implemetation.
CONFIG_SYS_FSL_DDR2
- Board config to use DDR2. It can be eanbeld for SoCs with
+ Board config to use DDR2. It can be enabled for SoCs with
Freescale DDR2 or DDR3 controllers, depending on the board
implementation.
'Sane' compilers will generate smaller code if
CONFIG_PRE_CON_BUF_SZ is a power of 2
-- Boot Delay: CONFIG_BOOTDELAY - in seconds
- Delay before automatically booting the default image;
- set to -1 to disable autoboot.
- set to -2 to autoboot with no delay and not check for abort
- (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
-
- See doc/README.autoboot for these options that
- work with CONFIG_BOOTDELAY. None are required.
- CONFIG_BOOT_RETRY_TIME
- CONFIG_BOOT_RETRY_MIN
- CONFIG_AUTOBOOT_KEYED
- CONFIG_AUTOBOOT_PROMPT
- CONFIG_AUTOBOOT_DELAY_STR
- CONFIG_AUTOBOOT_STOP_STR
- CONFIG_ZERO_BOOTDELAY_CHECK
- CONFIG_RESET_TO_RETRY
-
- Autoboot Command:
CONFIG_BOOTCOMMAND
Only needed when CONFIG_BOOTDELAY is enabled;
CONFIG_CMD_ECHO echo arguments
CONFIG_CMD_EDITENV edit env variable
CONFIG_CMD_EEPROM * EEPROM read/write support
+ CONFIG_CMD_EEPROM_LAYOUT* EEPROM layout aware commands
CONFIG_CMD_ELF * bootelf, bootvx
CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
CONFIG_CMD_ENV_FLAGS * display details about env flags
CONFIG_CMD_RUN run command in env variable
CONFIG_CMD_SANDBOX * sb command to access sandbox features
CONFIG_CMD_SAVES * save S record dump
- CONFIG_CMD_SCSI * SCSI Support
+ CONFIG_SCSI * SCSI Support
CONFIG_CMD_SDRAM * print SDRAM configuration information
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
- CONFIG_CMD_SCSI) you must configure support for at
+ CONFIG_SCSI) you must configure support for at
least one non-MTD partition type as well.
- IDE Reset method:
consider that a completely unreadable NAND block is bad,
and thus should be skipped silently.
+ CONFIG_SPL_ABORT_ON_RAW_IMAGE
+ When defined, SPL will proceed to another boot method
+ if the image it has loaded does not have a signature.
+
CONFIG_SPL_RELOC_STACK
Adress of the start of the stack SPL will use after
relocation. If unspecified, this is equal to
You only need to set this if address zero isn't writeable
- CONFIG_SYS_MEM_RESERVE_SECURE
+ Only implemented for ARMv8 for now.
If defined, the size of CONFIG_SYS_MEM_RESERVE_SECURE memory
is substracted from total RAM and won't be reported to OS.
This memory can be used as secure memory. A variable
- gd->secure_ram is used to track the location. In systems
+ gd->arch.secure_ram is used to track the location. In systems
the RAM base is not zero, or RAM is divided into banks,
this variable needs to be recalcuated to get the address.
The memory will be freed (or in fact just forgotten) when
U-Boot relocates itself.
- Pre-relocation malloc() is only supported on ARM and sandbox
- at present but is fairly easy to enable for other archs.
-
- CONFIG_SYS_MALLOC_SIMPLE
Provides a simple and small malloc() and calloc() for those
boards which do not use the full malloc in SPL (which is
If defined, don't allow the -f switch to env set override variable
access flags.
-- CONFIG_SYS_GENERIC_BOARD
- This selects the architecture-generic board system instead of the
- architecture-specific board files. It is intended to move boards
- to this new framework over time. Defining this will disable the
- arch/foo/lib/board.c file and use common/board_f.c and
- common/board_r.c instead. To use this option your architecture
- must support it (i.e. must select HAVE_GENERIC_BOARD in arch/Kconfig).
- If you find problems enabling this option on your board please report
- the problem and send patches!
-
- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
This is set by OMAP boards for the max time that reset should
be asserted. See doc/README.omap-reset-time for details on how
other boot loader or by a debugger which performs
these initializations itself.
+- CONFIG_SKIP_LOWLEVEL_INIT_ONLY
+ [ARM926EJ-S only] This allows just the call to lowlevel_init()
+ to be skipped. The normal CPU15 init (such as enabling the
+ instruction cache) is still performed.
+
- CONFIG_SPL_BUILD
Modifies the behaviour of start.S when compiling a loader
that is executed before the actual U-Boot. E.g. when
projects / u-boot / blobdiff