Defines the string to utilize when trying to match PCIe device
tree nodes for the given platform.
+- Generic CPU options:
+ CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
+
+ Defines the endianess of the CPU. Implementation of those
+ values is arch specific.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
May be defined to allow interrupt polling
instead of using asynchronous interrupts
+ CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
+ txfilltuning field in the EHCI controller on reset.
+
- USB Device:
Define the below if you wish to use the USB console.
Once firmware is rebuilt from a serial console issue the
Define this to have a tty type of device available to
talk to the UDC device
+ CONFIG_USBD_HS
+ Define this to enable the high speed support for usb
+ device and usbtty. If this feature is enabled, a routine
+ int is_usbd_high_speed(void)
+ also needs to be defined by the driver to dynamically poll
+ whether the enumeration has succeded at high speed or full
+ speed.
+
CONFIG_SYS_CONSOLE_IS_IN_ENV
Define this if you want stdin, stdout &/or stderr to
be set to usbtty.
- FAT(File Allocation Table) filesystem write function support:
CONFIG_FAT_WRITE
- Support for saving memory data as a file
- in FAT formatted partition
+
+ Define this to enable support for saving memory data as a
+ file in FAT formatted partition.
+
+ This will also enable the command "fatwrite" enabling the
+ user to write files to FAT.
- Keyboard Support:
CONFIG_ISA_KEYBOARD
environment area within the total memory of your DataFlash placed
at the specified address.
+- CONFIG_ENV_IS_IN_REMOTE:
+
+ Define this if you have a remote memory space which you
+ want to use for the local device's environment.
+
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the address and size of the
+ environment area within the remote memory space. The
+ local device can get the environment from remote memory
+ space by SRIO or other links.
+
+BE CAREFUL! For some special cases, the local device can not use
+"saveenv" command. For example, the local device will get the
+environment stored in a remote NOR flash by SRIO link, but it can
+not erase, write this NOR flash by SRIO interface.
+
- CONFIG_ENV_IS_IN_NAND:
Define this if you have a NAND device which you want to use
Specifies that QE/FMAN firmware is located on the primary SPI
device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+- CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+ Specifies that QE/FMAN firmware is located in the remote (master)
+ memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
+ can be mapped from slave TLB->slave LAW->slave SRIO outbound window
+ ->master inbound window->master LAW->the ucode address in master's
+ NOR flash.
Building the Software:
======================
make NAME_config
where "NAME_config" is the name of one of the existing configu-
-rations; see the main Makefile for supported names.
+rations; see boards.cfg for supported names.
Note: for some board special configuration names may exist; check if
additional information is available from the board vendor; for
steps:
1. Add a new configuration option for your board to the toplevel
- "Makefile" and to the "MAKEALL" script, using the existing
- entries as examples. Note that here and at many other places
- boards and other names are listed in alphabetical sort order. Please
- keep this order.
+ "boards.cfg" file, using the existing entries as examples.
+ Follow the instructions there to keep the boards in order.
2. Create a new directory to hold your board specific code. Add any
files you need. In your board directory, you will need at least
the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
run - run commands in an environment variable
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
+bootz - boot zImage from memory
tftpboot- boot image via network using TFTP protocol
and env variables "ipaddr" and "serverip"
(and eventually "gatewayip")
useful when you configure U-Boot to use a real shell (hush)
as command interpreter.
+Booting the Linux zImage:
+-------------------------
+
+On some platforms, it's possible to boot Linux zImage. This is done
+using the "bootz" command. The syntax of "bootz" command is the same
+as the syntax of "bootm" command.
+
+Note, defining the CONFIG_SUPPORT_INITRD_RAW allows user to supply
+kernel with raw initrd images. The syntax is slightly different, the
+address of the initrd must be augmented by it's size, in the following
+format: "<initrd addres>:<initrd size>".
+
Standalone HOWTO:
=================
projects / u-boot / blobdiff