usb: ehci: exynos: Enable non-dt path

[u-boot] / README

diff --git a/README b/README
index 2352e3862bfa81f4ad2bca262cc26529ac008fd7..a620f0a474465bf64b6f3a2bf9a795b9bf5a6316 100644 (file)
--- a/README
+++ b/README
@@ -842,7 +842,8 @@ The following options need to be configured:
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support
                CONFIG_CMD_IMI            iminfo
-               CONFIG_CMD_IMLS           List all found images
+               CONFIG_CMD_IMLS           List all images found in NOR flash
+               CONFIG_CMD_IMLS_NAND      List all images found in NAND flash
                CONFIG_CMD_IMMAP        * IMMR dump support
                CONFIG_CMD_IMPORTENV    * import an environment
                CONFIG_CMD_INI          * import data from an ini file into the env
@@ -859,7 +860,8 @@ The following options need to be configured:
                                          (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
                CONFIG_CMD_MEMINFO      * Display detailed memory information
                CONFIG_CMD_MEMORY         md, mm, nm, mw, cp, cmp, crc, base,
-                                         loop, loopw, mtest
+                                         loop, loopw
+               CONFIG_CMD_MEMTEST        mtest
                CONFIG_CMD_MISC           Misc functions like sleep etc
                CONFIG_CMD_MMC          * MMC memory mapped support
                CONFIG_CMD_MII          * MII utility commands
@@ -876,6 +878,7 @@ The following options need to be configured:
                CONFIG_CMD_READ         * Read raw data from partition
                CONFIG_CMD_REGINFO      * Register dump
                CONFIG_CMD_RUN            run command in env variable
+               CONFIG_CMD_SANDBOX      * sb command to access sandbox features
                CONFIG_CMD_SAVES        * save S record dump
                CONFIG_CMD_SCSI         * SCSI Support
                CONFIG_CMD_SDRAM        * print SDRAM configuration information
@@ -3209,6 +3212,23 @@ Configuration Settings:
        If defined, don't allow the -f switch to env set override variable
        access flags.
 
+- CONFIG_SYS_GENERIC_BOARD
+       This selects the architecture-generic board system instead of the
+       architecture-specific board files. It is intended to move boards
+       to this new framework over time. Defining this will disable the
+       arch/foo/lib/board.c file and use common/board_f.c and
+       common/board_r.c instead. To use this option your architecture
+       must support it (i.e. must define __HAVE_ARCH_GENERIC_BOARD in
+       its config.mk file). If you find problems enabling this option on
+       your board please report the problem and send patches!
+
+- CONFIG_SYS_SYM_OFFSETS
+       This is set by architectures that use offsets for link symbols
+       instead of absolute values. So bss_start is obtained using an
+       offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
+       directly. You should not need to touch this setting.
+
+
 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
 following configurations:
@@ -3810,20 +3830,24 @@ Low Level (hardware related) configuration options:
                that is executed before the actual U-Boot. E.g. when
                compiling a NAND SPL.
 
+- CONFIG_ARCH_MAP_SYSMEM
+               Generally U-Boot (and in particular the md command) uses
+               effective address. It is therefore not necessary to regard
+               U-Boot address as virtual addresses that need to be translated
+               to physical addresses. However, sandbox requires this, since
+               it maintains its own little RAM buffer which contains all
+               addressable memory. This option causes some memory accesses
+               to be mapped through map_sysmem() / unmap_sysmem().
+
 - CONFIG_USE_ARCH_MEMCPY
   CONFIG_USE_ARCH_MEMSET
                If these options are used a optimized version of memcpy/memset will
                be used if available. These functions may be faster under some
                conditions but may increase the binary size.
 
-- CONFIG_X86_NO_RESET_VECTOR
-               If defined, the x86 reset vector code is excluded. You will need
-               to do this when U-Boot is running from Coreboot.
-
-- CONFIG_X86_NO_REAL_MODE
-               If defined, x86 real mode code is omitted. This assumes a
-               32-bit environment where such code is not needed. You will
-               need to do this when U-Boot is running from Coreboot.
+- CONFIG_X86_RESET_VECTOR
+               If defined, the x86 reset vector code is included. This is not
+               needed when U-Boot is running from Coreboot.
 
 
 Freescale QE/FMAN Firmware Support: