#
-# (C) Copyright 2000 - 2009
+# (C) Copyright 2000 - 2011
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
Define this option if you want to enable the
ICache only when Code runs from RAM.
+- 85xx CPU Options:
+ CONFIG_SYS_FSL_TBCLK_DIV
+
+ Defines the core time base clock divider ratio compared to the
+ system clock. On most PQ3 devices this is 8, on newer QorIQ
+ devices it can be 16 or 32. The ratio varies from SoC to Soc.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
define this to a list of base addresses for each (supported)
port. See e.g. include/configs/versatile.h
+ CONFIG_PL011_SERIAL_RLCR
+
+ Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
+ have separate receive and transmit line control registers. Set
+ this variable to initialize the extra register.
+
+ CONFIG_PL011_SERIAL_FLUSH_ON_INIT
+
+ On some platforms (e.g. U8500) U-Boot is loaded by a second stage
+ boot loader that has already initialized the UART. Define this
+ variable to flush the UART at init time.
+
- Console Interface:
Depending on board, define exactly one serial port
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
CONFIG_CMD_GO * the 'go' command (exec code)
+ CONFIG_CMD_GREPENV * search environment
CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
CONFIG_CMD_I2C * I2C serial bus support
CONFIG_CMD_IDE * IDE harddisk support
- Watchdog:
CONFIG_WATCHDOG
If this variable is defined, it enables watchdog
- support. There must be support in the platform specific
- code for a watchdog. For the 8xx and 8260 CPUs, the
- SIU Watchdog feature is enabled in the SYPCR
- register.
+ support for the SoC. There must be support in the SoC
+ specific code for a watchdog. For the 8xx and 8260
+ CPUs, the SIU Watchdog feature is enabled in the SYPCR
+ register. When supported for a specific SoC is
+ available, then no further board specific code should
+ be needed to use it.
+
+ CONFIG_HW_WATCHDOG
+ When using a watchdog circuitry external to the used
+ SoC, then define this variable and provide board
+ specific code for the "hw_watchdog_reset" function.
- U-Boot Version:
CONFIG_VERSION_VARIABLE
CONFIG_VIDEO_LOGO
CONFIG_VIDEO_BMP_LOGO
- The DIU driver will look for the 'monitor' environment variable,
- and if defined, enable the DIU as a console during boot. This
- variable should be set to one of these values:
-
- '0' Output video to the DVI connector
- '1' Output video to the LVDS connector
- '2' Output video to the Dual-Link LVDS connector
+ The DIU driver will look for the 'video-mode' environment
+ variable, and if defined, enable the DIU as a console during
+ boot. See the documentation file README.video for a
+ description of this variable.
- Keyboard Support:
CONFIG_KEYBOARD
driver in use must provide a function: mcast() to join/leave a
multicast group.
- CONFIG_BOOTP_RANDOM_DELAY
- BOOTP Recovery Mode:
CONFIG_BOOTP_RANDOM_DELAY
used) must be put below this limit, unless "bootm_low"
enviroment variable is defined and non-zero. In such case
all data for the Linux kernel must be between "bootm_low"
- and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.
+ and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
+ variable "bootm_mapsize" will override the value of
+ CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
+ then the value in "bootm_size" will be used instead.
- CONFIG_SYS_BOOT_RAMDISK_HIGH:
Enable initrd_high functionality. If defined then the
source code. It is used to make hardware dependant
initializations.
+- CONFIG_IDE_AHB:
+ Most IDE controllers were designed to be connected with PCI
+ interface. Only few of them were designed for AHB interface.
+ When software is doing ATA command and data transfer to
+ IDE devices through IDE-AHB controller, some additional
+ registers accessing to these kind of IDE-AHB controller
+ is requierd.
+
- CONFIG_SYS_IMMR: Physical address of the Internal Memory.
DO NOT CHANGE unless you know exactly what you're
doing! (11-4) [MPC8xx/82xx systems only]
for use by the bootm command. See also "bootm_size"
environment variable. Address defined by "bootm_low" is
also the base of the initial memory mapping for the Linux
- kernel -- see the description of CONFIG_SYS_BOOTMAPSZ.
+ kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
+ bootm_mapsize.
+
+ bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
+ This variable is given as a hexadecimal number and it
+ defines the size of the memory region starting at base
+ address bootm_low that is accessible by the Linux kernel
+ during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
+ as the default value if it is defined, and bootm_size is
+ used otherwise.
bootm_size - Memory range available for image processing in the bootm
command can be restricted. This variable is given as
projects / u-boot / blobdiff