that this requires a (stable) reference clock (32 kHz
RTC clock or CONFIG_SYS_8XX_XIN)
+ CONFIG_SYS_DELAYED_ICACHE
+
+ Define this option if you want to enable the
+ ICache only when Code runs from RAM.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
CONFIG_SYS_BAUDRATE_TABLE, see below.
CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
+- Console Rx buffer length
+ With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
+ the maximum receive buffer length for the SMC.
+ This option is actual only for 82xx and 8xx possible.
+ If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
+ must be defined, to setup the maximum idle timeout for
+ the SMC.
+
- Interrupt driven serial port input:
CONFIG_SERIAL_SOFTWARE_FIFO
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
CONFIG_CMD_DOC * Disk-On-Chip Support
+ CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
+ CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
+ CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
+ CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
CONFIG_CMD_DTT * Digital Therm and Thermostat
CONFIG_CMD_ECHO echo arguments
CONFIG_CMD_EEPROM * EEPROM read/write support
CONFIG_CMD_ELF * bootelf, bootvx
- CONFIG_CMD_ENV saveenv
+ CONFIG_CMD_SAVEENV saveenv
CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT partition support
CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_MII * MII utility commands
CONFIG_CMD_NAND * NAND support
CONFIG_CMD_NET bootp, tftpboot, rarpboot
+ CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
+ CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
CONFIG_CMD_PCI * pciinfo
CONFIG_CMD_PCMCIA * PCMCIA support
CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
Note that if the RTC uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
+- GPIO Support:
+ CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
+ CONFIG_PCA953X_INFO - enable pca953x info command
+
+ Note that if the GPIO device uses I2C, then the I2C interface
+ must also be configured. See I2C Support, below.
+
- Timestamp Support:
When CONFIG_TIMESTAMP is selected, the timestamp
Bus on the MPC8260. But it should be not so difficult
to add this option to other architectures.
+ CONFIG_SOFT_I2C_READ_REPEATED_START
+
+ defining this will force the i2c_read() function in
+ the soft_i2c driver to perform an I2C repeated start
+ between writing the address pointer and reading the
+ data. If this define is omitted the default behaviour
+ of doing a stop-start sequence will be used. Most I2C
+ devices can use either method, but some require one or
+ the other.
- SPI Support: CONFIG_SPI
- CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
undefine this when you're short of memory.
+- CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
+ width of the commands listed in the 'help' command output.
+
- CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
prompt for user input.
- CONFIG_SYS_64BIT_STRTOUL:
Adds simple_strtoull that returns a 64bit value
+- CONFIG_NS16550_MIN_FUNCTIONS:
+ Define this if you desire to only have use of the NS16550_init
+ and NS16550_putc functions for the serial driver located at
+ drivers/serial/ns16550.c. This option is useful for saving
+ space for already greatly restricted images, including but not
+ limited to NAND_SPL configurations.
+
Low Level (hardware related) configuration options:
---------------------------------------------------
CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
+- CONFIG_PCI_DISABLE_PCIE:
+ Disable PCI-Express on systems where it is supported but not
+ required.
+
- CONFIG_SPD_EEPROM
Get DDR timing information from an I2C EEPROM. Common
with pluggable memory modules such as SODIMMs
Only for 83xx systems. If specified, then DDR should
be configured using CS0 and CS1 instead of CS2 and CS3.
-- CONFIG_SYS_83XX_DDR_USES_CS0
- Only for 83xx systems. If specified, then DDR should
- be configured using CS0 and CS1 instead of CS2 and CS3.
-
- CONFIG_ETHER_ON_FEC[12]
Define to enable FEC[12] on a 8xx series processor.
Useful on scripts which control the retry operation
themselves.
- npe_ucode - see CONFIG_IXP4XX_NPE_EXT_UCOD
- if set load address for the NPE microcode
+ npe_ucode - set load address for the NPE microcode
tftpsrcport - If this is set, the value is used for TFTP's
UDP source port.
projects / u-boot / blobdiff