specific to be undertaken on a native platform. The sandbox is also used to
run some of U-Boot's tests.
-See board/sandbox/sandbox/README.sandbox for more details.
+See board/sandbox/README.sandbox for more details.
Configuration Options:
interleaving mode, handled by Dickens for Freescale layerscape
SoCs with ARM core.
+ CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
+ Number of controllers used as main memory.
+
+ CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
+ Number of controllers used for other than main memory.
+
+ CONFIG_SYS_FSL_SEC_BE
+ Defines the SEC controller register space as Big Endian
+
+ CONFIG_SYS_FSL_SEC_LE
+ Defines the SEC controller register space as Little Endian
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
exists, unlike the similar options in the Linux kernel. Do not
set these options unless they apply!
-- CPU timer options:
- CONFIG_SYS_HZ
-
- The frequency of the timer returned by get_timer().
- get_timer() must operate in milliseconds and this CONFIG
- option must be set to 1000.
-
- Linux Kernel Interface:
CONFIG_CLOCKS_IN_MHZ
CONFIG_CMD_BMP * BMP support
CONFIG_CMD_BSP * Board specific commands
CONFIG_CMD_BOOTD bootd
+ CONFIG_CMD_BOOTI * ARM64 Linux kernel Image support
CONFIG_CMD_CACHE * icache, dcache
CONFIG_CMD_CLK * clock command support
CONFIG_CMD_CONSOLE coninfo
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
txfilltuning field in the EHCI controller on reset.
+ CONFIG_USB_DWC2_REG_ADDR the physical CPU address of the DWC2
+ HW module registers.
+
- USB Device:
Define the below if you wish to use the USB console.
Once firmware is rebuilt from a serial console issue the
downloads. This buffer should be as large as possible for a
platform. Define this to the size available RAM for fastboot.
+ CONFIG_FASTBOOT_FLASH
+ The fastboot protocol includes a "flash" command for writing
+ the downloaded image to a non-volatile storage device. Define
+ this to enable the "fastboot flash" command.
+
+ CONFIG_FASTBOOT_FLASH_MMC_DEV
+ The fastboot "flash" command requires additional information
+ regarding the non-volatile storage device. Define this to
+ the eMMC device that fastboot should use to store the image.
+
- Journaling Flash filesystem support:
CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
CONFIG_JFFS2_NAND_DEV
200 ms.
- Configuration Management:
+ CONFIG_BUILD_TARGET
+
+ Some SoCs need special image types (e.g. U-Boot binary
+ with a special header) as build targets. By defining
+ CONFIG_BUILD_TARGET in the SoC / board header, this
+ special image will be automatically built upon calling
+ make / MAKEALL.
+
CONFIG_IDENT_STRING
If defined, this string will be added to the U-Boot
Enable auto completion of commands using TAB.
- Note that this feature has NOT been implemented yet
- for the "hush" shell.
-
-
CONFIG_SYS_HUSH_PARSER
Define this variable to enable the "hush" shell (from
The memory will be freed (or in fact just forgotton) when
U-Boot relocates itself.
- Pre-relocation malloc() is only supported on sandbox
+ Pre-relocation malloc() is only supported on ARM and sandbox
at present but is fairly easy to enable for other archs.
- Pre-relocation malloc() is only supported on ARM at present
- but is fairly easy to enable for other archs.
-
- CONFIG_SYS_BOOTM_LEN:
Normally compressed uImages are limited to an
uncompressed size of 8 MBytes. If this is not enough,