- Boot Delay: CONFIG_BOOTDELAY - in seconds
Delay before automatically booting the default image;
set to -1 to disable autoboot.
+ set to -2 to autoboot with no delay and not check for abort
+ (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
See doc/README.autoboot for these options that
work with CONFIG_BOOTDELAY. None are required.
- Monitor Functions:
Monitor commands can be included or excluded
from the build by using the #include files
- "config_cmd_all.h" and #undef'ing unwanted
- commands, or using "config_cmd_default.h"
+ <config_cmd_all.h> and #undef'ing unwanted
+ commands, or using <config_cmd_default.h>
and augmenting with additional #define's
for wanted commands.
CONFIG_CMD_IMLS List all found images
CONFIG_CMD_IMMAP * IMMR dump support
CONFIG_CMD_IMPORTENV * import an environment
+ CONFIG_CMD_INI * import data from an ini file into the env
CONFIG_CMD_IRQ * irqinfo
CONFIG_CMD_ITEST Integer/string test of 2 values
CONFIG_CMD_JFFS2 * JFFS2 Support
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
CONFIG_CMD_TFTPPUT * TFTP put command (upload)
- CONFIG_CMD_TIME * run command and report execution time
+ CONFIG_CMD_TIME * run command and report execution time (ARM specific)
+ CONFIG_CMD_TIMER * access to the system tick timer
CONFIG_CMD_USB * USB support
CONFIG_CMD_CDP * Cisco Discover Protocol support
CONFIG_CMD_MFSL * Microblaze FSL support
If this variable is defined, an environment variable
named "ver" is created by U-Boot showing the U-Boot
version as printed by the "version" command.
- This variable is readonly.
+ Any change to this variable will be reverted at the
+ next reset.
- Real-Time Clock:
commands like bootm or iminfo. This option is
automatically enabled when you select CONFIG_CMD_DATE .
-- Partition Support:
- CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
- and/or CONFIG_ISO_PARTITION and/or CONFIG_EFI_PARTITION
+- Partition Labels (disklabels) Supported:
+ Zero or more of the following:
+ CONFIG_MAC_PARTITION Apple's MacOS partition table.
+ CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
+ Intel architecture, USB sticks, etc.
+ CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
+ CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
+ bootloader. Note 2TB partition limit; see
+ disk/part_efi.c
+ CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
CONFIG_CMD_SCSI) you must configure support for at
- least one partition type as well.
+ least one non-MTD partition type as well.
- IDE Reset method:
CONFIG_IDE_RESET_ROUTINE - this is defined in several
viewport is supported.
To enable the ULPI layer support, define CONFIG_USB_ULPI and
CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
+ If your ULPI phy needs a different reference clock than the
+ standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
+ the appropriate value in Hz.
- MMC Support:
The MMC controller on the Intel PXA is supported. To
can be displayed via the splashscreen support or the
bmp command.
+- Do compresssing for memory range:
+ CONFIG_CMD_ZIP
+
+ If this option is set, it would use zlib deflate method
+ to compress the specified memory at its best effort.
+
- Compression support:
CONFIG_BZIP2
CONFIG_SYS_SPL_MALLOC_SIZE
The size of the malloc pool used in SPL.
+ CONFIG_SPL_FRAMEWORK
+ Enable the SPL framework under common/. This framework
+ supports MMC, NAND and YMODEM loading of U-Boot and NAND
+ NAND loading of the Linux Kernel.
+
+ CONFIG_SPL_DISPLAY_PRINT
+ For ARM, enable an optional function to print more information
+ about the running system.
+
CONFIG_SPL_LIBCOMMON_SUPPORT
Support for common/libcommon.o in SPL binary
CONFIG_SPL_SPI_SUPPORT
Support for drivers/spi/libspi.o in SPL binary
+ CONFIG_SPL_RAM_DEVICE
+ Support for running image already present in ram, in SPL binary
+
CONFIG_SPL_LIBGENERIC_SUPPORT
Support for lib/libgeneric.o in SPL binary
Disable PCI-Express on systems where it is supported but not
required.
+- CONFIG_PCI_ENUM_ONLY
+ Only scan through and get the devices on the busses.
+ Don't do any setup work, presumably because someone or
+ something has already done it, and we don't need to do it
+ a second time. Useful for platforms that are pre-booted
+ by coreboot or similar.
+
- CONFIG_SYS_SRIO:
Chip has SRIO or not
consider minicom to be broken, and recommend not to use it. Under
Unix, I recommend to use C-Kermit for general purpose use (and
especially for kermit binary protocol download ("loadb" command), and
-use "cu" for S-Record download ("loads" command).
+use "cu" for S-Record download ("loads" command). See
+http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.3.
+for help with kermit.
+
Nevertheless, if you absolutely want to use it try adding this
configuration to your "File transfer protocols" section: