configs: clearfog: enable random random MAC address

[u-boot] / README

diff --git a/README b/README
index b227d8e90746b285558e88fde5681f975a931515..ed79298fd4ea9f09911ac5bbc7860da870d9055a 100644 (file)
--- a/README
+++ b/README
@@ -713,17 +713,6 @@ The following options need to be configured:
                as a convenience, when switching between booting from
                RAM and NFS.
 
-- Bootcount:
-               CONFIG_BOOTCOUNT_ENV
-               If no softreset save registers are found on the hardware
-               "bootcount" is stored in the environment. To prevent a
-               saveenv on all reboots, the environment variable
-               "upgrade_available" is used. If "upgrade_available" is
-               0, "bootcount" is always 0, if "upgrade_available" is
-               1 "bootcount" is incremented in the environment.
-               So the Userspace Applikation must set the "upgrade_available"
-               and "bootcount" variable to 0, if a boot was successfully.
-
 - Pre-Boot Commands:
                CONFIG_PREBOOT
 
@@ -1431,10 +1420,6 @@ The following options need to be configured:
                be at least 4MB.
 
 - MII/PHY support:
-               CONFIG_PHY_ADDR
-
-               The address of PHY on MII bus.
-
                CONFIG_PHY_CLOCK_FREQ (ppc4xx)
 
                The clock frequency of the MII bus
@@ -2278,25 +2263,6 @@ The following options need to be configured:
                A better solution is to properly configure the firewall,
                but sometimes that is not allowed.
 
-- bootcount support:
-               CONFIG_AT91SAM9XE
-               enable special bootcounter support on at91sam9xe based boards.
-               CONFIG_BOOTCOUNT_RAM
-               enable support for the bootcounter in RAM
-               CONFIG_BOOTCOUNT_I2C
-               enable support for the bootcounter on an i2c (like RTC) device.
-                       CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
-                       CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
-                                                   the bootcounter.
-                       CONFIG_BOOTCOUNT_ALEN = address len
-               CONFIG_BOOTCOUNT_EXT
-               enable support for the bootcounter in EXT filesystem
-                       CONFIG_SYS_BOOTCOUNT_ADDR = RAM address used for read
-                                                    and write.
-                       CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE = interface
-                       CONFIG_SYS_BOOTCOUNT_EXT_DEVPART = device and part
-                       CONFIG_SYS_BOOTCOUNT_EXT_NAME = filename
-
 - Show boot progress:
                CONFIG_SHOW_BOOT_PROGRESS
 
@@ -2516,12 +2482,6 @@ FIT uImage format:
                kernel. Needed for UBI support.
 
 - UBI support
-               CONFIG_UBI_SILENCE_MSG
-
-               Make the verbose messages from UBI stop printing.  This leaves
-               warnings and errors enabled.
-
-
                CONFIG_MTD_UBI_WL_THRESHOLD
                This parameter defines the maximum difference between the highest
                erase counter value and the lowest erase counter value of eraseblocks
@@ -2583,12 +2543,6 @@ FIT uImage format:
                Enable UBI fastmap debug
                default: 0
 
-- UBIFS support
-               CONFIG_UBIFS_SILENCE_MSG
-
-               Make the verbose messages from UBIFS stop printing.  This leaves
-               warnings and errors enabled.
-
 - SPL framework
                CONFIG_SPL
                Enable building of SPL globally.