
- CONFIG_DU405 CONFIG_MHPC CONFIG_STXGP3
- CONFIG_DUET_ADS CONFIG_MIP405 CONFIG_SXNI855T
- CONFIG_EBONY CONFIG_MOUSSE CONFIG_TQM823L
- CONFIG_ELPPC CONFIG_MPC8260ADS CONFIG_TQM8260
- CONFIG_ELPT860 CONFIG_MPC8540ADS CONFIG_TQM850L
- CONFIG_ep8260 CONFIG_MPC8540EVAL CONFIG_TQM855L
- CONFIG_ERIC CONFIG_MPC8560ADS CONFIG_TQM860L
- CONFIG_ESTEEM192E CONFIG_MUSENKI CONFIG_TTTech
- CONFIG_ETX094 CONFIG_MVS1 CONFIG_UTX8245
- CONFIG_EVB64260 CONFIG_NETPHONE CONFIG_V37
- CONFIG_FADS823 CONFIG_NETTA CONFIG_W7OLMC
- CONFIG_FADS850SAR CONFIG_NETVIA CONFIG_W7OLMG
- CONFIG_FADS860T CONFIG_NX823 CONFIG_WALNUT
- CONFIG_FLAGADM CONFIG_OCRTC CONFIG_ZPC1900
- CONFIG_FPS850L CONFIG_ORSG CONFIG_ZUMA
-
- ARM based boards:
- -----------------
-
- CONFIG_ARMADILLO, CONFIG_AT91RM9200DK, CONFIG_CERF250,
- CONFIG_CSB637, CONFIG_DELTA, CONFIG_DNP1110,
- CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE,
- CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610,
- CONFIG_KB9202, CONFIG_LART, CONFIG_LPD7A400,
- CONFIG_LUBBOCK, CONFIG_OSK_OMAP5912, CONFIG_OMAP2420H4,
- CONFIG_PLEB2, CONFIG_SHANNON, CONFIG_P2_OMAP730,
- CONFIG_SMDK2400, CONFIG_SMDK2410, CONFIG_TRAB,
- CONFIG_VCMA9
-
- MicroBlaze based boards:
- ------------------------
-
- CONFIG_SUZAKU
-
- Nios-2 based boards:
- ------------------------
-
- CONFIG_PCI5441 CONFIG_PK1C20
- CONFIG_EP1C20 CONFIG_EP1S10 CONFIG_EP1S40
-
- AVR32 based boards:
- -------------------
-
- CONFIG_ATSTK1000
+- CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
+
+- Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
- CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
Define exactly one of
CONFIG_OF_LIBFDT
* New libfdt-based support
* Adds the "fdt" command
- * The bootm command does _not_ modify the fdt
+ * The bootm command automatically updates the fdt
CONFIG_OF_FLAT_TREE
* Deprecated, see CONFIG_OF_LIBFDT
* The environment variable "disable_of", when set,
disables this functionality.
- CONFIG_OF_FLAT_TREE_MAX_SIZE
-
- The maximum size of the constructed OF tree.
-
OF_CPU - The proper name of the cpus node.
OF_SOC - The proper name of the soc node.
OF_TBCLK - The timebase frequency.
OF_STDOUT_PATH - The path to the console device
+ boards with QUICC Engines require OF_QE to set UCC mac addresses
+
CONFIG_OF_HAS_BD_T
* CONFIG_OF_LIBFDT - enables the "fdt bd_t" command
CONFIG_OF_HAS_UBOOT_ENV
- * CONFIG_OF_LIBFDT - enables the "fdt bd_t" command
+ * CONFIG_OF_LIBFDT - enables the "fdt env" command
* CONFIG_OF_FLAT_TREE - The resulting flat device tree
will have a copy of u-boot's environment variables
CONFIG_USB_CONFIG
for differential drivers: 0x00001000
for single ended drivers: 0x00005000
+ CFG_USB_EVENT_POLL
+ May be defined to allow interrupt polling
+ instead of using asynchronous interrupts
+
+- USB Device:
+ Define the below if you wish to use the USB console.
+ Once firmware is rebuilt from a serial console issue the
+ command "setenv stdin usbtty; setenv stdout usbtty" and
+ attach your usb cable. The Unix command "dmesg" should print
+ it has found a new device. The environment variable usbtty
+ can be set to gserial or cdc_acm to enable your device to
+ appear to a USB host as a Linux gserial device or a
+ Common Device Class Abstract Control Model serial device.
+ If you select usbtty = gserial you should be able to enumerate
+ a Linux host by
+ # modprobe usbserial vendor=0xVendorID product=0xProductID
+ else if using cdc_acm, simply setting the environment
+ variable usbtty to be cdc_acm should suffice. The following
+ might be defined in YourBoardName.h
+
+ CONFIG_USB_DEVICE
+ Define this to build a UDC device
+
+ CONFIG_USB_TTY
+ Define this to have a tty type of device available to
+ talk to the UDC device
+
+ CFG_CONSOLE_IS_IN_ENV
+ Define this if you want stdin, stdout &/or stderr to
+ be set to usbtty.
+
+ mpc8xx:
+ CFG_USB_EXTC_CLK 0xBLAH
+ Derive USB clock from external clock "blah"
+ - CFG_USB_EXTC_CLK 0x02
+
+ CFG_USB_BRG_CLK 0xBLAH
+ Derive USB clock from brgclk
+ - CFG_USB_BRG_CLK 0x04
+
+ If you have a USB-IF assigned VendorID then you may wish to
+ define your own vendor specific values either in BoardName.h
+ or directly in usbd_vendor_info.h. If you don't define
+ CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
+ CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
+ should pretend to be a Linux device to it's target host.
+
+ CONFIG_USBD_MANUFACTURER
+ Define this string as the name of your company for
+ - CONFIG_USBD_MANUFACTURER "my company"
+
+ CONFIG_USBD_PRODUCT_NAME
+ Define this string as the name of your product
+ - CONFIG_USBD_PRODUCT_NAME "acme usb device"
+
+ CONFIG_USBD_VENDORID
+ Define this as your assigned Vendor ID from the USB
+ Implementors Forum. This *must* be a genuine Vendor ID
+ to avoid polluting the USB namespace.
+ - CONFIG_USBD_VENDORID 0xFFFF
+
+ CONFIG_USBD_PRODUCTID
+ Define this as the unique Product ID
+ for your device
+ - CONFIG_USBD_PRODUCTID 0xFFFF
- MMC Support:
Defines a default value for theIP address of a TFTP
server to contact when using the "tftboot" command.
+- Multicast TFTP Mode:
+ CONFIG_MCAST_TFTP
+
+ Defines whether you want to support multicast TFTP as per
+ rfc-2090; for example to work with atftp. Lets lots of targets
+ tftp down the same boot image concurrently. Note: the ethernet
+ driver in use must provide a function: mcast() to join/leave a
+ multicast group.
+
+ CONFIG_BOOTP_RANDOM_DELAY
- BOOTP Recovery Mode:
CONFIG_BOOTP_RANDOM_DELAY
boot, thus flooding the BOOTP server. Defining
CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
inserted before sending out BOOTP requests. The
- following delays are insterted then:
+ following delays are inserted then:
1st BOOTP request: delay 0 ... 1 sec
2nd BOOTP request: delay 0 ... 2 sec
BOOTP requests: delay 0 ... 8 sec
- DHCP Advanced Options:
- CONFIG_BOOTP_MASK
-
- You can fine tune the DHCP functionality by adding
- these flags to the CONFIG_BOOTP_MASK define:
+ You can fine tune the DHCP functionality by defining
+ CONFIG_BOOTP_* symbols:
+
+ CONFIG_BOOTP_SUBNETMASK
+ CONFIG_BOOTP_GATEWAY
+ CONFIG_BOOTP_HOSTNAME
+ CONFIG_BOOTP_NISDOMAIN
+ CONFIG_BOOTP_BOOTPATH
+ CONFIG_BOOTP_BOOTFILESIZE
+ CONFIG_BOOTP_DNS
+ CONFIG_BOOTP_DNS2
+ CONFIG_BOOTP_SEND_HOSTNAME
+ CONFIG_BOOTP_NTPSERVER
+ CONFIG_BOOTP_TIMEOFFSET
+ CONFIG_BOOTP_VENDOREX
+
+ CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
+ environment variable, not the BOOTP server.
CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
serverip from a DHCP server, it is possible that more
serverip will be stored in the additional environment
variable "dnsip2". The first DNS serverip is always
stored in the variable "dnsip", when CONFIG_BOOTP_DNS
- is added to the CONFIG_BOOTP_MASK.
+ is defined.
CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
to do a dynamic update of a DNS server. To do this, they
need the hostname of the DHCP requester.
- If CONFIG_BOOP_SEND_HOSTNAME is added to the
- CONFIG_BOOTP_MASK, the content of the "hostname"
- environment variable is passed as option 12 to
- the DHCP server.
+ If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
+ of the "hostname" environment variable is passed as
+ option 12 to the DHCP server.
- CDP Options:
CONFIG_CDP_DEVICE_ID
-31 post/post.c POST test failed, detected by post_output_backlog()
-32 post/post.c POST test failed, detected by post_run_single()
- -1 common/cmd_doc.c Bad usage of "doc" command
- -1 common/cmd_doc.c No boot device
- -1 common/cmd_doc.c Unknown Chip ID on boot device
- -1 common/cmd_doc.c Read Error on boot device
- -1 common/cmd_doc.c Image header has bad magic number
-
- -1 common/cmd_ide.c Bad usage of "ide" command
- -1 common/cmd_ide.c No boot device
- -1 common/cmd_ide.c Unknown boot device
- -1 common/cmd_ide.c Unknown partition table
- -1 common/cmd_ide.c Invalid partition type
- -1 common/cmd_ide.c Read Error on boot device
- -1 common/cmd_ide.c Image header has bad magic number
-
- -1 common/cmd_nand.c Bad usage of "nand" command
- -1 common/cmd_nand.c No boot device
- -1 common/cmd_nand.c Unknown Chip ID on boot device
- -1 common/cmd_nand.c Read Error on boot device
- -1 common/cmd_nand.c Image header has bad magic number
-
- -1 common/env_common.c Environment has a bad CRC, using default
-
+ 34 common/cmd_doc.c before loading a Image from a DOC device
+ -35 common/cmd_doc.c Bad usage of "doc" command
+ 35 common/cmd_doc.c correct usage of "doc" command
+ -36 common/cmd_doc.c No boot device
+ 36 common/cmd_doc.c correct boot device
+ -37 common/cmd_doc.c Unknown Chip ID on boot device
+ 37 common/cmd_doc.c correct chip ID found, device available
+ -38 common/cmd_doc.c Read Error on boot device
+ 38 common/cmd_doc.c reading Image header from DOC device OK
+ -39 common/cmd_doc.c Image header has bad magic number
+ 39 common/cmd_doc.c Image header has correct magic number
+ -40 common/cmd_doc.c Error reading Image from DOC device
+ 40 common/cmd_doc.c Image header has correct magic number
+ 41 common/cmd_ide.c before loading a Image from a IDE device
+ -42 common/cmd_ide.c Bad usage of "ide" command
+ 42 common/cmd_ide.c correct usage of "ide" command
+ -43 common/cmd_ide.c No boot device
+ 43 common/cmd_ide.c boot device found
+ -44 common/cmd_ide.c Device not available
+ 44 common/cmd_ide.c Device available
+ -45 common/cmd_ide.c wrong partition selected
+ 45 common/cmd_ide.c partition selected
+ -46 common/cmd_ide.c Unknown partition table
+ 46 common/cmd_ide.c valid partition table found
+ -47 common/cmd_ide.c Invalid partition type
+ 47 common/cmd_ide.c correct partition type
+ -48 common/cmd_ide.c Error reading Image Header on boot device
+ 48 common/cmd_ide.c reading Image Header from IDE device OK
+ -49 common/cmd_ide.c Image header has bad magic number
+ 49 common/cmd_ide.c Image header has correct magic number
+ -50 common/cmd_ide.c Image header has bad checksum
+ 50 common/cmd_ide.c Image header has correct checksum
+ -51 common/cmd_ide.c Error reading Image from IDE device
+ 51 common/cmd_ide.c reading Image from IDE device OK
+ 52 common/cmd_nand.c before loading a Image from a NAND device
+ -53 common/cmd_nand.c Bad usage of "nand" command
+ 53 common/cmd_nand.c correct usage of "nand" command
+ -54 common/cmd_nand.c No boot device
+ 54 common/cmd_nand.c boot device found
+ -55 common/cmd_nand.c Unknown Chip ID on boot device
+ 55 common/cmd_nand.c correct chip ID found, device available
+ -56 common/cmd_nand.c Error reading Image Header on boot device
+ 56 common/cmd_nand.c reading Image Header from NAND device OK
+ -57 common/cmd_nand.c Image header has bad magic number
+ 57 common/cmd_nand.c Image header has correct magic number
+ -58 common/cmd_nand.c Error reading Image from NAND device
+ 58 common/cmd_nand.c reading Image from NAND device OK
+
+ -60 common/env_common.c Environment has a bad CRC, using default
+
+ 64 net/eth.c starting with Ethernetconfiguration.
+ -64 net/eth.c no Ethernet found.
+ 65 net/eth.c Ethernet found.
+
+ -80 common/cmd_net.c usage wrong
+ 80 common/cmd_net.c before calling NetLoop()
+ -81 common/cmd_net.c some error in NetLoop() occured
+ 81 common/cmd_net.c NetLoop() back without error
+ -82 common/cmd_net.c size == 0 (File with size 0 loaded)
+ 82 common/cmd_net.c trying automatic boot
+ 83 common/cmd_net.c running autoscript
+ -83 common/cmd_net.c some error in automatic boot or autoscript
+ 84 common/cmd_net.c end without errors
Modem Support:
--------------
make NAME_config
where "NAME_config" is the name of one of the existing
-configurations; the following names are supported:
-
- ADCIOP_config FPS860L_config omap730p2_config
- ADS860_config GEN860T_config pcu_e_config
- Alaska8220_config
- AR405_config GENIETV_config PIP405_config
- at91rm9200dk_config GTH_config QS823_config
- CANBT_config hermes_config QS850_config
- cmi_mpc5xx_config hymod_config QS860T_config
- cogent_common_config IP860_config RPXlite_config
- cogent_mpc8260_config IVML24_config RPXlite_DW_config
- cogent_mpc8xx_config IVMS8_config RPXsuper_config
- CPCI405_config JSE_config rsdproto_config
- CPCIISER4_config LANTEC_config Sandpoint8240_config
- csb272_config lwmon_config sbc8260_config
- CU824_config MBX860T_config sbc8560_33_config
- DUET_ADS_config MBX_config sbc8560_66_config
- EBONY_config mpc7448hpc2_config SM850_config
- ELPT860_config MPC8260ADS_config SPD823TS_config
- ESTEEM192E_config MPC8540ADS_config stxgp3_config
- ETX094_config MPC8540EVAL_config SXNI855T_config
- FADS823_config NMPC8560ADS_config TQM823L_config
- FADS850SAR_config NETVIA_config TQM850L_config
- FADS860T_config omap1510inn_config TQM855L_config
- FPS850L_config omap1610h2_config TQM860L_config
- omap1610inn_config walnut_config
- omap5912osk_config Yukon8220_config
- omap2420h4_config ZPC1900_config
+configurations; see the main Makefile for supported names.
Note: for some board special configuration names may exist; check if
additional information is available from the board vendor; for