efi_loader: implement event groups

[u-boot] / README

diff --git a/README b/README
index 48db0cb45c942cd5205468a2aac734cd522b186f..ed79298fd4ea9f09911ac5bbc7860da870d9055a 100644 (file)
--- a/README
+++ b/README
@@ -713,17 +713,6 @@ The following options need to be configured:
                as a convenience, when switching between booting from
                RAM and NFS.
 
-- Bootcount:
-               CONFIG_BOOTCOUNT_ENV
-               If no softreset save registers are found on the hardware
-               "bootcount" is stored in the environment. To prevent a
-               saveenv on all reboots, the environment variable
-               "upgrade_available" is used. If "upgrade_available" is
-               0, "bootcount" is always 0, if "upgrade_available" is
-               1 "bootcount" is incremented in the environment.
-               So the Userspace Applikation must set the "upgrade_available"
-               and "bootcount" variable to 0, if a boot was successfully.
-
 - Pre-Boot Commands:
                CONFIG_PREBOOT
 
@@ -1431,10 +1420,6 @@ The following options need to be configured:
                be at least 4MB.
 
 - MII/PHY support:
-               CONFIG_PHY_ADDR
-
-               The address of PHY on MII bus.
-
                CONFIG_PHY_CLOCK_FREQ (ppc4xx)
 
                The clock frequency of the MII bus
@@ -1538,14 +1523,8 @@ The following options need to be configured:
                You can fine tune the DHCP functionality by defining
                CONFIG_BOOTP_* symbols:
 
-               CONFIG_BOOTP_SUBNETMASK
-               CONFIG_BOOTP_GATEWAY
-               CONFIG_BOOTP_HOSTNAME
                CONFIG_BOOTP_NISDOMAIN
-               CONFIG_BOOTP_BOOTPATH
                CONFIG_BOOTP_BOOTFILESIZE
-               CONFIG_BOOTP_DNS
-               CONFIG_BOOTP_DNS2
                CONFIG_BOOTP_SEND_HOSTNAME
                CONFIG_BOOTP_NTPSERVER
                CONFIG_BOOTP_TIMEOFFSET
@@ -1561,15 +1540,6 @@ The following options need to be configured:
                to Link-local IP address configuration if the DHCP server
                is not available.
 
-               CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
-               serverip from a DHCP server, it is possible that more
-               than one DNS serverip is offered to the client.
-               If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
-               serverip will be stored in the additional environment
-               variable "dnsip2". The first DNS serverip is always
-               stored in the variable "dnsip", when CONFIG_BOOTP_DNS
-               is defined.
-
                CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
                to do a dynamic update of a DNS server. To do this, they
                need the hostname of the DHCP requester.
@@ -2182,10 +2152,6 @@ The following options need to be configured:
                #define CONFIG_NFS_TIMEOUT 10000UL
 
 - Command Interpreter:
-               CONFIG_AUTO_COMPLETE
-
-               Enable auto completion of commands using TAB.
-
                CONFIG_SYS_PROMPT_HUSH_PS2
 
                This defines the secondary prompt string, which is
@@ -2214,12 +2180,6 @@ The following options need to be configured:
                symbols.
 
 - Command Line Editing and History:
-               CONFIG_CMDLINE_EDITING
-
-               Enable editing and History functions for interactive
-               command line input operations
-
-- Command Line PS1/PS2 support:
                CONFIG_CMDLINE_PS_SUPPORT
 
                Enable support for changing the command prompt string
@@ -2253,20 +2213,6 @@ The following options need to be configured:
                the environment like the "source" command or the
                boot command first.
 
-               CONFIG_ENV_VARS_UBOOT_CONFIG
-
-               Define this in order to add variables describing the
-               U-Boot build configuration to the default environment.
-               These will be named arch, cpu, board, vendor, and soc.
-
-               Enabling this option will cause the following to be defined:
-
-               - CONFIG_SYS_ARCH
-               - CONFIG_SYS_CPU
-               - CONFIG_SYS_BOARD
-               - CONFIG_SYS_VENDOR
-               - CONFIG_SYS_SOC
-
                CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 
                Define this in order to add variables describing certain
@@ -2317,27 +2263,6 @@ The following options need to be configured:
                A better solution is to properly configure the firewall,
                but sometimes that is not allowed.
 
-- bootcount support:
-               CONFIG_AT91SAM9XE
-               enable special bootcounter support on at91sam9xe based boards.
-               CONFIG_SOC_DA8XX
-               enable special bootcounter support on da850 based boards.
-               CONFIG_BOOTCOUNT_RAM
-               enable support for the bootcounter in RAM
-               CONFIG_BOOTCOUNT_I2C
-               enable support for the bootcounter on an i2c (like RTC) device.
-                       CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
-                       CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
-                                                   the bootcounter.
-                       CONFIG_BOOTCOUNT_ALEN = address len
-               CONFIG_BOOTCOUNT_EXT
-               enable support for the bootcounter in EXT filesystem
-                       CONFIG_SYS_BOOTCOUNT_ADDR = RAM address used for read
-                                                    and write.
-                       CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE = interface
-                       CONFIG_SYS_BOOTCOUNT_EXT_DEVPART = device and part
-                       CONFIG_SYS_BOOTCOUNT_EXT_NAME = filename
-
 - Show boot progress:
                CONFIG_SHOW_BOOT_PROGRESS
 
@@ -2557,12 +2482,6 @@ FIT uImage format:
                kernel. Needed for UBI support.
 
 - UBI support
-               CONFIG_UBI_SILENCE_MSG
-
-               Make the verbose messages from UBI stop printing.  This leaves
-               warnings and errors enabled.
-
-
                CONFIG_MTD_UBI_WL_THRESHOLD
                This parameter defines the maximum difference between the highest
                erase counter value and the lowest erase counter value of eraseblocks
@@ -2624,12 +2543,6 @@ FIT uImage format:
                Enable UBI fastmap debug
                default: 0
 
-- UBIFS support
-               CONFIG_UBIFS_SILENCE_MSG
-
-               Make the verbose messages from UBIFS stop printing.  This leaves
-               warnings and errors enabled.
-
 - SPL framework
                CONFIG_SPL
                Enable building of SPL globally.