#
-# (C) Copyright 2000 - 2002
+# (C) Copyright 2000 - 2004
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
- board Board dependent files
- common Misc architecture independent functions
- cpu CPU specific files
+ - 74xx_7xx Files specific to Motorola MPC74xx and 7xx CPUs
+ - arm720t Files specific to ARM 720 CPUs
+ - arm920t Files specific to ARM 920 CPUs
+ - arm925t Files specific to ARM 925 CPUs
+ - arm926ejs Files specific to ARM 926 CPUs
+ - at91rm9200 Files specific to Atmel AT91RM9200 CPUs
+ - i386 Files specific to i386 CPUs
+ - ixp Files specific to Intel XScale IXP CPUs
+ - mcf52x2 Files specific to Motorola ColdFire MCF52x2 CPUs
+ - mips Files specific to MIPS CPUs
+ - mpc5xx Files specific to Motorola MPC5xx CPUs
+ - mpc5xxx Files specific to Motorola MPC5xxx CPUs
+ - mpc8xx Files specific to Motorola MPC8xx CPUs
+ - mpc824x Files specific to Motorola MPC824x CPUs
+ - mpc8260 Files specific to Motorola MPC8260 CPUs
+ - mpc85xx Files specific to Motorola MPC85xx CPUs
+ - nios Files specific to Altera NIOS CPUs
+ - ppc4xx Files specific to IBM PowerPC 4xx CPUs
+ - pxa Files specific to Intel XScale PXA CPUs
+ - s3c44b0 Files specific to Samsung S3C44B0 CPUs
+ - sa1100 Files specific to Intel StrongARM SA1100 CPUs
- disk Code for disk drive partition handling
- doc Documentation (don't expect too much)
- drivers Commonly used device drivers
- dtt Digital Thermometer and Thermostat drivers
- examples Example code for standalone applications, etc.
- include Header Files
-- disk Harddisk interface code
+- lib_arm Files generic to ARM architecture
+- lib_generic Files generic to all architectures
+- lib_i386 Files generic to i386 architecture
+- lib_m68k Files generic to m68k architecture
+- lib_mips Files generic to MIPS architecture
+- lib_nios Files generic to NIOS architecture
+- lib_ppc Files generic to PowerPC architecture
- net Networking code
-- ppc Files generic to PowerPC architecture
- post Power On Self Test
-- post/arch Symlink to architecture specific Power On Self Test
-- post/arch-ppc PowerPC architecture specific Power On Self Test
-- post/cpu/mpc8260 MPC8260 CPU specific Power On Self Test
-- post/cpu/mpc8xx MPC8xx CPU specific Power On Self Test
- rtc Real Time Clock drivers
- tools Tools to build S-Record or U-Boot images, etc.
-- cpu/74xx_7xx Files specific to Motorola MPC74xx and 7xx CPUs
-- cpu/arm925t Files specific to ARM 925 CPUs
-- cpu/arm926ejs Files specific to ARM 926 CPUs
-- cpu/mpc5xx Files specific to Motorola MPC5xx CPUs
-- cpu/mpc8xx Files specific to Motorola MPC8xx CPUs
-- cpu/mpc824x Files specific to Motorola MPC824x CPUs
-- cpu/mpc8260 Files specific to Motorola MPC8260 CPU
-- cpu/ppc4xx Files specific to IBM 4xx CPUs
-
-
-- board/LEOX/ Files specific to boards manufactured by The LEOX team
-- board/LEOX/elpt860 Files specific to ELPT860 boards
-- board/RPXClassic
- Files specific to RPXClassic boards
-- board/RPXlite Files specific to RPXlite boards
-- board/at91rm9200dk Files specific to AT91RM9200DK boards
-- board/c2mon Files specific to c2mon boards
-- board/cmi Files specific to cmi boards
-- board/cogent Files specific to Cogent boards
- (need further configuration)
- Files specific to CPCIISER4 boards
-- board/cpu86 Files specific to CPU86 boards
-- board/cray/ Files specific to boards manufactured by Cray
-- board/cray/L1 Files specific to L1 boards
-- board/cu824 Files specific to CU824 boards
-- board/ebony Files specific to IBM Ebony board
-- board/eric Files specific to ERIC boards
-- board/esd/ Files specific to boards manufactured by ESD
-- board/esd/adciop Files specific to ADCIOP boards
-- board/esd/ar405 Files specific to AR405 boards
-- board/esd/canbt Files specific to CANBT boards
-- board/esd/cpci405 Files specific to CPCI405 boards
-- board/esd/cpciiser4 Files specific to CPCIISER4 boards
-- board/esd/common Common files for ESD boards
-- board/esd/dasa_sim Files specific to DASA_SIM boards
-- board/esd/du405 Files specific to DU405 boards
-- board/esd/ocrtc Files specific to OCRTC boards
-- board/esd/pci405 Files specific to PCI405 boards
-- board/esteem192e
- Files specific to ESTEEM192E boards
-- board/etx094 Files specific to ETX_094 boards
-- board/evb64260
- Files specific to EVB64260 boards
-- board/fads Files specific to FADS boards
-- board/flagadm Files specific to FLAGADM boards
-- board/gen860t Files specific to GEN860T and GEN860T_SC boards
-- board/genietv Files specific to GENIETV boards
-- board/gth Files specific to GTH boards
-- board/hermes Files specific to HERMES boards
-- board/hymod Files specific to HYMOD boards
-- board/icu862 Files specific to ICU862 boards
-- board/ip860 Files specific to IP860 boards
-- board/iphase4539
- Files specific to Interphase4539 boards
-- board/ivm Files specific to IVMS8/IVML24 boards
-- board/lantec Files specific to LANTEC boards
-- board/lwmon Files specific to LWMON boards
-- board/mbx8xx Files specific to MBX boards
-- board/mpc8260ads
- Files specific to MPC8260ADS and PQ2FADS-ZU boards
-- board/mpl/ Files specific to boards manufactured by MPL
-- board/mpl/common Common files for MPL boards
-- board/mpl/pip405 Files specific to PIP405 boards
-- board/mpl/mip405 Files specific to MIP405 boards
-- board/mpl/vcma9 Files specific to VCMA9 boards
-- board/musenki Files specific to MUSEKNI boards
-- board/mvs1 Files specific to MVS1 boards
-- board/nx823 Files specific to NX823 boards
-- board/oxc Files specific to OXC boards
-- board/omap1510inn
- Files specific to OMAP 1510 Innovator boards
-- board/omap1610inn
- Files specific to OMAP 1610 Innovator boards
-- board/pcippc2 Files specific to PCIPPC2/PCIPPC6 boards
-- board/pm826 Files specific to PM826 boards
-- board/ppmc8260
- Files specific to PPMC8260 boards
-- board/rpxsuper
- Files specific to RPXsuper boards
-- board/rsdproto
- Files specific to RSDproto boards
-- board/sandpoint
- Files specific to Sandpoint boards
-- board/sbc8260 Files specific to SBC8260 boards
-- board/sacsng Files specific to SACSng boards
-- board/siemens Files specific to boards manufactured by Siemens AG
-- board/siemens/CCM Files specific to CCM boards
-- board/siemens/IAD210 Files specific to IAD210 boards
-- board/siemens/SCM Files specific to SCM boards
-- board/siemens/pcu_e Files specific to PCU_E boards
-- board/sixnet Files specific to SIXNET boards
-- board/spd8xx Files specific to SPD8xxTS boards
-- board/tqm8260 Files specific to TQM8260 boards
-- board/tqm8xx Files specific to TQM8xxL boards
-- board/w7o Files specific to W7O boards
-- board/walnut405
- Files specific to Walnut405 boards
-- board/westel/ Files specific to boards manufactured by Westel Wireless
-- board/westel/amx860 Files specific to AMX860 boards
-- board/utx8245 Files specific to UTX8245 boards
-
Software Configuration:
=======================
CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
or CONFIG_MPC5xx
or CONFIG_MPC824X, CONFIG_MPC8260
+ or CONFIG_MPC85xx
or CONFIG_IOP480
or CONFIG_405GP
or CONFIG_405EP
CONFIG_ARM7
CONFIG_PXA250
+ MicroBlaze based CPUs:
+ ----------------------
+ CONFIG_MICROBLZE
+
- Board Type: Define exactly one of
PowerPC based boards:
---------------------
- CONFIG_ADCIOP, CONFIG_ICU862 CONFIG_RPXsuper,
- CONFIG_ADS860, CONFIG_IP860, CONFIG_SM850,
- CONFIG_AMX860, CONFIG_IPHASE4539, CONFIG_SPD823TS,
- CONFIG_AR405, CONFIG_IVML24, CONFIG_SXNI855T,
- CONFIG_BAB7xx, CONFIG_IVML24_128, CONFIG_Sandpoint8240,
- CONFIG_CANBT, CONFIG_IVML24_256, CONFIG_Sandpoint8245,
- CONFIG_CCM, CONFIG_IVMS8, CONFIG_TQM823L,
- CONFIG_CPCI405, CONFIG_IVMS8_128, CONFIG_TQM850L,
- CONFIG_CPCI4052, CONFIG_IVMS8_256, CONFIG_TQM855L,
- CONFIG_CPCIISER4, CONFIG_LANTEC, CONFIG_TQM860L,
- CONFIG_CPU86, CONFIG_MBX, CONFIG_TQM8260,
- CONFIG_CRAYL1, CONFIG_MBX860T, CONFIG_TTTech,
- CONFIG_CU824, CONFIG_MHPC, CONFIG_UTX8245,
- CONFIG_DASA_SIM, CONFIG_MIP405, CONFIG_W7OLMC,
- CONFIG_DU405, CONFIG_MOUSSE, CONFIG_W7OLMG,
- CONFIG_ELPPC, CONFIG_MPC8260ADS, CONFIG_WALNUT405,
- CONFIG_ERIC, CONFIG_MUSENKI, CONFIG_ZUMA,
- CONFIG_ESTEEM192E, CONFIG_MVS1, CONFIG_c2mon,
- CONFIG_ETX094, CONFIG_NX823, CONFIG_cogent_mpc8260,
- CONFIG_EVB64260, CONFIG_OCRTC, CONFIG_cogent_mpc8xx,
- CONFIG_FADS823, CONFIG_ORSG, CONFIG_ep8260,
- CONFIG_FADS850SAR, CONFIG_OXC, CONFIG_gw8260,
- CONFIG_FADS860T, CONFIG_PCI405, CONFIG_hermes,
- CONFIG_FLAGADM, CONFIG_PCIPPC2, CONFIG_hymod,
- CONFIG_FPS850L, CONFIG_PCIPPC6, CONFIG_lwmon,
- CONFIG_GEN860T, CONFIG_PIP405, CONFIG_pcu_e,
- CONFIG_GENIETV, CONFIG_PM826, CONFIG_ppmc8260,
- CONFIG_GTH, CONFIG_RPXClassic, CONFIG_rsdproto,
- CONFIG_IAD210, CONFIG_RPXlite, CONFIG_sbc8260,
- CONFIG_EBONY, CONFIG_sacsng, CONFIG_FPS860L,
- CONFIG_V37, CONFIG_ELPT860, CONFIG_CMI,
- CONFIG_NETVIA, CONFIG_RBC823
+ CONFIG_ADCIOP, CONFIG_ADS860, CONFIG_AMX860,
+ CONFIG_AR405, CONFIG_BAB7xx, CONFIG_c2mon,
+ CONFIG_CANBT, CONFIG_CCM, CONFIG_CMI,
+ CONFIG_cogent_mpc8260, CONFIG_cogent_mpc8xx, CONFIG_CPCI405,
+ CONFIG_CPCI4052, CONFIG_CPCIISER4, CONFIG_CPU86,
+ CONFIG_CRAYL1, CONFIG_CU824, CONFIG_DASA_SIM,
+ CONFIG_DB64360, CONFIG_DB64460, CONFIG_DU405,
+ CONFIG_DUET_ADS, CONFIG_EBONY, CONFIG_ELPPC,
+ CONFIG_ELPT860, CONFIG_ep8260, CONFIG_ERIC,
+ CONFIG_ESTEEM192E, CONFIG_ETX094, CONFIG_EVB64260,
+ CONFIG_FADS823, CONFIG_FADS850SAR, CONFIG_FADS860T,
+ CONFIG_FLAGADM, CONFIG_FPS850L, CONFIG_FPS860L,
+ CONFIG_GEN860T, CONFIG_GENIETV, CONFIG_GTH,
+ CONFIG_gw8260, CONFIG_hermes, CONFIG_hymod,
+ CONFIG_IAD210, CONFIG_ICU862, CONFIG_IP860,
+ CONFIG_IPHASE4539, CONFIG_IVML24, CONFIG_IVML24_128,
+ CONFIG_IVML24_256, CONFIG_IVMS8, CONFIG_IVMS8_128,
+ CONFIG_IVMS8_256, CONFIG_JSE, CONFIG_LANTEC,
+ CONFIG_lwmon, CONFIG_MBX, CONFIG_MBX860T,
+ CONFIG_MHPC, CONFIG_MIP405, CONFIG_MOUSSE,
+ CONFIG_MPC8260ADS, CONFIG_MPC8540ADS, CONFIG_MPC8560ADS,
+ CONFIG_MUSENKI, CONFIG_MVS1, CONFIG_NETPHONE,
+ CONFIG_NETTA, CONFIG_NETVIA, CONFIG_NX823,
+ CONFIG_OCRTC, CONFIG_ORSG, CONFIG_OXC,
+ CONFIG_PCI405, CONFIG_PCIPPC2, CONFIG_PCIPPC6,
+ CONFIG_pcu_e, CONFIG_PIP405, CONFIG_PM826,
+ CONFIG_ppmc8260, CONFIG_QS823, CONFIG_QS850,
+ CONFIG_QS860T, CONFIG_RBC823, CONFIG_RPXClassic,
+ CONFIG_RPXlite, CONFIG_RPXsuper, CONFIG_rsdproto,
+ CONFIG_sacsng, CONFIG_Sandpoint8240, CONFIG_Sandpoint8245,
+ CONFIG_sbc8260, CONFIG_SM850, CONFIG_SPD823TS,
+ CONFIG_STXGP3, CONFIG_SXNI855T, CONFIG_TQM823L,
+ CONFIG_TQM8260, CONFIG_TQM850L, CONFIG_TQM855L,
+ CONFIG_TQM860L, CONFIG_TTTech, CONFIG_UTX8245,
+ CONFIG_V37, CONFIG_W7OLMC, CONFIG_W7OLMG,
+ CONFIG_WALNUT405, CONFIG_ZPC1900, CONFIG_ZUMA,
ARM based boards:
-----------------
- CONFIG_HHP_CRADLE, CONFIG_DNP1110, CONFIG_EP7312,
- CONFIG_IMPA7, CONFIG_LART, CONFIG_LUBBOCK,
- CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610
- CONFIG_SHANNON, CONFIG_SMDK2400, CONFIG_SMDK2410,
- CONFIG_TRAB, CONFIG_VCMA9, CONFIG_AT91RM9200DK
+ CONFIG_AT91RM9200DK, CONFIG_DNP1110, CONFIG_EP7312,
+ CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE, CONFIG_IMPA7,
+ CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610, CONFIG_LART,
+ CONFIG_LUBBOCK, CONFIG_SHANNON, CONFIG_SMDK2400,
+ CONFIG_SMDK2410, CONFIG_TRAB, CONFIG_VCMA9,
+
+ MicroBlaze based boards:
+ ------------------------
+
+ CONFIG_SUZAKU
- CPU Module Type: (if CONFIG_COGENT is defined)
CONFIG_ADSTYPE
Possible values are:
CFG_8260ADS - original MPC8260ADS
- CFG_8266ADS - MPC8266ADS (untested)
- CFG_PQ2FADS - PQ2FADS-ZU
-
+ CFG_8266ADS - MPC8266ADS
+ CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
+ CFG_8272ADS - MPC8272ADS
- MPC824X Family Member (if CONFIG_MPC824X is defined)
- Define exactly one of
- CONFIG_MPC8240, CONFIG_MPC8245
+ Define exactly one of
+ CONFIG_MPC8240, CONFIG_MPC8245
-- 8xx CPU Options: (if using an 8xx cpu)
+- 8xx CPU Options: (if using an MPC8xx cpu)
Define one or more of
- CONFIG_8xx_GCLK_FREQ - if get_gclk_freq() can not work e.g.
- no 32KHz reference PIT/RTC clock
-
-- Clock Interface:
+ CONFIG_8xx_GCLK_FREQ - if get_gclk_freq() cannot work
+ e.g. if there is no 32KHz
+ reference PIT/RTC clock
+
+- 859/866 CPU options: (if using a MPC859 or MPC866 CPU):
+ CFG_866_OSCCLK
+ CFG_866_CPUCLK_MIN
+ CFG_866_CPUCLK_MAX
+ CFG_866_CPUCLK_DEFAULT
+ See doc/README.MPC866
+
+ CFG_MEASURE_CPUCLK
+
+ Define this to measure the actual CPU clock instead
+ of relying on the correctness of the configured
+ values. Mostly useful for board bringup to make sure
+ the PLL is locked at the intended frequency. Note
+ that this requires a (stable) reference clock (32 kHz
+ RTC clock),
+
+- Linux Kernel Interface:
CONFIG_CLOCKS_IN_MHZ
U-Boot stores all clock information in Hz
"clocks_in_mhz" can be defined so that U-Boot
converts clock data to MHZ before passing it to the
Linux kernel.
-
When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
"clocks_in_mhz=1" is automatically included in the
default environment.
+ CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
+
+ When transfering memsize parameter to linux, some versions
+ expect it to be in bytes, others in MB.
+ Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
+
- Console Interface:
Depending on board, define exactly one serial port
(like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
bit-blit (cf. smiLynxEM)
VIDEO_VISIBLE_COLS visible pixel columns
(cols=pitch)
- VIDEO_VISIBLE_ROWS visible pixel rows
- VIDEO_PIXEL_SIZE bytes per pixel
+ VIDEO_VISIBLE_ROWS visible pixel rows
+ VIDEO_PIXEL_SIZE bytes per pixel
VIDEO_DATA_FORMAT graphic data format
(0-5, cf. cfb_console.c)
- VIDEO_FB_ADRS framebuffer address
+ VIDEO_FB_ADRS framebuffer address
VIDEO_KBD_INIT_FCT keyboard int fct
(i.e. i8042_kbd_init())
VIDEO_TSTC_FCT test char fct
default i/o. Serial console can be forced with
environment 'console=serial'.
+ When CONFIG_SILENT_CONSOLE is defined, all console
+ messages (by U-Boot and Linux!) can be silenced with
+ the "silent" environment variable. See
+ doc/README.silent for more information.
+
- Console Baudrate:
CONFIG_BAUDRATE - in bps
Select one of the baudrates listed in
CFG_BAUDRATE_TABLE, see below.
+ CFG_BRGCLK_PRESCALE, baudrate prescale
- Interrupt driven serial port input:
CONFIG_SERIAL_SOFTWARE_FIFO
(RTS/CTS) and UART's built-in FIFO. Set the number of
bytes the interrupt driven input buffer should have.
- Set to 0 to disable this feature (this is the default).
- This will also disable hardware handshake.
+ Leave undefined to disable this feature, including
+ disable the buffer and hardware handshake.
- Console UART Number:
CONFIG_UART1_CONSOLE
CFG_CMD_AUTOSCRIPT Autoscript Support
CFG_CMD_BDI bdinfo
CFG_CMD_BEDBUG Include BedBug Debugger
- CFG_CMD_BMP * BMP support
+ CFG_CMD_BMP * BMP support
CFG_CMD_BOOTD bootd
CFG_CMD_CACHE icache, dcache
CFG_CMD_CONSOLE coninfo
CFG_CMD_DATE * support for RTC, date/time...
CFG_CMD_DHCP DHCP support
- CFG_CMD_DIAG * Diagnostics
- CFG_CMD_DOC * Disk-On-Chip Support
- CFG_CMD_DTT Digital Therm and Thermostat
+ CFG_CMD_DIAG * Diagnostics
+ CFG_CMD_DOC * Disk-On-Chip Support
+ CFG_CMD_DTT Digital Therm and Thermostat
CFG_CMD_ECHO * echo arguments
CFG_CMD_EEPROM * EEPROM read/write support
CFG_CMD_ELF bootelf, bootvx
CFG_CMD_FDOS * Dos diskette Support
CFG_CMD_FLASH flinfo, erase, protect
CFG_CMD_FPGA FPGA device initialization support
- CFG_CMD_HWFLOW * RTS/CTS hw flow control
+ CFG_CMD_HWFLOW * RTS/CTS hw flow control
CFG_CMD_I2C * I2C serial bus support
CFG_CMD_IDE * IDE harddisk support
CFG_CMD_IMI iminfo
- CFG_CMD_IMLS List all found images
+ CFG_CMD_IMLS List all found images
CFG_CMD_IMMAP * IMMR dump support
CFG_CMD_IRQ * irqinfo
- CFG_CMD_JFFS2 * JFFS2 Support
+ CFG_CMD_ITEST * Integer/string test of 2 values
+ CFG_CMD_JFFS2 * JFFS2 Support
CFG_CMD_KGDB * kgdb
CFG_CMD_LOADB loadb
CFG_CMD_LOADS loads
CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
loop, mtest
- CFG_CMD_MISC Misc functions like sleep etc
+ CFG_CMD_MISC Misc functions like sleep etc
CFG_CMD_MMC MMC memory mapped support
CFG_CMD_MII MII utility commands
- CFG_CMD_NAND * NAND support
+ CFG_CMD_NAND * NAND support
CFG_CMD_NET bootp, tftpboot, rarpboot
CFG_CMD_PCI * pciinfo
CFG_CMD_PCMCIA * PCMCIA support
- CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
- CFG_CMD_PORTIO Port I/O
+ CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
+ CFG_CMD_PORTIO * Port I/O
CFG_CMD_REGINFO * Register dump
CFG_CMD_RUN run command in env variable
- CFG_CMD_SAVES save S record dump
+ CFG_CMD_SAVES save S record dump
CFG_CMD_SCSI * SCSI Support
- CFG_CMD_SDRAM * print SDRAM configuration information
+ CFG_CMD_SDRAM * print SDRAM configuration information
CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
CFG_CMD_SPI * SPI serial bus support
CFG_CMD_USB * USB support
- CFG_CMD_VFD * VFD support (TRAB)
+ CFG_CMD_VFD * VFD support (TRAB)
CFG_CMD_BSP * Board SPecific functions
+ CFG_CMD_CDP * Cisco Discover Protocol support
-----------------------------------------------
CFG_CMD_ALL all
one partition type as well.
- IDE Reset method:
- CONFIG_IDE_RESET_ROUTINE
+ CONFIG_IDE_RESET_ROUTINE - this is defined in several
+ board configurations files but used nowhere!
- Set this to define that instead of a reset Pin, the
- routine ide_set_reset(int idereset) will be used.
+ CONFIG_IDE_RESET - is this is defined, IDE Reset will
+ be performed by calling the function
+ ide_set_reset(int reset)
+ which has to be defined in a board specific file
- ATAPI Support:
CONFIG_ATAPI
Set this to enable ATAPI support.
+- LBA48 Support
+ CONFIG_LBA48
+
+ Set this to enable support for disks larger than 137GB
+ Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
+ Whithout these , LBA48 support uses 32bit variables and will 'only'
+ support disks up to 2.1TB.
+
+ CFG_64BIT_LBA:
+ When enabled, makes the IDE subsystem use 64bit sector addresses.
+ Default is 32bit.
+
- SCSI Support:
At the moment only there is only support for the
SYM53C8XX SCSI controller; define
- USB Support:
At the moment only the UHCI host controller is
- supported (PIP405, MIP405); define
+ supported (PIP405, MIP405, MPC5200); define
CONFIG_USB_UHCI to enable it.
define CONFIG_USB_KEYBOARD to enable the USB Keyboard
end define CONFIG_USB_STORAGE to enable the USB
Note:
Supported are USB Keyboards and USB Floppy drives
(TEAC FD-05PUB).
+ MPC5200 USB requires additional defines:
+ CONFIG_USB_CLOCK
+ for 528 MHz Clock: 0x0001bbbb
+ CONFIG_USB_CONFIG
+ for differential drivers: 0x00001000
+ for single ended drivers: 0x00005000
+
- MMC Support:
The MMC controller on the Intel PXA is supported. To
Enable Chips & Technologies 69000 Video chip
CONFIG_VIDEO_SMI_LYNXEM
- Enable Silicon Motion SMI 712/710/810 Video chip
- Videomode are selected via environment 'videomode' with
- standard LiLo mode numbers.
- Following modes are supported (* is default):
-
- 800x600 1024x768 1280x1024
- 256 (8bit) 303* 305 307
- 65536 (16bit) 314 317 31a
- 16,7 Mill (24bit) 315 318 31b
+ Enable Silicon Motion SMI 712/710/810 Video chip. The
+ video output is selected via environment 'videoout'
+ (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
+ assumed.
+
+ For the CT69000 and SMI_LYNXEM drivers, videomode is
+ selected via environment 'videomode'. Two diferent ways
+ are possible:
+ - "videomode=num" 'num' is a standard LiLo mode numbers.
+ Following standard modes are supported (* is default):
+
+ Colors 640x480 800x600 1024x768 1152x864 1280x1024
+ -------------+---------------------------------------------
+ 8 bits | 0x301* 0x303 0x305 0x161 0x307
+ 15 bits | 0x310 0x313 0x316 0x162 0x319
+ 16 bits | 0x311 0x314 0x317 0x163 0x31A
+ 24 bits | 0x312 0x315 0x318 ? 0x31B
+ -------------+---------------------------------------------
(i.e. setenv videomode 317; saveenv; reset;)
+ - "videomode=bootargs" all the video parameters are parsed
+ from the bootargs. (See drivers/videomodes.c)
+
+
CONFIG_VIDEO_SED13806
Enable Epson SED13806 driver. This driver supports 8bpp
and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
display); also select one of the supported displays
by defining one of these:
- CONFIG_NEC_NL6648AC33:
+ CONFIG_NEC_NL6448AC33:
- NEC NL6648AC33-18. Active, color, single scan.
+ NEC NL6448AC33-18. Active, color, single scan.
- CONFIG_NEC_NL6648BC20
+ CONFIG_NEC_NL6448BC20
- NEC NL6648BC20-08. 6.5", 640x480.
+ NEC NL6448BC20-08. 6.5", 640x480.
+ Active, color, single scan.
+
+ CONFIG_NEC_NL6448BC33_54
+
+ NEC NL6448BC33-54. 10.4", 640x480.
Active, color, single scan.
CONFIG_SHARP_16x9
images is included. If not, only uncompressed and gzip
compressed images are supported.
- NOTE: the bzip2 algorithm requires a lot of RAM, so
- the malloc area (as defined by CFG_MALLOC_LEN) should
- be at least 4MB.
+ NOTE: the bzip2 algorithm requires a lot of RAM, so
+ the malloc area (as defined by CFG_MALLOC_LEN) should
+ be at least 4MB.
- Ethernet address:
CONFIG_ETHADDR
environment variable is passed as option 12 to
the DHCP server.
+ - CDP Options:
+ CONFIG_CDP_DEVICE_ID
+
+ The device id used in CDP trigger frames.
+
+ CONFIG_CDP_DEVICE_ID_PREFIX
+
+ A two character string which is prefixed to the MAC address
+ of the device.
+
+ CONFIG_CDP_PORT_ID
+
+ A printf format string which contains the ascii name of
+ the port. Normally is set to "eth%d" which sets
+ eth0 for the first ethernet, eth1 for the second etc.
+
+ CONFIG_CDP_CAPABILITIES
+
+ A 32bit integer which indicates the device capabilities;
+ 0x00000010 for a normal host which does not forwards.
+
+ CONFIG_CDP_VERSION
+
+ An ascii string containing the version of the software.
+
+ CONFIG_CDP_PLATFORM
+
+ An ascii string containing the name of the platform.
+
+ CONFIG_CDP_TRIGGER
+
+ A 32bit integer sent on the trigger.
+
+ CONFIG_CDP_POWER_CONSUMPTION
+
+ A 16bit integer containing the power consumption of the
+ device in .1 of milliwatts.
+
+ CONFIG_CDP_APPLIANCE_VLAN_TYPE
+
+ A byte containing the id of the VLAN.
+
- Status LED: CONFIG_STATUS_LED
Several configurations allow to display the current
clock chips. See common/cmd_i2c.c for a description of the
command line interface.
- CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
+ CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
CONFIG_SOFT_I2C configures u-boot to use a software (aka
bit-banging) driver instead of CPM or similar hardware
(Optional). Any commands necessary to enable the I2C
controller or configure ports.
- eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
+ eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
I2C_PORT
eg: #define I2C_SDA(bit) \
if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
I2C_SCL(bit)
eg: #define I2C_SCL(bit) \
if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
I2C_DELAY
CONFIG_FPGA
- Used to specify the types of FPGA devices. For
- example,
- #define CONFIG_FPGA CFG_XILINX_VIRTEX2
-
- CFG_FPGA_PROG_FEEDBACK
-
- Enable printing of hash marks during FPGA
- configuration.
-
- CFG_FPGA_CHECK_BUSY
-
- Enable checks on FPGA configuration interface busy
- status by the configuration function. This option
- will require a board or device specific function to
- be written.
-
- CONFIG_FPGA_DELAY
-
- If defined, a function that provides delays in the
- FPGA configuration driver.
-
- CFG_FPGA_CHECK_CTRLC
-
- Allow Control-C to interrupt FPGA configuration
-
- CFG_FPGA_CHECK_ERROR
-
- Check for configuration errors during FPGA bitfile
- loading. For example, abort during Virtex II
- configuration if the INIT_B line goes low (which
- indicated a CRC error).
-
- CFG_FPGA_WAIT_INIT
-
- Maximum time to wait for the INIT_B line to deassert
- after PROB_B has been deasserted during a Virtex II
- FPGA configuration sequence. The default time is 500 mS.
-
- CFG_FPGA_WAIT_BUSY
-
- Maximum time to wait for BUSY to deassert during
- Virtex II FPGA configuration. The default is 5 mS.
-
- CFG_FPGA_WAIT_CONFIG
-
- Time to wait after FPGA configuration. The default is
- 200 mS.
-
-- FPGA Support: CONFIG_FPGA_COUNT
-
- Specify the number of FPGA devices to support.
-
- CONFIG_FPGA
-
Used to specify the types of FPGA devices. For example,
#define CONFIG_FPGA CFG_XILINX_VIRTEX2
default value of 5 is used.
- Command Interpreter:
+ CFG_AUTO_COMPLETE
+
+ Enable auto completion of commands using TAB.
+
CFG_HUSH_PARSER
Define this variable to enable the "hush" shell (from
of the backslashes before semicolons and special
symbols.
-- Default Environment
+- Default Environment:
CONFIG_EXTRA_ENV_SETTINGS
Define this to contain any number of null terminated
the environment like the autoscript function or the
boot command first.
-- DataFlash Support
+- DataFlash Support:
CONFIG_HAS_DATAFLASH
Defining this option enables DataFlash features and
allows to read/write in Dataflash via the standard
commands cp, md...
-- Show boot progress
+- SystemACE Support:
+ CONFIG_SYSTEMACE
+
+ Adding this option adds support for Xilinx SystemACE
+ chips attached via some sort of local bus. The address
+ of the chip must alsh be defined in the
+ CFG_SYSTEMACE_BASE macro. For example:
+
+ #define CONFIG_SYSTEMACE
+ #define CFG_SYSTEMACE_BASE 0xf0000000
+
+ When SystemACE support is added, the "ace" device type
+ becomes available to the fat commands, i.e. fatls.
+
+- Show boot progress:
CONFIG_SHOW_BOOT_PROGRESS
Defining this option allows to add some board-
Arg Where When
1 common/cmd_bootm.c before attempting to boot an image
- -1 common/cmd_bootm.c Image header has bad magic number
+ -1 common/cmd_bootm.c Image header has bad magic number
2 common/cmd_bootm.c Image header has correct magic number
- -2 common/cmd_bootm.c Image header has bad checksum
+ -2 common/cmd_bootm.c Image header has bad checksum
3 common/cmd_bootm.c Image header has correct checksum
- -3 common/cmd_bootm.c Image data has bad checksum
+ -3 common/cmd_bootm.c Image data has bad checksum
4 common/cmd_bootm.c Image data has correct checksum
-4 common/cmd_bootm.c Image is for unsupported architecture
5 common/cmd_bootm.c Architecture check OK
8 common/cmd_bootm.c Image Type check OK
-9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
9 common/cmd_bootm.c Start initial ramdisk verification
- -10 common/cmd_bootm.c Ramdisk header has bad magic number
- -11 common/cmd_bootm.c Ramdisk header has bad checksum
+ -10 common/cmd_bootm.c Ramdisk header has bad magic number
+ -11 common/cmd_bootm.c Ramdisk header has bad checksum
10 common/cmd_bootm.c Ramdisk header is OK
- -12 common/cmd_bootm.c Ramdisk data has bad checksum
+ -12 common/cmd_bootm.c Ramdisk data has bad checksum
11 common/cmd_bootm.c Ramdisk data has correct checksum
12 common/cmd_bootm.c Ramdisk verification complete, start loading
-13 common/cmd_bootm.c Wrong Image Type (not PPC Linux Ramdisk)
14 common/cmd_bootm.c No initial ramdisk, no multifile, continue.
15 common/cmd_bootm.c All preparation done, transferring control to OS
+ -30 lib_ppc/board.c Fatal error, hang the system
+ -31 post/post.c POST test failed, detected by post_output_backlog()
+ -32 post/post.c POST test failed, detected by post_run_single()
+
-1 common/cmd_doc.c Bad usage of "doc" command
-1 common/cmd_doc.c No boot device
-1 common/cmd_doc.c Unknown Chip ID on boot device
-1 common/cmd_nand.c Read Error on boot device
-1 common/cmd_nand.c Image header has bad magic number
- -1 common/env_common.c Environment has a bad CRC, using default
+ -1 common/env_common.c Environment has a bad CRC, using default
Modem Support:
Enables debugging stuff (char screen[1024], dbg())
for modem support. Useful only with BDI2000.
+- Interrupt support (PPC):
+
+ There are common interrupt_init() and timer_interrupt()
+ for all PPC archs. interrupt_init() calls interrupt_init_cpu()
+ for cpu specific initialization. interrupt_init_cpu()
+ should set decrementer_count to appropriate value. If
+ cpu resets decrementer automatically after interrupt
+ (ppc4xx) it should set decrementer_count to zero.
+ timer_interrupt() calls timer_interrupt_cpu() for cpu
+ specific handling. If board has watchdog / status_led
+ / other_activity_monitor it works automatically from
+ general timer_interrupt().
+
- General:
In the target system modem support is enabled when a
- CFG_FLASH_CFI:
Define if the flash driver uses extra elements in the
- common flash structure for storing flash geometry
+ common flash structure for storing flash geometry.
+
+- CFG_FLASH_CFI_DRIVER
+ This option also enables the building of the cfi_flash driver
+ in the drivers directory
- CFG_RX_ETH_BUFFER:
Defines the number of ethernet receive buffers. On some
- CFG_EEPROM_PAGE_WRITE_DELAY_MS:
If defined, the number of milliseconds to delay between
- page writes. The default is zero milliseconds.
+ page writes. The default is zero milliseconds.
- CFG_I2C_EEPROM_ADDR_LEN:
The length in bytes of the EEPROM memory array address. Note
that this is NOT the chip address length!
+ - CFG_I2C_EEPROM_ADDR_OVERFLOW:
+ EEPROM chips that implement "address overflow" are ones
+ like Catalyst 24WC04/08/16 which has 9/10/11 bits of
+ address and the extra bits end up in the "chip address" bit
+ slots. This makes a 24WC08 (1Kbyte) chip look like four 256
+ byte chips.
+
+ Note that we consider the length of the address field to
+ still be one byte because the extra address bits are hidden
+ in the chip address.
+
- CFG_EEPROM_SIZE:
The size in bytes of the EEPROM device.
+- CFG_ENV_IS_IN_DATAFLASH:
+
+ Define this if you have a DataFlash memory device which you
+ want to use for the environment.
+
+ - CFG_ENV_OFFSET:
+ - CFG_ENV_ADDR:
+ - CFG_ENV_SIZE:
+
+ These three #defines specify the offset and size of the
+ environment area within the total memory of your DataFlash placed
+ at the specified address.
+
+
- CFG_SPI_INIT_OFFSET
Defines offset to the initial SPI buffer area in DPRAM. The
the default environment is used; a new CRC is computed as soon as you
use the "saveenv" command to store a valid environment.
+- CFG_FAULT_ECHO_LINK_DOWN:
+ Echo the inverted Ethernet link state to the fault LED.
+
+ Note: If this option is active, then CFG_FAULT_MII_ADDR
+ also needs to be defined.
+
+- CFG_FAULT_MII_ADDR:
+ MII address of the PHY to check for the Ethernet link state.
+
+- CFG_64BIT_VSPRINTF:
+ Makes vsprintf (and all *printf functions) support printing
+ of 64bit values by using the L quantifier
+
+- CFG_64BIT_STRTOUL:
+ Adds simple_strtoull that returns a 64bit value
Low Level (hardware related) configuration options:
---------------------------------------------------
- CFG_DEFAULT_IMMR:
Default address of the IMMR after system reset.
- Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
- and RPXsuper) to be able to adjust the position of
- the IMMR register after a reset.
+ Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
+ and RPXsuper) to be able to adjust the position of
+ the IMMR register after a reset.
- Floppy Disk Support:
CFG_FDC_DRIVE_NUMBER
CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
+- CONFIG_ETHER_ON_FEC[12]
+ Define to enable FEC[12] on a 8xx series processor.
+
+- CONFIG_FEC[12]_PHY
+ Define to the hardcoded PHY address which corresponds
+ to the given FEC; i. e.
+ #define CONFIG_FEC1_PHY 4
+ means that the PHY with address 4 is connected to FEC1
+
+ When set to -1, means to probe for first available.
+
+- CONFIG_FEC[12]_PHY_NORXERR
+ The PHY does not have a RXERR line (RMII only).
+ (so program the FEC to ignore it).
+
+- CONFIG_RMII
+ Enable RMII mode for all FECs.
+ Note that this is a global option, we can't
+ have one FEC in standard MII mode and another in RMII mode.
+
+- CONFIG_CRC32_VERIFY
+ Add a verify option to the crc32 command.
+ The syntax is:
+
+ => crc32 -v <address> <count> <crc32>
+
+ Where address/count indicate a memory area
+ and crc32 is the correct crc32 which the
+ area should have.
+
Building the Software:
======================
CROSS_COMPILE = ppc_4xx-
-U-Boot is intended to be simple to build. After installing the
+U-Boot is intended to be simple to build. After installing the
sources you must configure U-Boot for one specific board type. This
is done by typing:
where "NAME_config" is the name of one of the existing
configurations; the following names are supported:
- ADCIOP_config GTH_config TQM850L_config
- ADS860_config IP860_config TQM855L_config
- AR405_config IVML24_config TQM860L_config
- CANBT_config IVMS8_config WALNUT405_config
- CPCI405_config LANTEC_config cogent_common_config
- CPCIISER4_config MBX_config cogent_mpc8260_config
- CU824_config MBX860T_config cogent_mpc8xx_config
- ESTEEM192E_config RPXlite_config hermes_config
- ETX094_config RPXsuper_config hymod_config
- FADS823_config SM850_config lwmon_config
- FADS850SAR_config SPD823TS_config pcu_e_config
- FADS860T_config SXNI855T_config rsdproto_config
- FPS850L_config Sandpoint8240_config sbc8260_config
- GENIETV_config TQM823L_config PIP405_config
- GEN860T_config EBONY_config FPS860L_config
- ELPT860_config cmi_mpc5xx_config NETVIA_config
- at91rm9200dk_config omap1510inn_config MPC8260ADS_config
- omap1610inn_config
-Note: for some board special configuration names may exist; check if
- additional information is available from the board vendor; for
- instance, the TQM8xxL systems run normally at 50 MHz and use a
- SCC for 10baseT ethernet; there are also systems with 80 MHz
- CPU clock, and an optional Fast Ethernet module is available
- for CPU's with FEC. You can select such additional "features"
- when chosing the configuration, i. e.
-
- make TQM860L_config
- - will configure for a plain TQM860L, i. e. 50MHz, no FEC
-
- make TQM860L_FEC_config
- - will configure for a TQM860L at 50MHz with FEC for ethernet
-
- make TQM860L_80MHz_config
- - will configure for a TQM860L at 80 MHz, with normal 10baseT
- interface
-
- make TQM860L_FEC_80MHz_config
- - will configure for a TQM860L at 80 MHz with FEC for ethernet
-
- make TQM823L_LCD_config
- - will configure for a TQM823L with U-Boot console on LCD
-
- make TQM823L_LCD_80MHz_config
- - will configure for a TQM823L at 80 MHz with U-Boot console on LCD
-
- etc.
-
-
-Finally, type "make all", and you should get some working U-Boot
-images ready for download to / installation on your system:
-
-- "u-boot.bin" is a raw binary image
-- "u-boot" is an image in ELF binary format
-- "u-boot.srec" is in Motorola S-Record format
-
-
-Please be aware that the Makefiles assume you are using GNU make, so
-for instance on NetBSD you might need to use "gmake" instead of
-native "make".
-
-
-If the system board that you have is not listed, then you will need
-to port U-Boot to your hardware platform. To do this, follow these
-steps:
-
-1. Add a new configuration option for your board to the toplevel
- "Makefile" and to the "MAKEALL" script, using the existing
- entries as examples. Note that here and at many other places
- boards and other names are listed in alphabetical sort order. Please
- keep this order.
-2. Create a new directory to hold your board specific code. Add any
- files you need. In your board directory, you will need at least
- the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
-3. Create a new configuration file "include/configs/<board>.h" for
- your board
-3. If you're porting U-Boot to a new CPU, then also create a new
- directory to hold your CPU specific code. Add any files you need.
-4. Run "make <board>_config" with your new name.
-5. Type "make", and you should get a working "u-boot.srec" file
- to be installed on your target system.
-6. Debug and solve any problems that might arise.
- [Of course, this last step is much harder than it sounds.]
-
-
-Testing of U-Boot Modifications, Ports to New Hardware, etc.:
-==============================================================
-
-If you have modified U-Boot sources (for instance added a new board
-or support for new devices, a new CPU, etc.) you are expected to
-provide feedback to the other developers. The feedback normally takes
-the form of a "patch", i. e. a context diff against a certain (latest
-official or latest in CVS) version of U-Boot sources.
-
-But before you submit such a patch, please verify that your modifi-
-cation did not break existing code. At least make sure that *ALL* of
-the supported boards compile WITHOUT ANY compiler warnings. To do so,
-just run the "MAKEALL" script, which will configure and build U-Boot
-for ALL supported system. Be warned, this will take a while. You can
-select which (cross) compiler to use by passing a `CROSS_COMPILE'
-environment variable to the script, i. e. to use the cross tools from
-MontaVista's Hard Hat Linux you can type
-
- CROSS_COMPILE=ppc_8xx- MAKEALL
-
-or to build on a native PowerPC system you can type
-
- CROSS_COMPILE=' ' MAKEALL
-
-See also "U-Boot Porting Guide" below.
-
-
-Monitor Commands - Overview:
-============================
-
-go - start application at address 'addr'
-run - run commands in an environment variable
-bootm - boot application image from memory
-bootp - boot image via network using BootP/TFTP protocol
-tftpboot- boot image via network using TFTP protocol
- and env variables "ipaddr" and "serverip"
- (and eventually "gatewayip")
-rarpboot- boot image via network using RARP/TFTP protocol
-diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
-loads - load S-Record file over serial line
-loadb - load binary file over serial line (kermit mode)
-md - memory display
-mm - memory modify (auto-incrementing)
-nm - memory modify (constant address)
-mw - memory write (fill)
-cp - memory copy
-cmp - memory compare
-crc32 - checksum calculation
-imd - i2c memory display
-imm - i2c memory modify (auto-incrementing)
-inm - i2c memory modify (constant address)
-imw - i2c memory write (fill)
-icrc32 - i2c checksum calculation
-iprobe - probe to discover valid I2C chip addresses
-iloop - infinite loop on address range
-isdram - print SDRAM configuration information
-sspi - SPI utility commands
-base - print or set address offset
-printenv- print environment variables
-setenv - set environment variables
-saveenv - save environment variables to persistent storage
-protect - enable or disable FLASH write protection
-erase - erase FLASH memory
-flinfo - print FLASH memory information
-bdinfo - print Board Info structure
-iminfo - print header information for application image
-coninfo - print console devices and informations
-ide - IDE sub-system
-loop - infinite loop on address range
-mtest - simple RAM test
-icache - enable or disable instruction cache
-dcache - enable or disable data cache
-reset - Perform RESET of the CPU
-echo - echo args to console
-version - print monitor version
-help - print online help
-? - alias for 'help'
-
-
-Monitor Commands - Detailed Description:
-========================================
-
-TODO.
-
-For now: just type "help <command>".
-
-
-Environment Variables:
-======================
-
-U-Boot supports user configuration using Environment Variables which
-can be made persistent by saving to Flash memory.
-
-Environment Variables are set using "setenv", printed using
-"printenv", and saved to Flash using "saveenv". Using "setenv"
-without a value can be used to delete a variable from the
-environment. As long as you don't save the environment you are
-working with an in-memory copy. In case the Flash area containing the
-environment is erased by accident, a default environment is provided.
-
-Some configuration options can be set using Environment Variables:
+ ADCIOP_config ADS860_config AR405_config
+ at91rm9200dk_config CANBT_config cmi_mpc5xx_config
+ cogent_common_config cogent_mpc8260_config cogent_mpc8xx_config
+ CPCI405_config CPCIISER4_config CU824_config
+ DUET_ADS_config EBONY_config ELPT860_config
+ ESTEEM192E_config ETX094_config FADS823_config
+ FADS850SAR_config FADS860T_config FPS850L_config
+ FPS860L_config GEN860T_config GENIETV_config
+ GTH_config hermes_config hymod_config
+ IP860_config IVML24_config IVMS8_config
+ JSE_config LANTEC_config lwmon_config
+ MBX860T_config MBX_config MPC8260ADS_config
+ MPC8540ADS_config MPC8560ADS_config NETVIA_config
+ omap1510inn_config omap1610h2_config omap1610inn_config
+ pcu_e_config PIP405_config QS823_config
+ QS850_config QS860T_config RPXlite_config
+ RPXsuper_config rsdproto_config Sandpoint8240_config
+ sbc8260_config SM850_config SPD823TS_config
+ stxgp3_config SXNI855T_config TQM823L_config
+ TQM850L_config TQM855L_config TQM860L_config
+ WALNUT405_config ZPC1900_config
+
+ Note: for some board special configuration names may exist; check if
+ additional information is available from the board vendor; for
+ instance, the TQM8xxL systems run normally at 50 MHz and use a
+ SCC for 10baseT ethernet; there are also systems with 80 MHz
+ CPU clock, and an optional Fast Ethernet module is available
+ for CPU's with FEC. You can select such additional "features"
+ when chosing the configuration, i. e.
+
+ make TQM860L_config
+ - will configure for a plain TQM860L, i. e. 50MHz, no FEC
+
+ make TQM860L_FEC_config
+ - will configure for a TQM860L at 50MHz with FEC for ethernet
+
+ make TQM860L_80MHz_config
+ - will configure for a TQM860L at 80 MHz, with normal 10baseT
+ interface
+
+ make TQM860L_FEC_80MHz_config
+ - will configure for a TQM860L at 80 MHz with FEC for ethernet
+
+ make TQM823L_LCD_config
+ - will configure for a TQM823L with U-Boot console on LCD
+
+ make TQM823L_LCD_80MHz_config
+ - will configure for a TQM823L at 80 MHz with U-Boot console on LCD
+
+ etc.
+
+
+ Finally, type "make all", and you should get some working U-Boot
+ images ready for download to / installation on your system:
+
+ - "u-boot.bin" is a raw binary image
+ - "u-boot" is an image in ELF binary format
+ - "u-boot.srec" is in Motorola S-Record format
+
+
+ Please be aware that the Makefiles assume you are using GNU make, so
+ for instance on NetBSD you might need to use "gmake" instead of
+ native "make".
+
+
+ If the system board that you have is not listed, then you will need
+ to port U-Boot to your hardware platform. To do this, follow these
+ steps:
+
+ 1. Add a new configuration option for your board to the toplevel
+ "Makefile" and to the "MAKEALL" script, using the existing
+ entries as examples. Note that here and at many other places
+ boards and other names are listed in alphabetical sort order. Please
+ keep this order.
+ 2. Create a new directory to hold your board specific code. Add any
+ files you need. In your board directory, you will need at least
+ the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
+ 3. Create a new configuration file "include/configs/<board>.h" for
+ your board
+ 3. If you're porting U-Boot to a new CPU, then also create a new
+ directory to hold your CPU specific code. Add any files you need.
+ 4. Run "make <board>_config" with your new name.
+ 5. Type "make", and you should get a working "u-boot.srec" file
+ to be installed on your target system.
+ 6. Debug and solve any problems that might arise.
+ [Of course, this last step is much harder than it sounds.]
+
+
+ Testing of U-Boot Modifications, Ports to New Hardware, etc.:
+ ==============================================================
+
+ If you have modified U-Boot sources (for instance added a new board
+ or support for new devices, a new CPU, etc.) you are expected to
+ provide feedback to the other developers. The feedback normally takes
+ the form of a "patch", i. e. a context diff against a certain (latest
+ official or latest in CVS) version of U-Boot sources.
+
+ But before you submit such a patch, please verify that your modifi-
+ cation did not break existing code. At least make sure that *ALL* of
+ the supported boards compile WITHOUT ANY compiler warnings. To do so,
+ just run the "MAKEALL" script, which will configure and build U-Boot
+ for ALL supported system. Be warned, this will take a while. You can
+ select which (cross) compiler to use by passing a `CROSS_COMPILE'
+ environment variable to the script, i. e. to use the cross tools from
+ MontaVista's Hard Hat Linux you can type
+
+ CROSS_COMPILE=ppc_8xx- MAKEALL
+
+ or to build on a native PowerPC system you can type
+
+ CROSS_COMPILE=' ' MAKEALL
+
+ See also "U-Boot Porting Guide" below.
+
+
+ Monitor Commands - Overview:
+ ============================
+
+ go - start application at address 'addr'
+ run - run commands in an environment variable
+ bootm - boot application image from memory
+ bootp - boot image via network using BootP/TFTP protocol
+ tftpboot- boot image via network using TFTP protocol
+ and env variables "ipaddr" and "serverip"
+ (and eventually "gatewayip")
+ rarpboot- boot image via network using RARP/TFTP protocol
+ diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
+ loads - load S-Record file over serial line
+ loadb - load binary file over serial line (kermit mode)
+ md - memory display
+ mm - memory modify (auto-incrementing)
+ nm - memory modify (constant address)
+ mw - memory write (fill)
+ cp - memory copy
+ cmp - memory compare
+ crc32 - checksum calculation
+ imd - i2c memory display
+ imm - i2c memory modify (auto-incrementing)
+ inm - i2c memory modify (constant address)
+ imw - i2c memory write (fill)
+ icrc32 - i2c checksum calculation
+ iprobe - probe to discover valid I2C chip addresses
+ iloop - infinite loop on address range
+ isdram - print SDRAM configuration information
+ sspi - SPI utility commands
+ base - print or set address offset
+ printenv- print environment variables
+ setenv - set environment variables
+ saveenv - save environment variables to persistent storage
+ protect - enable or disable FLASH write protection
+ erase - erase FLASH memory
+ flinfo - print FLASH memory information
+ bdinfo - print Board Info structure
+ iminfo - print header information for application image
+ coninfo - print console devices and informations
+ ide - IDE sub-system
+ loop - infinite loop on address range
+ mtest - simple RAM test
+ icache - enable or disable instruction cache
+ dcache - enable or disable data cache
+ reset - Perform RESET of the CPU
+ echo - echo args to console
+ version - print monitor version
+ help - print online help
+ ? - alias for 'help'
+
+
+ Monitor Commands - Detailed Description:
+ ========================================
+
+ TODO.
+
+ For now: just type "help <command>".
+
+
+ Environment Variables:
+ ======================
+
+ U-Boot supports user configuration using Environment Variables which
+ can be made persistent by saving to Flash memory.
+
+ Environment Variables are set using "setenv", printed using
+ "printenv", and saved to Flash using "saveenv". Using "setenv"
+ without a value can be used to delete a variable from the
+ environment. As long as you don't save the environment you are
+ working with an in-memory copy. In case the Flash area containing the
+ environment is erased by accident, a default environment is provided.
+
+ Some configuration options can be set using Environment Variables:
+
+ baudrate - see CONFIG_BAUDRATE
+
+ bootdelay - see CONFIG_BOOTDELAY
+
+ bootcmd - see CONFIG_BOOTCOMMAND
+
+ bootargs - Boot arguments when booting an RTOS image
+
+ bootfile - Name of the image to load with TFTP
+
+ autoload - if set to "no" (any string beginning with 'n'),
+ "bootp" will just load perform a lookup of the
+ configuration from the BOOTP server, but not try to
+ load any image using TFTP
+
+ autostart - if set to "yes", an image loaded using the "bootp",
+ "rarpboot", "tftpboot" or "diskboot" commands will
+ be automatically started (by internally calling
+ "bootm")
+
+ If set to "no", a standalone image passed to the
+ "bootm" command will be copied to the load address
+ (and eventually uncompressed), but NOT be started.
+ This can be used to load and uncompress arbitrary
+ data.
+
+ initrd_high - restrict positioning of initrd images:
+ If this variable is not set, initrd images will be
+ copied to the highest possible address in RAM; this
+ is usually what you want since it allows for
+ maximum initrd size. If for some reason you want to
+ make sure that the initrd image is loaded below the
+ CFG_BOOTMAPSZ limit, you can set this environment
+ variable to a value of "no" or "off" or "0".
+ Alternatively, you can set it to a maximum upper
+ address to use (U-Boot will still check that it
+ does not overwrite the U-Boot stack and data).
+
+ For instance, when you have a system with 16 MB
+ RAM, and want to reserve 4 MB from use by Linux,
+ you can do this by adding "mem=12M" to the value of
+ the "bootargs" variable. However, now you must make
+ sure that the initrd image is placed in the first
+ 12 MB as well - this can be done with
+
+ setenv initrd_high 00c00000
+
+ If you set initrd_high to 0xFFFFFFFF, this is an
+ indication to U-Boot that all addresses are legal
+ for the Linux kernel, including addresses in flash
+ memory. In this case U-Boot will NOT COPY the
+ ramdisk at all. This may be useful to reduce the
+ boot time on your system, but requires that this
+ feature is supported by your Linux kernel.
- baudrate - see CONFIG_BAUDRATE
+ ipaddr - IP address; needed for tftpboot command
- bootdelay - see CONFIG_BOOTDELAY
+ loadaddr - Default load address for commands like "bootp",
+ "rarpboot", "tftpboot", "loadb" or "diskboot"
- bootcmd - see CONFIG_BOOTCOMMAND
+ loads_echo - see CONFIG_LOADS_ECHO
- bootargs - Boot arguments when booting an RTOS image
+ serverip - TFTP server IP address; needed for tftpboot command
- bootfile - Name of the image to load with TFTP
+ bootretry - see CONFIG_BOOT_RETRY_TIME
- autoload - if set to "no" (any string beginning with 'n'),
- "bootp" will just load perform a lookup of the
- configuration from the BOOTP server, but not try to
- load any image using TFTP
+ bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
- autostart - if set to "yes", an image loaded using the "bootp",
- "rarpboot", "tftpboot" or "diskboot" commands will
- be automatically started (by internally calling
- "bootm")
+ bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
- If set to "no", a standalone image passed to the
- "bootm" command will be copied to the load address
- (and eventually uncompressed), but NOT be started.
- This can be used to load and uncompress arbitrary
- data.
+ ethprime - When CONFIG_NET_MULTI is enabled controls which
+ interface is used first.
- initrd_high - restrict positioning of initrd images:
- If this variable is not set, initrd images will be
- copied to the highest possible address in RAM; this
- is usually what you want since it allows for
- maximum initrd size. If for some reason you want to
- make sure that the initrd image is loaded below the
- CFG_BOOTMAPSZ limit, you can set this environment
- variable to a value of "no" or "off" or "0".
- Alternatively, you can set it to a maximum upper
- address to use (U-Boot will still check that it
- does not overwrite the U-Boot stack and data).
+ ethact - When CONFIG_NET_MULTI is enabled controls which
+ interface is currently active. For example you
+ can do the following
- For instance, when you have a system with 16 MB
- RAM, and want to reserve 4 MB from use by Linux,
- you can do this by adding "mem=12M" to the value of
- the "bootargs" variable. However, now you must make
- sure that the initrd image is placed in the first
- 12 MB as well - this can be done with
+ => setenv ethact FEC ETHERNET
+ => ping 192.168.0.1 # traffic sent on FEC ETHERNET
+ => setenv ethact SCC ETHERNET
+ => ping 10.0.0.1 # traffic sent on SCC ETHERNET
- setenv initrd_high 00c00000
+ netretry - When set to "no" each network operation will
+ either succeed or fail without retrying.
+ When set to "once" the network operation will
+ fail when all the available network interfaces
+ are tried once without success.
+ Useful on scripts which control the retry operation
+ themselves.
- If you set initrd_high to 0xFFFFFFFF, this is an
- indication to U-Boot that all addresses are legal
- for the Linux kernel, including addresses in flash
- memory. In this case U-Boot will NOT COPY the
- ramdisk at all. This may be useful to reduce the
- boot time on your system, but requires that this
- feature is supported by your Linux kernel.
+ vlan - When set to a value < 4095 the traffic over
+ ethernet is encapsulated/received over 802.1q
+ VLAN tagged frames.
- ipaddr - IP address; needed for tftpboot command
+ The following environment variables may be used and automatically
+ updated by the network boot commands ("bootp" and "rarpboot"),
+ depending the information provided by your boot server:
- loadaddr - Default load address for commands like "bootp",
- "rarpboot", "tftpboot", "loadb" or "diskboot"
+ bootfile - see above
+ dnsip - IP address of your Domain Name Server
+ dnsip2 - IP address of your secondary Domain Name Server
+ gatewayip - IP address of the Gateway (Router) to use
+ hostname - Target hostname
+ ipaddr - see above
+ netmask - Subnet Mask
+ rootpath - Pathname of the root filesystem on the NFS server
+ serverip - see above
- loads_echo - see CONFIG_LOADS_ECHO
- serverip - TFTP server IP address; needed for tftpboot command
+ There are two special Environment Variables:
- bootretry - see CONFIG_BOOT_RETRY_TIME
+ serial# - contains hardware identification information such
+ as type string and/or serial number
+ ethaddr - Ethernet address
- bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
+ These variables can be set only once (usually during manufacturing of
+ the board). U-Boot refuses to delete or overwrite these variables
+ once they have been set once.
- bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
+ Further special Environment Variables:
-The following environment variables may be used and automatically
-updated by the network boot commands ("bootp" and "rarpboot"),
-depending the information provided by your boot server:
+ ver - Contains the U-Boot version string as printed
+ with the "version" command. This variable is
+ readonly (see CONFIG_VERSION_VARIABLE).
- bootfile - see above
- dnsip - IP address of your Domain Name Server
- dnsip2 - IP address of your secondary Domain Name Server
- gatewayip - IP address of the Gateway (Router) to use
- hostname - Target hostname
- ipaddr - see above
- netmask - Subnet Mask
- rootpath - Pathname of the root filesystem on the NFS server
- serverip - see above
+
+ Please note that changes to some configuration parameters may take
+ only effect after the next boot (yes, that's just like Windoze :-).
-There are two special Environment Variables:
+ Command Line Parsing:
+ =====================
- serial# - contains hardware identification information such
- as type string and/or serial number
- ethaddr - Ethernet address
+ There are two different command line parsers available with U-Boot:
+ the old "simple" one, and the much more powerful "hush" shell:
-These variables can be set only once (usually during manufacturing of
-the board). U-Boot refuses to delete or overwrite these variables
-once they have been set once.
+ Old, simple command line parser:
+ --------------------------------
+ - supports environment variables (through setenv / saveenv commands)
+ - several commands on one line, separated by ';'
+ - variable substitution using "... $(name) ..." syntax
+ - special characters ('$', ';') can be escaped by prefixing with '\',
+ for example:
+ setenv bootcmd bootm \$(address)
+ - You can also escape text by enclosing in single apostrophes, for example:
+ setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
-Further special Environment Variables:
+ Hush shell:
+ -----------
- ver - Contains the U-Boot version string as printed
- with the "version" command. This variable is
- readonly (see CONFIG_VERSION_VARIABLE).
+ - similar to Bourne shell, with control structures like
+ if...then...else...fi, for...do...done; while...do...done,
+ until...do...done, ...
+ - supports environment ("global") variables (through setenv / saveenv
+ commands) and local shell variables (through standard shell syntax
+ "name=value"); only environment variables can be used with "run"
+ command
+ General rules:
+ --------------
-Please note that changes to some configuration parameters may take
-only effect after the next boot (yes, that's just like Windoze :-).
+ (1) If a command line (or an environment variable executed by a "run"
+ command) contains several commands separated by semicolon, and
+ one of these commands fails, then the remaining commands will be
+ executed anyway.
+ (2) If you execute several variables with one call to run (i. e.
+ calling run with a list af variables as arguments), any failing
+ command will cause "run" to terminate, i. e. the remaining
+ variables are not executed.
-Command Line Parsing:
-=====================
+ Note for Redundant Ethernet Interfaces:
+ =======================================
-There are two different command line parsers available with U-Boot:
-the old "simple" one, and the much more powerful "hush" shell:
+ Some boards come with redundant ethernet interfaces; U-Boot supports
+ such configurations and is capable of automatic selection of a
+ "working" interface when needed. MAC assignment works as follows:
-Old, simple command line parser:
---------------------------------
+ Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
+ MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
+ "eth1addr" (=>eth1), "eth2addr", ...
-- supports environment variables (through setenv / saveenv commands)
-- several commands on one line, separated by ';'
-- variable substitution using "... $(name) ..." syntax
-- special characters ('$', ';') can be escaped by prefixing with '\',
- for example:
- setenv bootcmd bootm \$(address)
-- You can also escape text by enclosing in single apostrophes, for example:
- setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
+ If the network interface stores some valid MAC address (for instance
+ in SROM), this is used as default address if there is NO correspon-
+ ding setting in the environment; if the corresponding environment
+ variable is set, this overrides the settings in the card; that means:
-Hush shell:
------------
+ o If the SROM has a valid MAC address, and there is no address in the
+ environment, the SROM's address is used.
-- similar to Bourne shell, with control structures like
- if...then...else...fi, for...do...done; while...do...done,
- until...do...done, ...
-- supports environment ("global") variables (through setenv / saveenv
- commands) and local shell variables (through standard shell syntax
- "name=value"); only environment variables can be used with "run"
- command
+ o If there is no valid address in the SROM, and a definition in the
+ environment exists, then the value from the environment variable is
+ used.
-General rules:
---------------
+ o If both the SROM and the environment contain a MAC address, and
+ both addresses are the same, this MAC address is used.
-(1) If a command line (or an environment variable executed by a "run"
- command) contains several commands separated by semicolon, and
- one of these commands fails, then the remaining commands will be
- executed anyway.
+ o If both the SROM and the environment contain a MAC address, and the
+ addresses differ, the value from the environment is used and a
+ warning is printed.
-(2) If you execute several variables with one call to run (i. e.
- calling run with a list af variables as arguments), any failing
- command will cause "run" to terminate, i. e. the remaining
- variables are not executed.
+ o If neither SROM nor the environment contain a MAC address, an error
+ is raised.
-Note for Redundant Ethernet Interfaces:
-=======================================
-Some boards come with redundant ethernet interfaces; U-Boot supports
-such configurations and is capable of automatic selection of a
-"working" interface when needed. MAC assignment works as follows:
+ Image Formats:
+ ==============
-Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
-MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
-"eth1addr" (=>eth1), "eth2addr", ...
+ The "boot" commands of this monitor operate on "image" files which
+ can be basicly anything, preceeded by a special header; see the
+ definitions in include/image.h for details; basicly, the header
+ defines the following image properties:
-If the network interface stores some valid MAC address (for instance
-in SROM), this is used as default address if there is NO correspon-
-ding setting in the environment; if the corresponding environment
-variable is set, this overrides the settings in the card; that means:
+ * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
+ 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
+ LynxOS, pSOS, QNX, RTEMS, ARTOS;
+ Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
+ * Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
+ IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
+ Currently supported: ARM, Intel x86, MIPS, NIOS, PowerPC).
+ * Compression Type (uncompressed, gzip, bzip2)
+ * Load Address
+ * Entry Point
+ * Image Name
+ * Image Timestamp
-o If the SROM has a valid MAC address, and there is no address in the
- environment, the SROM's address is used.
+ The header is marked by a special Magic Number, and both the header
+ and the data portions of the image are secured against corruption by
+ CRC32 checksums.
-o If there is no valid address in the SROM, and a definition in the
- environment exists, then the value from the environment variable is
- used.
-o If both the SROM and the environment contain a MAC address, and
- both addresses are the same, this MAC address is used.
+ Linux Support:
+ ==============
-o If both the SROM and the environment contain a MAC address, and the
- addresses differ, the value from the environment is used and a
- warning is printed.
+ Although U-Boot should support any OS or standalone application
+ easily, the main focus has always been on Linux during the design of
+ U-Boot.
-o If neither SROM nor the environment contain a MAC address, an error
- is raised.
+ U-Boot includes many features that so far have been part of some
+ special "boot loader" code within the Linux kernel. Also, any
+ "initrd" images to be used are no longer part of one big Linux image;
+ instead, kernel and "initrd" are separate images. This implementation
+ serves several purposes:
+ - the same features can be used for other OS or standalone
+ applications (for instance: using compressed images to reduce the
+ Flash memory footprint)
-Image Formats:
-==============
+ - it becomes much easier to port new Linux kernel versions because
+ lots of low-level, hardware dependent stuff are done by U-Boot
-The "boot" commands of this monitor operate on "image" files which
-can be basicly anything, preceeded by a special header; see the
-definitions in include/image.h for details; basicly, the header
-defines the following image properties:
+ - the same Linux kernel image can now be used with different "initrd"
+ images; of course this also means that different kernel images can
+ be run with the same "initrd". This makes testing easier (you don't
+ have to build a new "zImage.initrd" Linux image when you just
+ change a file in your "initrd"). Also, a field-upgrade of the
+ software is easier now.
-* Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
- 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
- LynxOS, pSOS, QNX, RTEMS, ARTOS;
- Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
-* Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
- IA64, MIPS, MIPS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
- Currently supported: PowerPC).
-* Compression Type (uncompressed, gzip, bzip2)
-* Load Address
-* Entry Point
-* Image Name
-* Image Timestamp
-The header is marked by a special Magic Number, and both the header
-and the data portions of the image are secured against corruption by
-CRC32 checksums.
+ Linux HOWTO:
+ ============
+ Porting Linux to U-Boot based systems:
+ ---------------------------------------
-Linux Support:
-==============
+ U-Boot cannot save you from doing all the necessary modifications to
+ configure the Linux device drivers for use with your target hardware
+ (no, we don't intend to provide a full virtual machine interface to
+ Linux :-).
-Although U-Boot should support any OS or standalone application
-easily, the main focus has always been on Linux during the design of
-U-Boot.
+ But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
-U-Boot includes many features that so far have been part of some
-special "boot loader" code within the Linux kernel. Also, any
-"initrd" images to be used are no longer part of one big Linux image;
-instead, kernel and "initrd" are separate images. This implementation
-serves several purposes:
+ Just make sure your machine specific header file (for instance
+ include/asm-ppc/tqm8xx.h) includes the same definition of the Board
+ Information structure as we define in include/u-boot.h, and make
+ sure that your definition of IMAP_ADDR uses the same value as your
+ U-Boot configuration in CFG_IMMR.
-- the same features can be used for other OS or standalone
- applications (for instance: using compressed images to reduce the
- Flash memory footprint)
-- it becomes much easier to port new Linux kernel versions because
- lots of low-level, hardware dependent stuff are done by U-Boot
+ Configuring the Linux kernel:
+ -----------------------------
-- the same Linux kernel image can now be used with different "initrd"
- images; of course this also means that different kernel images can
- be run with the same "initrd". This makes testing easier (you don't
- have to build a new "zImage.initrd" Linux image when you just
- change a file in your "initrd"). Also, a field-upgrade of the
- software is easier now.
+ No specific requirements for U-Boot. Make sure you have some root
+ device (initial ramdisk, NFS) for your target system.
-Linux HOWTO:
-============
+ Building a Linux Image:
+ -----------------------
-Porting Linux to U-Boot based systems:
----------------------------------------
+ With U-Boot, "normal" build targets like "zImage" or "bzImage" are
+ not used. If you use recent kernel source, a new build target
+ "uImage" will exist which automatically builds an image usable by
+ U-Boot. Most older kernels also have support for a "pImage" target,
+ which was introduced for our predecessor project PPCBoot and uses a
+ 100% compatible format.
-U-Boot cannot save you from doing all the necessary modifications to
-configure the Linux device drivers for use with your target hardware
-(no, we don't intend to provide a full virtual machine interface to
-Linux :-).
+ Example:
-But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
+ make TQM850L_config
+ make oldconfig
+ make dep
+ make uImage
-Just make sure your machine specific header file (for instance
-include/asm-ppc/tqm8xx.h) includes the same definition of the Board
-Information structure as we define in include/u-boot.h, and make
-sure that your definition of IMAP_ADDR uses the same value as your
-U-Boot configuration in CFG_IMMR.
+ The "uImage" build target uses a special tool (in 'tools/mkimage') to
+ encapsulate a compressed Linux kernel image with header information,
+ CRC32 checksum etc. for use with U-Boot. This is what we are doing:
+ * build a standard "vmlinux" kernel image (in ELF binary format):
+
+ * convert the kernel into a raw binary image:
+
+ ${CROSS_COMPILE}-objcopy -O binary \
+ -R .note -R .comment \
+ -S vmlinux linux.bin
+
+ * compress the binary image:
+
+ gzip -9 linux.bin
-Configuring the Linux kernel:
------------------------------
+ * package compressed binary image for U-Boot:
-No specific requirements for U-Boot. Make sure you have some root
-device (initial ramdisk, NFS) for your target system.
+ mkimage -A ppc -O linux -T kernel -C gzip \
+ -a 0 -e 0 -n "Linux Kernel Image" \
+ -d linux.bin.gz uImage
-Building a Linux Image:
------------------------
+ The "mkimage" tool can also be used to create ramdisk images for use
+ with U-Boot, either separated from the Linux kernel image, or
+ combined into one file. "mkimage" encapsulates the images with a 64
+ byte header containing information about target architecture,
+ operating system, image type, compression method, entry points, time
+ stamp, CRC32 checksums, etc.
-With U-Boot, "normal" build targets like "zImage" or "bzImage" are
-not used. If you use recent kernel source, a new build target
-"uImage" will exist which automatically builds an image usable by
-U-Boot. Most older kernels also have support for a "pImage" target,
-which was introduced for our predecessor project PPCBoot and uses a
-100% compatible format.
-
-Example:
-
- make TQM850L_config
- make oldconfig
- make dep
- make uImage
-
-The "uImage" build target uses a special tool (in 'tools/mkimage') to
-encapsulate a compressed Linux kernel image with header information,
-CRC32 checksum etc. for use with U-Boot. This is what we are doing:
-
-* build a standard "vmlinux" kernel image (in ELF binary format):
-
-* convert the kernel into a raw binary image:
-
- ${CROSS_COMPILE}-objcopy -O binary \
- -R .note -R .comment \
- -S vmlinux linux.bin
-
-* compress the binary image:
-
- gzip -9 linux.bin
-
-* package compressed binary image for U-Boot:
-
- mkimage -A ppc -O linux -T kernel -C gzip \
- -a 0 -e 0 -n "Linux Kernel Image" \
- -d linux.bin.gz uImage
+ "mkimage" can be called in two ways: to verify existing images and
+ print the header information, or to build new images.
+ In the first form (with "-l" option) mkimage lists the information
+ contained in the header of an existing U-Boot image; this includes
+ checksum verification:
-The "mkimage" tool can also be used to create ramdisk images for use
-with U-Boot, either separated from the Linux kernel image, or
-combined into one file. "mkimage" encapsulates the images with a 64
-byte header containing information about target architecture,
-operating system, image type, compression method, entry points, time
-stamp, CRC32 checksums, etc.
-
-"mkimage" can be called in two ways: to verify existing images and
-print the header information, or to build new images.
-
-In the first form (with "-l" option) mkimage lists the information
-contained in the header of an existing U-Boot image; this includes
-checksum verification:
+ tools/mkimage -l image
+ -l ==> list image header information
- tools/mkimage -l image
- -l ==> list image header information
+ The second form (with "-d" option) is used to build a U-Boot image
+ from a "data file" which is used as image payload:
-The second form (with "-d" option) is used to build a U-Boot image
-from a "data file" which is used as image payload:
-
- tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
- -n name -d data_file image
- -A ==> set architecture to 'arch'
- -O ==> set operating system to 'os'
- -T ==> set image type to 'type'
- -C ==> set compression type 'comp'
- -a ==> set load address to 'addr' (hex)
- -e ==> set entry point to 'ep' (hex)
- -n ==> set image name to 'name'
- -d ==> use image data from 'datafile'
+ tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
+ -n name -d data_file image
+ -A ==> set architecture to 'arch'
+ -O ==> set operating system to 'os'
+ -T ==> set image type to 'type'
+ -C ==> set compression type 'comp'
+ -a ==> set load address to 'addr' (hex)
+ -e ==> set entry point to 'ep' (hex)
+ -n ==> set image name to 'name'
+ -d ==> use image data from 'datafile'
-Right now, all Linux kernels use the same load address (0x00000000),
-but the entry point address depends on the kernel version:
-
-- 2.2.x kernels have the entry point at 0x0000000C,
-- 2.3.x and later kernels have the entry point at 0x00000000.
-
-So a typical call to build a U-Boot image would read:
-
- -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
- > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
- > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
- > examples/uImage.TQM850L
- Image Name: 2.4.4 kernel for TQM850L
- Created: Wed Jul 19 02:34:59 2000
- Image Type: PowerPC Linux Kernel Image (gzip compressed)
- Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
- Load Address: 0x00000000
- Entry Point: 0x00000000
+ Right now, all Linux kernels use the same load address (0x00000000),
+ but the entry point address depends on the kernel version:
-To verify the contents of the image (or check for corruption):
+ - 2.2.x kernels have the entry point at 0x0000000C,
+ - 2.3.x and later kernels have the entry point at 0x00000000.
- -> tools/mkimage -l examples/uImage.TQM850L
- Image Name: 2.4.4 kernel for TQM850L
- Created: Wed Jul 19 02:34:59 2000
- Image Type: PowerPC Linux Kernel Image (gzip compressed)
- Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
- Load Address: 0x00000000
- Entry Point: 0x00000000
+ So a typical call to build a U-Boot image would read:
-NOTE: for embedded systems where boot time is critical you can trade
-speed for memory and install an UNCOMPRESSED image instead: this
-needs more space in Flash, but boots much faster since it does not
-need to be uncompressed:
-
- -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
- -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
- > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
- > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
- > examples/uImage.TQM850L-uncompressed
- Image Name: 2.4.4 kernel for TQM850L
- Created: Wed Jul 19 02:34:59 2000
- Image Type: PowerPC Linux Kernel Image (uncompressed)
- Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
- Load Address: 0x00000000
- Entry Point: 0x00000000
-
-
-Similar you can build U-Boot images from a 'ramdisk.image.gz' file
-when your kernel is intended to use an initial ramdisk:
-
- -> tools/mkimage -n 'Simple Ramdisk Image' \
- > -A ppc -O linux -T ramdisk -C gzip \
- > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
- Image Name: Simple Ramdisk Image
- Created: Wed Jan 12 14:01:50 2000
- Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
- Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
- Load Address: 0x00000000
- Entry Point: 0x00000000
-
-
-Installing a Linux Image:
--------------------------
-
-To downloading a U-Boot image over the serial (console) interface,
-you must convert the image to S-Record format:
-
- objcopy -I binary -O srec examples/image examples/image.srec
-
-The 'objcopy' does not understand the information in the U-Boot
-image header, so the resulting S-Record file will be relative to
-address 0x00000000. To load it to a given address, you need to
-specify the target address as 'offset' parameter with the 'loads'
-command.
-
-Example: install the image to address 0x40100000 (which on the
-TQM8xxL is in the first Flash bank):
-
- => erase 40100000 401FFFFF
-
- .......... done
- Erased 8 sectors
-
- => loads 40100000
- ## Ready for S-Record download ...
- ~>examples/image.srec
- 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
- ...
- 15989 15990 15991 15992
- [file transfer complete]
- [connected]
- ## Start Addr = 0x00000000
-
-
-You can check the success of the download using the 'iminfo' command;
-this includes a checksum verification so you can be sure no data
-corruption happened:
-
- => imi 40100000
-
- ## Checking Image at 40100000 ...
- Image Name: 2.2.13 for initrd on TQM850L
- Image Type: PowerPC Linux Kernel Image (gzip compressed)
- Data Size: 335725 Bytes = 327 kB = 0 MB
- Load Address: 00000000
- Entry Point: 0000000c
- Verifying Checksum ... OK
-
-
-Boot Linux:
------------
-
-The "bootm" command is used to boot an application that is stored in
-memory (RAM or Flash). In case of a Linux kernel image, the contents
-of the "bootargs" environment variable is passed to the kernel as
-parameters. You can check and modify this variable using the
-"printenv" and "setenv" commands:
-
-
- => printenv bootargs
- bootargs=root=/dev/ram
-
- => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
-
- => printenv bootargs
- bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
-
- => bootm 40020000
- ## Booting Linux kernel at 40020000 ...
- Image Name: 2.2.13 for NFS on TQM850L
- Image Type: PowerPC Linux Kernel Image (gzip compressed)
- Data Size: 381681 Bytes = 372 kB = 0 MB
- Load Address: 00000000
- Entry Point: 0000000c
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
- Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
- time_init: decrementer frequency = 187500000/60
- Calibrating delay loop... 49.77 BogoMIPS
- Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
- ...
-
-If you want to boot a Linux kernel with initial ram disk, you pass
-the memory addresses of both the kernel and the initrd image (PPBCOOT
-format!) to the "bootm" command:
-
- => imi 40100000 40200000
-
- ## Checking Image at 40100000 ...
- Image Name: 2.2.13 for initrd on TQM850L
- Image Type: PowerPC Linux Kernel Image (gzip compressed)
- Data Size: 335725 Bytes = 327 kB = 0 MB
- Load Address: 00000000
- Entry Point: 0000000c
- Verifying Checksum ... OK
-
- ## Checking Image at 40200000 ...
- Image Name: Simple Ramdisk Image
- Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
- Data Size: 566530 Bytes = 553 kB = 0 MB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
-
- => bootm 40100000 40200000
- ## Booting Linux kernel at 40100000 ...
- Image Name: 2.2.13 for initrd on TQM850L
- Image Type: PowerPC Linux Kernel Image (gzip compressed)
- Data Size: 335725 Bytes = 327 kB = 0 MB
- Load Address: 00000000
- Entry Point: 0000000c
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- ## Loading RAMDisk Image at 40200000 ...
- Image Name: Simple Ramdisk Image
- Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
- Data Size: 566530 Bytes = 553 kB = 0 MB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- Loading Ramdisk ... OK
- Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
- Boot arguments: root=/dev/ram
- time_init: decrementer frequency = 187500000/60
- Calibrating delay loop... 49.77 BogoMIPS
- ...
- RAMDISK: Compressed image found at block 0
- VFS: Mounted root (ext2 filesystem).
-
- bash#
-
-More About U-Boot Image Types:
-------------------------------
-
-U-Boot supports the following image types:
-
- "Standalone Programs" are directly runnable in the environment
- provided by U-Boot; it is expected that (if they behave
- well) you can continue to work in U-Boot after return from
- the Standalone Program.
- "OS Kernel Images" are usually images of some Embedded OS which
- will take over control completely. Usually these programs
- will install their own set of exception handlers, device
- drivers, set up the MMU, etc. - this means, that you cannot
- expect to re-enter U-Boot except by resetting the CPU.
- "RAMDisk Images" are more or less just data blocks, and their
- parameters (address, size) are passed to an OS kernel that is
- being started.
- "Multi-File Images" contain several images, typically an OS
- (Linux) kernel image and one or more data images like
- RAMDisks. This construct is useful for instance when you want
- to boot over the network using BOOTP etc., where the boot
- server provides just a single image file, but you want to get
- for instance an OS kernel and a RAMDisk image.
-
- "Multi-File Images" start with a list of image sizes, each
- image size (in bytes) specified by an "uint32_t" in network
- byte order. This list is terminated by an "(uint32_t)0".
- Immediately after the terminating 0 follow the images, one by
- one, all aligned on "uint32_t" boundaries (size rounded up to
- a multiple of 4 bytes).
-
- "Firmware Images" are binary images containing firmware (like
- U-Boot or FPGA images) which usually will be programmed to
- flash memory.
-
- "Script files" are command sequences that will be executed by
- U-Boot's command interpreter; this feature is especially
- useful when you configure U-Boot to use a real shell (hush)
- as command interpreter.
-
-
-Standalone HOWTO:
-=================
-
-One of the features of U-Boot is that you can dynamically load and
-run "standalone" applications, which can use some resources of
-U-Boot like console I/O functions or interrupt services.
-
-Two simple examples are included with the sources:
-
-"Hello World" Demo:
--------------------
-
-'examples/hello_world.c' contains a small "Hello World" Demo
-application; it is automatically compiled when you build U-Boot.
-It's configured to run at address 0x00040004, so you can play with it
-like that:
-
- => loads
- ## Ready for S-Record download ...
- ~>examples/hello_world.srec
- 1 2 3 4 5 6 7 8 9 10 11 ...
- [file transfer complete]
- [connected]
- ## Start Addr = 0x00040004
-
- => go 40004 Hello World! This is a test.
- ## Starting application at 0x00040004 ...
- Hello World
- argc = 7
- argv[0] = "40004"
- argv[1] = "Hello"
- argv[2] = "World!"
- argv[3] = "This"
- argv[4] = "is"
- argv[5] = "a"
- argv[6] = "test."
- argv[7] = "<NULL>"
- Hit any key to exit ...
-
- ## Application terminated, rc = 0x0
-
-Another example, which demonstrates how to register a CPM interrupt
-handler with the U-Boot code, can be found in 'examples/timer.c'.
-Here, a CPM timer is set up to generate an interrupt every second.
-The interrupt service routine is trivial, just printing a '.'
-character, but this is just a demo program. The application can be
-controlled by the following keys:
-
- ? - print current values og the CPM Timer registers
- b - enable interrupts and start timer
- e - stop timer and disable interrupts
- q - quit application
-
- => loads
- ## Ready for S-Record download ...
- ~>examples/timer.srec
- 1 2 3 4 5 6 7 8 9 10 11 ...
- [file transfer complete]
- [connected]
- ## Start Addr = 0x00040004
-
- => go 40004
- ## Starting application at 0x00040004 ...
- TIMERS=0xfff00980
- Using timer 1
- tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
-
-Hit 'b':
- [q, b, e, ?] Set interval 1000000 us
- Enabling timer
-Hit '?':
- [q, b, e, ?] ........
- tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
-Hit '?':
- [q, b, e, ?] .
- tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
-Hit '?':
- [q, b, e, ?] .
- tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
-Hit '?':
- [q, b, e, ?] .
- tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
-Hit 'e':
- [q, b, e, ?] ...Stopping timer
-Hit 'q':
- [q, b, e, ?] ## Application terminated, rc = 0x0
-
-
-Minicom warning:
-================
-
-Over time, many people have reported problems when trying to use the
-"minicom" terminal emulation program for serial download. I (wd)
-consider minicom to be broken, and recommend not to use it. Under
-Unix, I recommend to use C-Kermit for general purpose use (and
-especially for kermit binary protocol download ("loadb" command), and
-use "cu" for S-Record download ("loads" command).
-
-Nevertheless, if you absolutely want to use it try adding this
-configuration to your "File transfer protocols" section:
-
- Name Program Name U/D FullScr IO-Red. Multi
- X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
- Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
-
-
-NetBSD Notes:
-=============
-
-Starting at version 0.9.2, U-Boot supports NetBSD both as host
-(build U-Boot) and target system (boots NetBSD/mpc8xx).
-
-Building requires a cross environment; it is known to work on
-NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
-need gmake since the Makefiles are not compatible with BSD make).
-Note that the cross-powerpc package does not install include files;
-attempting to build U-Boot will fail because <machine/ansi.h> is
-missing. This file has to be installed and patched manually:
-
- # cd /usr/pkg/cross/powerpc-netbsd/include
- # mkdir powerpc
- # ln -s powerpc machine
- # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
- # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
-
-Native builds *don't* work due to incompatibilities between native
-and U-Boot include files.
-
-Booting assumes that (the first part of) the image booted is a
-stage-2 loader which in turn loads and then invokes the kernel
-proper. Loader sources will eventually appear in the NetBSD source
-tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
-meantime, send mail to bruno@exet-ag.de and/or wd@denx.de for
-details.
-
-
-Implementation Internals:
-=========================
-
-The following is not intended to be a complete description of every
-implementation detail. However, it should help to understand the
-inner workings of U-Boot and make it easier to port it to custom
-hardware.
-
-
-Initial Stack, Global Data:
----------------------------
-
-The implementation of U-Boot is complicated by the fact that U-Boot
-starts running out of ROM (flash memory), usually without access to
-system RAM (because the memory controller is not initialized yet).
-This means that we don't have writable Data or BSS segments, and BSS
-is not initialized as zero. To be able to get a C environment working
-at all, we have to allocate at least a minimal stack. Implementation
-options for this are defined and restricted by the CPU used: Some CPU
-models provide on-chip memory (like the IMMR area on MPC8xx and
-MPC826x processors), on others (parts of) the data cache can be
-locked as (mis-) used as memory, etc.
-
- Chris Hallinan posted a good summary of these issues to the
- u-boot-users mailing list:
-
- Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
- From: "Chris Hallinan" <clh@net1plus.com>
- Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
- ...
-
- Correct me if I'm wrong, folks, but the way I understand it
- is this: Using DCACHE as initial RAM for Stack, etc, does not
- require any physical RAM backing up the cache. The cleverness
- is that the cache is being used as a temporary supply of
- necessary storage before the SDRAM controller is setup. It's
- beyond the scope of this list to expain the details, but you
- can see how this works by studying the cache architecture and
- operation in the architecture and processor-specific manuals.
-
- OCM is On Chip Memory, which I believe the 405GP has 4K. It
- is another option for the system designer to use as an
- initial stack/ram area prior to SDRAM being available. Either
- option should work for you. Using CS 4 should be fine if your
- board designers haven't used it for something that would
- cause you grief during the initial boot! It is frequently not
- used.
-
- CFG_INIT_RAM_ADDR should be somewhere that won't interfere
- with your processor/board/system design. The default value
- you will find in any recent u-boot distribution in
- Walnut405.h should work for you. I'd set it to a value larger
- than your SDRAM module. If you have a 64MB SDRAM module, set
- it above 400_0000. Just make sure your board has no resources
- that are supposed to respond to that address! That code in
- start.S has been around a while and should work as is when
- you get the config right.
-
- -Chris Hallinan
- DS4.COM, Inc.
-
-It is essential to remember this, since it has some impact on the C
-code for the initialization procedures:
-
-* Initialized global data (data segment) is read-only. Do not attempt
- to write it.
-
-* Do not use any unitialized global data (or implicitely initialized
- as zero data - BSS segment) at all - this is undefined, initiali-
- zation is performed later (when relocating to RAM).
-
-* Stack space is very limited. Avoid big data buffers or things like
- that.
-
-Having only the stack as writable memory limits means we cannot use
-normal global data to share information beween the code. But it
-turned out that the implementation of U-Boot can be greatly
-simplified by making a global data structure (gd_t) available to all
-functions. We could pass a pointer to this data as argument to _all_
-functions, but this would bloat the code. Instead we use a feature of
-the GCC compiler (Global Register Variables) to share the data: we
-place a pointer (gd) to the global data into a register which we
-reserve for this purpose.
-
-When choosing a register for such a purpose we are restricted by the
-relevant (E)ABI specifications for the current architecture, and by
-GCC's implementation.
-
-For PowerPC, the following registers have specific use:
- R1: stack pointer
- R2: TOC pointer
- R3-R4: parameter passing and return values
- R5-R10: parameter passing
- R13: small data area pointer
- R30: GOT pointer
- R31: frame pointer
-
- (U-Boot also uses R14 as internal GOT pointer.)
-
- ==> U-Boot will use R29 to hold a pointer to the global data
-
- Note: on PPC, we could use a static initializer (since the
- address of the global data structure is known at compile time),
- but it turned out that reserving a register results in somewhat
- smaller code - although the code savings are not that big (on
- average for all boards 752 bytes for the whole U-Boot image,
- 624 text + 127 data).
-
-On ARM, the following registers are used:
-
- R0: function argument word/integer result
- R1-R3: function argument word
- R9: GOT pointer
- R10: stack limit (used only if stack checking if enabled)
- R11: argument (frame) pointer
- R12: temporary workspace
- R13: stack pointer
- R14: link register
- R15: program counter
-
- ==> U-Boot will use R8 to hold a pointer to the global data
-
-
-Memory Management:
-------------------
-
-U-Boot runs in system state and uses physical addresses, i.e. the
-MMU is not used either for address mapping nor for memory protection.
-
-The available memory is mapped to fixed addresses using the memory
-controller. In this process, a contiguous block is formed for each
-memory type (Flash, SDRAM, SRAM), even when it consists of several
-physical memory banks.
-
-U-Boot is installed in the first 128 kB of the first Flash bank (on
-TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
-booting and sizing and initializing DRAM, the code relocates itself
-to the upper end of DRAM. Immediately below the U-Boot code some
-memory is reserved for use by malloc() [see CFG_MALLOC_LEN
-configuration setting]. Below that, a structure with global Board
-Info data is placed, followed by the stack (growing downward).
-
-Additionally, some exception handler code is copied to the low 8 kB
-of DRAM (0x00000000 ... 0x00001FFF).
-
-So a typical memory configuration with 16 MB of DRAM could look like
-this:
-
- 0x0000 0000 Exception Vector code
- :
- 0x0000 1FFF
- 0x0000 2000 Free for Application Use
- :
- :
-
- :
- :
- 0x00FB FF20 Monitor Stack (Growing downward)
- 0x00FB FFAC Board Info Data and permanent copy of global data
- 0x00FC 0000 Malloc Arena
- :
- 0x00FD FFFF
- 0x00FE 0000 RAM Copy of Monitor Code
- ... eventually: LCD or video framebuffer
- ... eventually: pRAM (Protected RAM - unchanged by reset)
- 0x00FF FFFF [End of RAM]
-
-
-System Initialization:
-----------------------
-
-In the reset configuration, U-Boot starts at the reset entry point
-(on most PowerPC systens at address 0x00000100). Because of the reset
-configuration for CS0# this is a mirror of the onboard Flash memory.
-To be able to re-map memory U-Boot then jumps to its link address.
-To be able to implement the initialization code in C, a (small!)
-initial stack is set up in the internal Dual Ported RAM (in case CPUs
-which provide such a feature like MPC8xx or MPC8260), or in a locked
-part of the data cache. After that, U-Boot initializes the CPU core,
-the caches and the SIU.
-
-Next, all (potentially) available memory banks are mapped using a
-preliminary mapping. For example, we put them on 512 MB boundaries
-(multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
-on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
-programmed for SDRAM access. Using the temporary configuration, a
-simple memory test is run that determines the size of the SDRAM
-banks.
-
-When there is more than one SDRAM bank, and the banks are of
-different size, the largest is mapped first. For equal size, the first
-bank (CS2#) is mapped first. The first mapping is always for address
-0x00000000, with any additional banks following immediately to create
-contiguous memory starting from 0.
-
-Then, the monitor installs itself at the upper end of the SDRAM area
-and allocates memory for use by malloc() and for the global Board
-Info data; also, the exception vector code is copied to the low RAM
-pages, and the final stack is set up.
-
-Only after this relocation will you have a "normal" C environment;
-until that you are restricted in several ways, mostly because you are
-running from ROM, and because the code will have to be relocated to a
-new address in RAM.
-
-
-U-Boot Porting Guide:
-----------------------
+ -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
+ > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
+ > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
+ > examples/uImage.TQM850L
+ Image Name: 2.4.4 kernel for TQM850L
+ Created: Wed Jul 19 02:34:59 2000
+ Image Type: PowerPC Linux Kernel Image (gzip compressed)
+ Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
+ Load Address: 0x00000000
+ Entry Point: 0x00000000
-[Based on messages by Jerry Van Baren in the U-Boot-Users mailing
-list, October 2002]
+ To verify the contents of the image (or check for corruption):
+ -> tools/mkimage -l examples/uImage.TQM850L
+ Image Name: 2.4.4 kernel for TQM850L
+ Created: Wed Jul 19 02:34:59 2000
+ Image Type: PowerPC Linux Kernel Image (gzip compressed)
+ Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
+ Load Address: 0x00000000
+ Entry Point: 0x00000000
-int main (int argc, char *argv[])
-{
- sighandler_t no_more_time;
+ NOTE: for embedded systems where boot time is critical you can trade
+ speed for memory and install an UNCOMPRESSED image instead: this
+ needs more space in Flash, but boots much faster since it does not
+ need to be uncompressed:
+
+ -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
+ -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
+ > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
+ > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
+ > examples/uImage.TQM850L-uncompressed
+ Image Name: 2.4.4 kernel for TQM850L
+ Created: Wed Jul 19 02:34:59 2000
+ Image Type: PowerPC Linux Kernel Image (uncompressed)
+ Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
+ Load Address: 0x00000000
+ Entry Point: 0x00000000
+
+
+ Similar you can build U-Boot images from a 'ramdisk.image.gz' file
+ when your kernel is intended to use an initial ramdisk:
+
+ -> tools/mkimage -n 'Simple Ramdisk Image' \
+ > -A ppc -O linux -T ramdisk -C gzip \
+ > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
+ Image Name: Simple Ramdisk Image
+ Created: Wed Jan 12 14:01:50 2000
+ Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
+ Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
+ Load Address: 0x00000000
+ Entry Point: 0x00000000
+
+
+ Installing a Linux Image:
+ -------------------------
+
+ To downloading a U-Boot image over the serial (console) interface,
+ you must convert the image to S-Record format:
+
+ objcopy -I binary -O srec examples/image examples/image.srec
+
+ The 'objcopy' does not understand the information in the U-Boot
+ image header, so the resulting S-Record file will be relative to
+ address 0x00000000. To load it to a given address, you need to
+ specify the target address as 'offset' parameter with the 'loads'
+ command.
+
+ Example: install the image to address 0x40100000 (which on the
+ TQM8xxL is in the first Flash bank):
+
+ => erase 40100000 401FFFFF
+
+ .......... done
+ Erased 8 sectors
+
+ => loads 40100000
+ ## Ready for S-Record download ...
+ ~>examples/image.srec
+ 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
+ ...
+ 15989 15990 15991 15992
+ [file transfer complete]
+ [connected]
+ ## Start Addr = 0x00000000
+
+
+ You can check the success of the download using the 'iminfo' command;
+ this includes a checksum verification so you can be sure no data
+ corruption happened:
+
+ => imi 40100000
+
+ ## Checking Image at 40100000 ...
+ Image Name: 2.2.13 for initrd on TQM850L
+ Image Type: PowerPC Linux Kernel Image (gzip compressed)
+ Data Size: 335725 Bytes = 327 kB = 0 MB
+ Load Address: 00000000
+ Entry Point: 0000000c
+ Verifying Checksum ... OK
+
+
+ Boot Linux:
+ -----------
+
+ The "bootm" command is used to boot an application that is stored in
+ memory (RAM or Flash). In case of a Linux kernel image, the contents
+ of the "bootargs" environment variable is passed to the kernel as
+ parameters. You can check and modify this variable using the
+ "printenv" and "setenv" commands:
+
+
+ => printenv bootargs
+ bootargs=root=/dev/ram
+
+ => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
+
+ => printenv bootargs
+ bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
+
+ => bootm 40020000
+ ## Booting Linux kernel at 40020000 ...
+ Image Name: 2.2.13 for NFS on TQM850L
+ Image Type: PowerPC Linux Kernel Image (gzip compressed)
+ Data Size: 381681 Bytes = 372 kB = 0 MB
+ Load Address: 00000000
+ Entry Point: 0000000c
+ Verifying Checksum ... OK
+ Uncompressing Kernel Image ... OK
+ Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
+ Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
+ time_init: decrementer frequency = 187500000/60
+ Calibrating delay loop... 49.77 BogoMIPS
+ Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
+ ...
+
+ If you want to boot a Linux kernel with initial ram disk, you pass
+ the memory addresses of both the kernel and the initrd image (PPBCOOT
+ format!) to the "bootm" command:
+
+ => imi 40100000 40200000
+
+ ## Checking Image at 40100000 ...
+ Image Name: 2.2.13 for initrd on TQM850L
+ Image Type: PowerPC Linux Kernel Image (gzip compressed)
+ Data Size: 335725 Bytes = 327 kB = 0 MB
+ Load Address: 00000000
+ Entry Point: 0000000c
+ Verifying Checksum ... OK
+
+ ## Checking Image at 40200000 ...
+ Image Name: Simple Ramdisk Image
+ Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
+ Data Size: 566530 Bytes = 553 kB = 0 MB
+ Load Address: 00000000
+ Entry Point: 00000000
+ Verifying Checksum ... OK
+
+ => bootm 40100000 40200000
+ ## Booting Linux kernel at 40100000 ...
+ Image Name: 2.2.13 for initrd on TQM850L
+ Image Type: PowerPC Linux Kernel Image (gzip compressed)
+ Data Size: 335725 Bytes = 327 kB = 0 MB
+ Load Address: 00000000
+ Entry Point: 0000000c
+ Verifying Checksum ... OK
+ Uncompressing Kernel Image ... OK
+ ## Loading RAMDisk Image at 40200000 ...
+ Image Name: Simple Ramdisk Image
+ Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
+ Data Size: 566530 Bytes = 553 kB = 0 MB
+ Load Address: 00000000
+ Entry Point: 00000000
+ Verifying Checksum ... OK
+ Loading Ramdisk ... OK
+ Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
+ Boot arguments: root=/dev/ram
+ time_init: decrementer frequency = 187500000/60
+ Calibrating delay loop... 49.77 BogoMIPS
+ ...
+ RAMDISK: Compressed image found at block 0
+ VFS: Mounted root (ext2 filesystem).
+
+ bash#
+
+ More About U-Boot Image Types:
+ ------------------------------
+
+ U-Boot supports the following image types:
+
+ "Standalone Programs" are directly runnable in the environment
+ provided by U-Boot; it is expected that (if they behave
+ well) you can continue to work in U-Boot after return from
+ the Standalone Program.
+ "OS Kernel Images" are usually images of some Embedded OS which
+ will take over control completely. Usually these programs
+ will install their own set of exception handlers, device
+ drivers, set up the MMU, etc. - this means, that you cannot
+ expect to re-enter U-Boot except by resetting the CPU.
+ "RAMDisk Images" are more or less just data blocks, and their
+ parameters (address, size) are passed to an OS kernel that is
+ being started.
+ "Multi-File Images" contain several images, typically an OS
+ (Linux) kernel image and one or more data images like
+ RAMDisks. This construct is useful for instance when you want
+ to boot over the network using BOOTP etc., where the boot
+ server provides just a single image file, but you want to get
+ for instance an OS kernel and a RAMDisk image.
+
+ "Multi-File Images" start with a list of image sizes, each
+ image size (in bytes) specified by an "uint32_t" in network
+ byte order. This list is terminated by an "(uint32_t)0".
+ Immediately after the terminating 0 follow the images, one by
+ one, all aligned on "uint32_t" boundaries (size rounded up to
+ a multiple of 4 bytes).
+
+ "Firmware Images" are binary images containing firmware (like
+ U-Boot or FPGA images) which usually will be programmed to
+ flash memory.
+
+ "Script files" are command sequences that will be executed by
+ U-Boot's command interpreter; this feature is especially
+ useful when you configure U-Boot to use a real shell (hush)
+ as command interpreter.
+
+
+ Standalone HOWTO:
+ =================
+
+ One of the features of U-Boot is that you can dynamically load and
+ run "standalone" applications, which can use some resources of
+ U-Boot like console I/O functions or interrupt services.
+
+ Two simple examples are included with the sources:
+
+ "Hello World" Demo:
+ -------------------
+
+ 'examples/hello_world.c' contains a small "Hello World" Demo
+ application; it is automatically compiled when you build U-Boot.
+ It's configured to run at address 0x00040004, so you can play with it
+ like that:
+
+ => loads
+ ## Ready for S-Record download ...
+ ~>examples/hello_world.srec
+ 1 2 3 4 5 6 7 8 9 10 11 ...
+ [file transfer complete]
+ [connected]
+ ## Start Addr = 0x00040004
+
+ => go 40004 Hello World! This is a test.
+ ## Starting application at 0x00040004 ...
+ Hello World
+ argc = 7
+ argv[0] = "40004"
+ argv[1] = "Hello"
+ argv[2] = "World!"
+ argv[3] = "This"
+ argv[4] = "is"
+ argv[5] = "a"
+ argv[6] = "test."
+ argv[7] = "<NULL>"
+ Hit any key to exit ...
+
+ ## Application terminated, rc = 0x0
+
+ Another example, which demonstrates how to register a CPM interrupt
+ handler with the U-Boot code, can be found in 'examples/timer.c'.
+ Here, a CPM timer is set up to generate an interrupt every second.
+ The interrupt service routine is trivial, just printing a '.'
+ character, but this is just a demo program. The application can be
+ controlled by the following keys:
+
+ ? - print current values og the CPM Timer registers
+ b - enable interrupts and start timer
+ e - stop timer and disable interrupts
+ q - quit application
+
+ => loads
+ ## Ready for S-Record download ...
+ ~>examples/timer.srec
+ 1 2 3 4 5 6 7 8 9 10 11 ...
+ [file transfer complete]
+ [connected]
+ ## Start Addr = 0x00040004
+
+ => go 40004
+ ## Starting application at 0x00040004 ...
+ TIMERS=0xfff00980
+ Using timer 1
+ tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
+
+ Hit 'b':
+ [q, b, e, ?] Set interval 1000000 us
+ Enabling timer
+ Hit '?':
+ [q, b, e, ?] ........
+ tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
+ Hit '?':
+ [q, b, e, ?] .
+ tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
+ Hit '?':
+ [q, b, e, ?] .
+ tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
+ Hit '?':
+ [q, b, e, ?] .
+ tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
+ Hit 'e':
+ [q, b, e, ?] ...Stopping timer
+ Hit 'q':
+ [q, b, e, ?] ## Application terminated, rc = 0x0
+
+
+ Minicom warning:
+ ================
+
+ Over time, many people have reported problems when trying to use the
+ "minicom" terminal emulation program for serial download. I (wd)
+ consider minicom to be broken, and recommend not to use it. Under
+ Unix, I recommend to use C-Kermit for general purpose use (and
+ especially for kermit binary protocol download ("loadb" command), and
+ use "cu" for S-Record download ("loads" command).
+
+ Nevertheless, if you absolutely want to use it try adding this
+ configuration to your "File transfer protocols" section:
+
+ Name Program Name U/D FullScr IO-Red. Multi
+ X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
+ Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
+
+
+ NetBSD Notes:
+ =============
+
+ Starting at version 0.9.2, U-Boot supports NetBSD both as host
+ (build U-Boot) and target system (boots NetBSD/mpc8xx).
+
+ Building requires a cross environment; it is known to work on
+ NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
+ need gmake since the Makefiles are not compatible with BSD make).
+ Note that the cross-powerpc package does not install include files;
+ attempting to build U-Boot will fail because <machine/ansi.h> is
+ missing. This file has to be installed and patched manually:
+
+ # cd /usr/pkg/cross/powerpc-netbsd/include
+ # mkdir powerpc
+ # ln -s powerpc machine
+ # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
+ # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
+
+ Native builds *don't* work due to incompatibilities between native
+ and U-Boot include files.
+
+ Booting assumes that (the first part of) the image booted is a
+ stage-2 loader which in turn loads and then invokes the kernel
+ proper. Loader sources will eventually appear in the NetBSD source
+ tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
+ meantime, send mail to bruno@exet-ag.de and/or wd@denx.de for
+ details.
+
+
+ Implementation Internals:
+ =========================
+
+ The following is not intended to be a complete description of every
+ implementation detail. However, it should help to understand the
+ inner workings of U-Boot and make it easier to port it to custom
+ hardware.
+
+
+ Initial Stack, Global Data:
+ ---------------------------
+
+ The implementation of U-Boot is complicated by the fact that U-Boot
+ starts running out of ROM (flash memory), usually without access to
+ system RAM (because the memory controller is not initialized yet).
+ This means that we don't have writable Data or BSS segments, and BSS
+ is not initialized as zero. To be able to get a C environment working
+ at all, we have to allocate at least a minimal stack. Implementation
+ options for this are defined and restricted by the CPU used: Some CPU
+ models provide on-chip memory (like the IMMR area on MPC8xx and
+ MPC826x processors), on others (parts of) the data cache can be
+ locked as (mis-) used as memory, etc.
+
+ Chris Hallinan posted a good summary of these issues to the
+ u-boot-users mailing list:
+
+ Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
+ From: "Chris Hallinan" <clh@net1plus.com>
+ Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
+ ...
+
+ Correct me if I'm wrong, folks, but the way I understand it
+ is this: Using DCACHE as initial RAM for Stack, etc, does not
+ require any physical RAM backing up the cache. The cleverness
+ is that the cache is being used as a temporary supply of
+ necessary storage before the SDRAM controller is setup. It's
+ beyond the scope of this list to expain the details, but you
+ can see how this works by studying the cache architecture and
+ operation in the architecture and processor-specific manuals.
+
+ OCM is On Chip Memory, which I believe the 405GP has 4K. It
+ is another option for the system designer to use as an
+ initial stack/ram area prior to SDRAM being available. Either
+ option should work for you. Using CS 4 should be fine if your
+ board designers haven't used it for something that would
+ cause you grief during the initial boot! It is frequently not
+ used.
+
+ CFG_INIT_RAM_ADDR should be somewhere that won't interfere
+ with your processor/board/system design. The default value
+ you will find in any recent u-boot distribution in
+ Walnut405.h should work for you. I'd set it to a value larger
+ than your SDRAM module. If you have a 64MB SDRAM module, set
+ it above 400_0000. Just make sure your board has no resources
+ that are supposed to respond to that address! That code in
+ start.S has been around a while and should work as is when
+ you get the config right.
+
+ -Chris Hallinan
+ DS4.COM, Inc.
+
+ It is essential to remember this, since it has some impact on the C
+ code for the initialization procedures:
+
+ * Initialized global data (data segment) is read-only. Do not attempt
+ to write it.
+
+ * Do not use any unitialized global data (or implicitely initialized
+ as zero data - BSS segment) at all - this is undefined, initiali-
+ zation is performed later (when relocating to RAM).
+
+ * Stack space is very limited. Avoid big data buffers or things like
+ that.
+
+ Having only the stack as writable memory limits means we cannot use
+ normal global data to share information beween the code. But it
+ turned out that the implementation of U-Boot can be greatly
+ simplified by making a global data structure (gd_t) available to all
+ functions. We could pass a pointer to this data as argument to _all_
+ functions, but this would bloat the code. Instead we use a feature of
+ the GCC compiler (Global Register Variables) to share the data: we
+ place a pointer (gd) to the global data into a register which we
+ reserve for this purpose.
+
+ When choosing a register for such a purpose we are restricted by the
+ relevant (E)ABI specifications for the current architecture, and by
+ GCC's implementation.
+
+ For PowerPC, the following registers have specific use:
+ R1: stack pointer
+ R2: TOC pointer
+ R3-R4: parameter passing and return values
+ R5-R10: parameter passing
+ R13: small data area pointer
+ R30: GOT pointer
+ R31: frame pointer
+
+ (U-Boot also uses R14 as internal GOT pointer.)
+
+ ==> U-Boot will use R29 to hold a pointer to the global data
+
+ Note: on PPC, we could use a static initializer (since the
+ address of the global data structure is known at compile time),
+ but it turned out that reserving a register results in somewhat
+ smaller code - although the code savings are not that big (on
+ average for all boards 752 bytes for the whole U-Boot image,
+ 624 text + 127 data).
+
+ On ARM, the following registers are used:
+
+ R0: function argument word/integer result
+ R1-R3: function argument word
+ R9: GOT pointer
+ R10: stack limit (used only if stack checking if enabled)
+ R11: argument (frame) pointer
+ R12: temporary workspace
+ R13: stack pointer
+ R14: link register
+ R15: program counter
+
+ ==> U-Boot will use R8 to hold a pointer to the global data
+
+
+ Memory Management:
+ ------------------
+
+ U-Boot runs in system state and uses physical addresses, i.e. the
+ MMU is not used either for address mapping nor for memory protection.
+
+ The available memory is mapped to fixed addresses using the memory
+ controller. In this process, a contiguous block is formed for each
+ memory type (Flash, SDRAM, SRAM), even when it consists of several
+ physical memory banks.
+
+ U-Boot is installed in the first 128 kB of the first Flash bank (on
+ TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
+ booting and sizing and initializing DRAM, the code relocates itself
+ to the upper end of DRAM. Immediately below the U-Boot code some
+ memory is reserved for use by malloc() [see CFG_MALLOC_LEN
+ configuration setting]. Below that, a structure with global Board
+ Info data is placed, followed by the stack (growing downward).
+
+ Additionally, some exception handler code is copied to the low 8 kB
+ of DRAM (0x00000000 ... 0x00001FFF).
+
+ So a typical memory configuration with 16 MB of DRAM could look like
+ this:
+
+ 0x0000 0000 Exception Vector code
+ :
+ 0x0000 1FFF
+ 0x0000 2000 Free for Application Use
+ :
+ :
+
+ :
+ :
+ 0x00FB FF20 Monitor Stack (Growing downward)
+ 0x00FB FFAC Board Info Data and permanent copy of global data
+ 0x00FC 0000 Malloc Arena
+ :
+ 0x00FD FFFF
+ 0x00FE 0000 RAM Copy of Monitor Code
+ ... eventually: LCD or video framebuffer
+ ... eventually: pRAM (Protected RAM - unchanged by reset)
+ 0x00FF FFFF [End of RAM]
+
+
+ System Initialization:
+ ----------------------
+
+ In the reset configuration, U-Boot starts at the reset entry point
+ (on most PowerPC systens at address 0x00000100). Because of the reset
+ configuration for CS0# this is a mirror of the onboard Flash memory.
+ To be able to re-map memory U-Boot then jumps to its link address.
+ To be able to implement the initialization code in C, a (small!)
+ initial stack is set up in the internal Dual Ported RAM (in case CPUs
+ which provide such a feature like MPC8xx or MPC8260), or in a locked
+ part of the data cache. After that, U-Boot initializes the CPU core,
+ the caches and the SIU.
+
+ Next, all (potentially) available memory banks are mapped using a
+ preliminary mapping. For example, we put them on 512 MB boundaries
+ (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
+ on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
+ programmed for SDRAM access. Using the temporary configuration, a
+ simple memory test is run that determines the size of the SDRAM
+ banks.
+
+ When there is more than one SDRAM bank, and the banks are of
+ different size, the largest is mapped first. For equal size, the first
+ bank (CS2#) is mapped first. The first mapping is always for address
+ 0x00000000, with any additional banks following immediately to create
+ contiguous memory starting from 0.
+
+ Then, the monitor installs itself at the upper end of the SDRAM area
+ and allocates memory for use by malloc() and for the global Board
+ Info data; also, the exception vector code is copied to the low RAM
+ pages, and the final stack is set up.
+
+ Only after this relocation will you have a "normal" C environment;
+ until that you are restricted in several ways, mostly because you are
+ running from ROM, and because the code will have to be relocated to a
+ new address in RAM.
+
+
+ U-Boot Porting Guide:
+ ----------------------
+
+ [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
+ list, October 2002]
+
+
+ int main (int argc, char *argv[])
+ {
+ sighandler_t no_more_time;
+
+ signal (SIGALRM, no_more_time);
+ alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
+
+ if (available_money > available_manpower) {
+ pay consultant to port U-Boot;
+ return 0;
+ }
+
+ Download latest U-Boot source;
+
+ Subscribe to u-boot-users mailing list;
+
+ if (clueless) {
+ email ("Hi, I am new to U-Boot, how do I get started?");
+ }
+
+ while (learning) {
+ Read the README file in the top level directory;
+ Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
+ Read the source, Luke;
+ }
+
+ if (available_money > toLocalCurrency ($2500)) {
+ Buy a BDI2000;
+ } else {
+ Add a lot of aggravation and time;
+ }
+
+ Create your own board support subdirectory;
+
+ Create your own board config file;
+
+ while (!running) {
+ do {
+ Add / modify source code;
+ } until (compiles);
+ Debug;
+ if (clueless)
+ email ("Hi, I am having problems...");
+ }
+ Send patch file to Wolfgang;
- signal (SIGALRM, no_more_time);
- alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
-
- if (available_money > available_manpower) {
- pay consultant to port U-Boot;
return 0;
}
- Download latest U-Boot source;
-
- Subscribe to u-boot-users mailing list;
-
- if (clueless) {
- email ("Hi, I am new to U-Boot, how do I get started?");
+ void no_more_time (int sig)
+ {
+ hire_a_guru();
}
- while (learning) {
- Read the README file in the top level directory;
- Read http://www.denx.de/re/DPLG.html
- Read the source, Luke;
- }
-
- if (available_money > toLocalCurrency ($2500)) {
- Buy a BDI2000;
- } else {
- Add a lot of aggravation and time;
- }
-
- Create your own board support subdirectory;
-
- Create your own board config file;
-
- while (!running) {
- do {
- Add / modify source code;
- } until (compiles);
- Debug;
- if (clueless)
- email ("Hi, I am having problems...");
- }
- Send patch file to Wolfgang;
-
- return 0;
-}
-
-void no_more_time (int sig)
-{
- hire_a_guru();
-}
+ Coding Standards:
+ -----------------
-Coding Standards:
------------------
+ All contributions to U-Boot should conform to the Linux kernel
+ coding style; see the file "Documentation/CodingStyle" in your Linux
+ kernel source directory.
-All contributions to U-Boot should conform to the Linux kernel
-coding style; see the file "Documentation/CodingStyle" in your Linux
-kernel source directory.
+ Please note that U-Boot is implemented in C (and to some small parts
+ in Assembler); no C++ is used, so please do not use C++ style
+ comments (//) in your code.
-Please note that U-Boot is implemented in C (and to some small parts
-in Assembler); no C++ is used, so please do not use C++ style
-comments (//) in your code.
+ Please also stick to the following formatting rules:
+ - remove any trailing white space
+ - use TAB characters for indentation, not spaces
+ - make sure NOT to use DOS '\r\n' line feeds
+ - do not add more than 2 empty lines to source files
+ - do not add trailing empty lines to source files
-Submissions which do not conform to the standards may be returned
-with a request to reformat the changes.
+ Submissions which do not conform to the standards may be returned
+ with a request to reformat the changes.
-Submitting Patches:
--------------------
+ Submitting Patches:
+ -------------------
-Since the number of patches for U-Boot is growing, we need to
-establish some rules. Submissions which do not conform to these rules
-may be rejected, even when they contain important and valuable stuff.
+ Since the number of patches for U-Boot is growing, we need to
+ establish some rules. Submissions which do not conform to these rules
+ may be rejected, even when they contain important and valuable stuff.
-When you send a patch, please include the following information with
-it:
+ When you send a patch, please include the following information with
+ it:
-* For bug fixes: a description of the bug and how your patch fixes
- this bug. Please try to include a way of demonstrating that the
- patch actually fixes something.
+ * For bug fixes: a description of the bug and how your patch fixes
+ this bug. Please try to include a way of demonstrating that the
+ patch actually fixes something.
-* For new features: a description of the feature and your
- implementation.
+ * For new features: a description of the feature and your
+ implementation.
-* A CHANGELOG entry as plaintext (separate from the patch)
+ * A CHANGELOG entry as plaintext (separate from the patch)
-* For major contributions, your entry to the CREDITS file
+ * For major contributions, your entry to the CREDITS file
-* When you add support for a new board, don't forget to add this
- board to the MAKEALL script, too.
+ * When you add support for a new board, don't forget to add this
+ board to the MAKEALL script, too.
-* If your patch adds new configuration options, don't forget to
- document these in the README file.
+ * If your patch adds new configuration options, don't forget to
+ document these in the README file.
-* The patch itself. If you are accessing the CVS repository use "cvs
- update; cvs diff -puRN"; else, use "diff -purN OLD NEW". If your
- version of diff does not support these options, then get the latest
- version of GNU diff.
+ * The patch itself. If you are accessing the CVS repository use "cvs
+ update; cvs diff -puRN"; else, use "diff -purN OLD NEW". If your
+ version of diff does not support these options, then get the latest
+ version of GNU diff.
- The current directory when running this command shall be the top
- level directory of the U-Boot source tree, or it's parent directory
- (i. e. please make sure that your patch includes sufficient
- directory information for the affected files).
+ The current directory when running this command shall be the top
+ level directory of the U-Boot source tree, or it's parent directory
+ (i. e. please make sure that your patch includes sufficient
+ directory information for the affected files).
- We accept patches as plain text, MIME attachments or as uuencoded
- gzipped text.
+ We accept patches as plain text, MIME attachments or as uuencoded
+ gzipped text.
-* If one logical set of modifications affects or creates several
- files, all these changes shall be submitted in a SINGLE patch file.
+ * If one logical set of modifications affects or creates several
+ files, all these changes shall be submitted in a SINGLE patch file.
-* Changesets that contain different, unrelated modifications shall be
- submitted as SEPARATE patches, one patch per changeset.
+ * Changesets that contain different, unrelated modifications shall be
+ submitted as SEPARATE patches, one patch per changeset.
-Notes:
+ Notes:
-* Before sending the patch, run the MAKEALL script on your patched
- source tree and make sure that no errors or warnings are reported
- for any of the boards.
+ * Before sending the patch, run the MAKEALL script on your patched
+ source tree and make sure that no errors or warnings are reported
+ for any of the boards.
-* Keep your modifications to the necessary minimum: A patch
- containing several unrelated changes or arbitrary reformats will be
- returned with a request to re-formatting / split it.
+ * Keep your modifications to the necessary minimum: A patch
+ containing several unrelated changes or arbitrary reformats will be
+ returned with a request to re-formatting / split it.
-* If you modify existing code, make sure that your new code does not
- add to the memory footprint of the code ;-) Small is beautiful!
- When adding new features, these should compile conditionally only
- (using #ifdef), and the resulting code with the new feature
- disabled must not need more memory than the old code without your
- modification.
+ * If you modify existing code, make sure that your new code does not
+ add to the memory footprint of the code ;-) Small is beautiful!
+ When adding new features, these should compile conditionally only
+ (using #ifdef), and the resulting code with the new feature
+ disabled must not need more memory than the old code without your
+ modification.
projects / u-boot / blobdiff