cmd: CONFIG_CMD_LOG select CONFIG_LOG

[u-boot] / README

diff --git a/README b/README
index cce59ad7c05e23c8f95d989a9f3e41b9ea6ef048..6f98e09e680d539246c279a18059c2f38ad7ce10 100644 (file)
--- a/README
+++ b/README
@@ -713,17 +713,6 @@ The following options need to be configured:
                as a convenience, when switching between booting from
                RAM and NFS.
 
-- Bootcount:
-               CONFIG_BOOTCOUNT_ENV
-               If no softreset save registers are found on the hardware
-               "bootcount" is stored in the environment. To prevent a
-               saveenv on all reboots, the environment variable
-               "upgrade_available" is used. If "upgrade_available" is
-               0, "bootcount" is always 0, if "upgrade_available" is
-               1 "bootcount" is incremented in the environment.
-               So the Userspace Applikation must set the "upgrade_available"
-               and "bootcount" variable to 0, if a boot was successfully.
-
 - Pre-Boot Commands:
                CONFIG_PREBOOT
 
@@ -823,14 +812,6 @@ The following options need to be configured:
                CONFIG_AT91_HW_WDT_TIMEOUT
                specify the timeout in seconds. default 2 seconds.
 
-- U-Boot Version:
-               CONFIG_VERSION_VARIABLE
-               If this variable is defined, an environment variable
-               named "ver" is created by U-Boot showing the U-Boot
-               version as printed by the "version" command.
-               Any change to this variable will be reverted at the
-               next reset.
-
 - Real-Time Clock:
 
                When CONFIG_CMD_DATE is selected, the type of the RTC
@@ -1431,10 +1412,6 @@ The following options need to be configured:
                be at least 4MB.
 
 - MII/PHY support:
-               CONFIG_PHY_ADDR
-
-               The address of PHY on MII bus.
-
                CONFIG_PHY_CLOCK_FREQ (ppc4xx)
 
                The clock frequency of the MII bus
@@ -2228,12 +2205,6 @@ The following options need to be configured:
                the environment like the "source" command or the
                boot command first.
 
-               CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-
-               Define this in order to add variables describing certain
-               run-time determined information about the hardware to the
-               environment.  These will be named board_name, board_rev.
-
                CONFIG_DELAY_ENVIRONMENT
 
                Normally the environment is loaded when the board is
@@ -2278,27 +2249,6 @@ The following options need to be configured:
                A better solution is to properly configure the firewall,
                but sometimes that is not allowed.
 
-- bootcount support:
-               CONFIG_AT91SAM9XE
-               enable special bootcounter support on at91sam9xe based boards.
-               CONFIG_SOC_DA8XX
-               enable special bootcounter support on da850 based boards.
-               CONFIG_BOOTCOUNT_RAM
-               enable support for the bootcounter in RAM
-               CONFIG_BOOTCOUNT_I2C
-               enable support for the bootcounter on an i2c (like RTC) device.
-                       CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
-                       CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
-                                                   the bootcounter.
-                       CONFIG_BOOTCOUNT_ALEN = address len
-               CONFIG_BOOTCOUNT_EXT
-               enable support for the bootcounter in EXT filesystem
-                       CONFIG_SYS_BOOTCOUNT_ADDR = RAM address used for read
-                                                    and write.
-                       CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE = interface
-                       CONFIG_SYS_BOOTCOUNT_EXT_DEVPART = device and part
-                       CONFIG_SYS_BOOTCOUNT_EXT_NAME = filename
-
 - Show boot progress:
                CONFIG_SHOW_BOOT_PROGRESS
 
@@ -2518,12 +2468,6 @@ FIT uImage format:
                kernel. Needed for UBI support.
 
 - UBI support
-               CONFIG_UBI_SILENCE_MSG
-
-               Make the verbose messages from UBI stop printing.  This leaves
-               warnings and errors enabled.
-
-
                CONFIG_MTD_UBI_WL_THRESHOLD
                This parameter defines the maximum difference between the highest
                erase counter value and the lowest erase counter value of eraseblocks
@@ -2585,12 +2529,6 @@ FIT uImage format:
                Enable UBI fastmap debug
                default: 0
 
-- UBIFS support
-               CONFIG_UBIFS_SILENCE_MSG
-
-               Make the verbose messages from UBIFS stop printing.  This leaves
-               warnings and errors enabled.
-
 - SPL framework
                CONFIG_SPL
                Enable building of SPL globally.
@@ -2850,9 +2788,6 @@ Configuration Settings:
                Begin and End addresses of the area used by the
                simple memory test.
 
-- CONFIG_SYS_ALT_MEMTEST:
-               Enable an alternate, more extensive memory test.
-
 - CONFIG_SYS_MEMTEST_SCRATCH:
                Scratch address used by the alternate memory test
                You only need to set this if address zero isn't writeable
@@ -3478,9 +3413,6 @@ Low Level (hardware related) configuration options:
                If defined, the x86 reset vector code is included. This is not
                needed when U-Boot is running from Coreboot.
 
-- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
-               Enables the RTC32K OSC on AM33xx based plattforms
-
 - CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
                Option to disable subpage write in NAND driver
                driver that uses this: