#
-# (C) Copyright 2000 - 2011
+# (C) Copyright 2000 - 2012
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
XWAY SoCs for booting from NOR flash. The U-Boot image needs to
be swapped if a flash programmer is used.
+- ARM options:
+ CONFIG_SYS_EXCEPTION_VECTORS_HIGH
+
+ Select high exception vectors of the ARM core, e.g., do not
+ clear the V bit of the c1 register of CP15.
+
- Linux Kernel Interface:
CONFIG_CLOCKS_IN_MHZ
CONFIG_CFB_CONSOLE
Enables console device for a color framebuffer. Needs following
- defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
+ defines (cf. smiLynxEM, i8042)
VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
(default big endian)
VIDEO_HW_RECTFILL graphic chip supports
'Sane' compilers will generate smaller code if
CONFIG_PRE_CON_BUF_SZ is a power of 2
+- Pre-console putc():
+ Prior to the console being initialised, console output is
+ normally silently discarded. This can be annoying if a
+ panic() happens in this time.
+
+ If the CONFIG_PRE_CONSOLE_PUTC option is defined, then
+ U-Boot will call board_pre_console_putc() for each output
+ character in this case, This function should try to output
+ the character if possible, perhaps on all available UARTs
+ (it will need to do this directly, since the console code
+ is not functional yet). Note that if the panic happens
+ early enough, then it is possible that board_init_f()
+ (or even arch_cpu_init() on ARM) has not been called yet.
+ You should init all clocks, GPIOs, etc. that are needed
+ to get the character out. Baud rates will need to default
+ to something sensible.
+
+- Safe printf() functions
+ Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
+ the printf() functions. These are defined in
+ include/vsprintf.h and include snprintf(), vsnprintf() and
+ so on. Code size increase is approximately 300-500 bytes.
+ If this option is not given then these functions will
+ silently discard their buffer size argument - this means
+ you are not getting any overflow checking in this case.
+
- Boot Delay: CONFIG_BOOTDELAY - in seconds
Delay before automatically booting the default image;
set to -1 to disable autoboot.
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
+ CONFIG_CMD_SF * Read/write/erase SPI NOR flash
CONFIG_CMD_SHA1SUM print sha1 memory digest
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
- CONFIG_RTC_MC13783 - use MC13783 RTC
+ CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
CONFIG_RTC_MC146818 - use MC146818 RTC
CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
- NETWORK Support (PCI):
CONFIG_E1000
- Support for Intel 8254x gigabit chips.
+ Support for Intel 8254x/8257x gigabit chips.
+
+ CONFIG_E1000_SPI
+ Utility code for direct access to the SPI bus on Intel 8257x.
+ This does not do anything useful unless you set at least one
+ of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
+
+ CONFIG_E1000_SPI_GENERIC
+ Allow generic access to the SPI bus on the Intel 8257x, for
+ example with the "sspi" command.
+
+ CONFIG_CMD_E1000
+ Management command for E1000 devices. When used on devices
+ with SPI support you can reprogram the EEPROM from U-Boot.
CONFIG_E1000_FALLBACK_MAC
default MAC for empty EEPROM after production.
If this defined, the driver is quiet.
The driver doen't show link status messages.
+ CONFIG_CALXEDA_XGMAC
+ Support for the Calxeda XGMAC device
+
CONFIG_DRIVER_LAN91C96
Support for SMSC's LAN91C96 chips.
Define this to use i/o functions instead of macros
(some hardware wont work with macros)
+ CONFIG_DRIVER_TI_EMAC
+ Support for davinci emac
+
+ CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
+ Define this if you have more then 3 PHYs.
+
CONFIG_FTGMAC100
Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
CONFIG_SH_ETHER_CACHE_WRITEBACK
If this option is set, the driver enables cache flush.
+- TPM Support:
+ CONFIG_GENERIC_LPC_TPM
+ Support for generic parallel port TPM devices. Only one device
+ per system is supported at this time.
+
+ CONFIG_TPM_TIS_BASE_ADDRESS
+ Base address where the generic TPM device is mapped
+ to. Contemporary x86 systems usually map it at
+ 0xfed40000.
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405, MPC5200); define
for your device
- CONFIG_USBD_PRODUCTID 0xFFFF
+- ULPI Layer Support:
+ The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
+ the generic ULPI layer. The generic layer accesses the ULPI PHY
+ via the platform viewport, so you need both the genric layer and
+ the viewport enabled. Currently only Chipidea/ARC based
+ viewport is supported.
+ To enable the ULPI layer support, define CONFIG_USB_ULPI and
+ CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
- MMC Support:
The MMC controller on the Intel PXA is supported. To
Define a default value for the IP address to use for
the default Ethernet interface, in case this is not
determined through e.g. bootp.
+ (Environment variable "ipaddr")
- Server IP address:
CONFIG_SERVERIP
Defines a default value for the IP address of a TFTP
server to contact when using the "tftboot" command.
+ (Environment variable "serverip")
CONFIG_KEEP_SERVERADDR
Keeps the server's MAC address, in the env 'serveraddr'
for passing to bootargs (like Linux's netconsole option)
+- Gateway IP address:
+ CONFIG_GATEWAYIP
+
+ Defines a default value for the IP address of the
+ default router where packets to other networks are
+ sent to.
+ (Environment variable "gatewayip")
+
+- Subnet mask:
+ CONFIG_NETMASK
+
+ Defines a default value for the subnet mask (or
+ routing prefix) which is used to determine if an IP
+ address belongs to the local subnet or needs to be
+ forwarded through a router.
+ (Environment variable "netmask")
+
- Multicast TFTP Mode:
CONFIG_MCAST_TFTP
CONFIG_MXC_SPI
Enables the driver for the SPI controllers on i.MX and MXC
- SoCs. Currently only i.MX31 is supported.
+ SoCs. Currently i.MX31/35/51 are supported.
- FPGA Support: CONFIG_FPGA
allows to read/write in Dataflash via the standard
commands cp, md...
+- Serial Flash support
+ CONFIG_CMD_SF
+
+ Defining this option enables SPI flash commands
+ 'sf probe/read/write/erase/update'.
+
+ Usage requires an initial 'probe' to define the serial
+ flash parameters, followed by read/write/erase/update
+ commands.
+
+ The following defaults may be provided by the platform
+ to handle the common case when only a single serial
+ flash is present on the system.
+
+ CONFIG_SF_DEFAULT_BUS Bus identifier
+ CONFIG_SF_DEFAULT_CS Chip-select
+ CONFIG_SF_DEFAULT_MODE (see include/spi.h)
+ CONFIG_SF_DEFAULT_SPEED in Hz
+
- SystemACE Support:
CONFIG_SYSTEMACE
See also: doc/README.Modem
+Board initialization settings:
+------------------------------
+
+During Initialization u-boot calls a number of board specific functions
+to allow the preparation of board specific prerequisites, e.g. pin setup
+before drivers are initialized. To enable these callbacks the
+following configuration macros have to be defined. Currently this is
+architecture specific, so please check arch/your_architecture/lib/board.c
+typically in board_init_f() and board_init_r().
+
+- CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
+- CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
+- CONFIG_BOARD_LATE_INIT: Call board_late_init()
+- CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
Configuration Settings:
-----------------------
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
+- CONFIG_SYS_NAND_HW_ECC_OOBFIRST
+ define this, if you want to read first the oob data
+ and then the data. This is used for example on
+ davinci plattforms.
+
- CONFIG_USE_ARCH_MEMCPY
CONFIG_USE_ARCH_MEMSET
If these options are used a optimized version of memcpy/memset will
be used if available. These functions may be faster under some
conditions but may increase the binary size.
+Freescale QE/FMAN Firmware Support:
+-----------------------------------
+
+The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
+loading of "firmware", which is encoded in the QE firmware binary format.
+This firmware often needs to be loaded during U-Boot booting, so macros
+are used to identify the storage device (NOR flash, SPI, etc) and the address
+within that device.
+
+- CONFIG_SYS_QE_FMAN_FW_ADDR
+ The address in the storage device where the firmware is located. The
+ meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+ is also specified.
+
+- CONFIG_SYS_QE_FMAN_FW_LENGTH
+ The maximum possible size of the firmware. The firmware binary format
+ has a field that specifies the actual size of the firmware, but it
+ might not be possible to read any part of the firmware unless some
+ local storage is allocated to hold the entire firmware first.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_NOR
+ Specifies that QE/FMAN firmware is located in NOR flash, mapped as
+ normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
+ virtual address in NOR flash.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_NAND
+ Specifies that QE/FMAN firmware is located in NAND flash.
+ CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_MMC
+ Specifies that QE/FMAN firmware is located on the primary SD/MMC
+ device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
+ Specifies that QE/FMAN firmware is located on the primary SPI
+ device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+
+
Building the Software:
======================