CONFIG_ARM_ERRATA_742230
CONFIG_ARM_ERRATA_743622
CONFIG_ARM_ERRATA_751472
- CONFIG_ARM_ERRATA_794072
CONFIG_ARM_ERRATA_761320
+ CONFIG_ARM_ERRATA_773022
+ CONFIG_ARM_ERRATA_774769
+ CONFIG_ARM_ERRATA_794072
If set, the workarounds for these ARM errata are applied early
during U-Boot startup. Note that these options force the
exists, unlike the similar options in the Linux kernel. Do not
set these options unless they apply!
+ COUNTER_FREQUENCY
+ Generic timer clock source frequency.
+
+ COUNTER_FREQUENCY_REAL
+ Generic timer clock source frequency if the real clock is
+ different from COUNTER_FREQUENCY, and can only be determined
+ at run time.
+
NOTE: The following can be machine specific errata. These
do have ability to provide rudimentary version and machine
specific checks, but expect no product checks.
CONFIG_ARM_ERRATA_454179
CONFIG_ARM_ERRATA_621766
CONFIG_ARM_ERRATA_798870
+ CONFIG_ARM_ERRATA_801819
- Tegra SoC options:
CONFIG_TEGRA_SUPPORT_NON_SECURE
- vxWorks boot parameters:
bootvx constructs a valid bootline using the following
- environments variables: bootfile, ipaddr, serverip, hostname.
+ environments variables: bootdev, bootfile, ipaddr, netmask,
+ serverip, gatewayip, hostname, othbootargs.
It loads the vxWorks image pointed bootfile.
- CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
- CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
- CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
- CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
-
- CONFIG_SYS_VXWORKS_ADD_PARAMS
-
- Add it at the end of the bootline. E.g "u=username pw=secret"
-
Note: If a "bootargs" environment is defined, it will overwride
the defaults discussed just above.
define this to a list of base addresses for each (supported)
port. See e.g. include/configs/versatile.h
- CONFIG_PL011_SERIAL_RLCR
-
- Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
- have separate receive and transmit line control registers. Set
- this variable to initialize the extra register.
-
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT
-
- On some platforms (e.g. U8500) U-Boot is loaded by a second stage
- boot loader that has already initialized the UART. Define this
- variable to flush the UART at init time.
-
CONFIG_SERIAL_HW_FLOW_CONTROL
Define this variable to enable hw flow control in serial driver.
bytes are output before the console is initialised, the
earlier bytes are discarded.
+ Note that when printing the buffer a copy is made on the
+ stack so CONFIG_PRE_CON_BUF_SZ must fit on the stack.
+
'Sane' compilers will generate smaller code if
CONFIG_PRE_CON_BUF_SZ is a power of 2
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_DELAY_STR
CONFIG_AUTOBOOT_STOP_STR
- CONFIG_AUTOBOOT_DELAY_STR2
- CONFIG_AUTOBOOT_STOP_STR2
CONFIG_ZERO_BOOTDELAY_CHECK
CONFIG_RESET_TO_RETRY
Monitor commands can be included or excluded
from the build by using the #include files
<config_cmd_all.h> and #undef'ing unwanted
- commands, or using <config_cmd_default.h>
- and augmenting with additional #define's
- for wanted commands.
+ commands, or adding #define's for wanted commands.
The default command configuration includes all commands
except those marked below with a "*".
Management command for E1000 devices. When used on devices
with SPI support you can reprogram the EEPROM from U-Boot.
- CONFIG_E1000_FALLBACK_MAC
- default MAC for empty EEPROM after production.
-
CONFIG_EEPRO100
Support for Intel 82557/82559/82559ER chips.
Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
CONFIG_TPM
Support TPM devices.
- CONFIG_TPM_TIS_I2C
- Support for i2c bus TPM devices. Only one device
+ CONFIG_TPM_TIS_INFINEON
+ Support for Infineon i2c bus TPM devices. Only one device
per system is supported at this time.
- CONFIG_TPM_TIS_I2C_BUS_NUMBER
- Define the the i2c bus number for the TPM device
-
- CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
- Define the TPM's address on the i2c bus
-
CONFIG_TPM_TIS_I2C_BURST_LIMITATION
Define the burst count bytes upper limit
key for the Replay Protection Memory Block partition in eMMC.
- USB Device Firmware Update (DFU) class support:
- CONFIG_DFU_FUNCTION
+ CONFIG_USB_FUNCTION_DFU
This enables the USB portion of the DFU USB class
CONFIG_CMD_DFU
sending again an USB request to the device.
- USB Device Android Fastboot support:
+ CONFIG_USB_FUNCTION_FASTBOOT
+ This enables the USB part of the fastboot gadget
+
CONFIG_CMD_FASTBOOT
This enables the command "fastboot" which enables the Android
fastboot mode for the platform's USB device. Fastboot is a USB
This enables support for booting images which use the Android
image format header.
- CONFIG_USB_FASTBOOT_BUF_ADDR
+ CONFIG_FASTBOOT_BUF_ADDR
The fastboot protocol requires a large memory buffer for
downloads. Define this to the starting RAM address to use for
downloaded images.
- CONFIG_USB_FASTBOOT_BUF_SIZE
+ CONFIG_FASTBOOT_BUF_SIZE
The fastboot protocol requires a large memory buffer for
downloads. This buffer should be as large as possible for a
platform. Define this to the size available RAM for fastboot.
boot. See the documentation file README.video for a
description of this variable.
- CONFIG_VIDEO_VGA
-
- Enable the VGA video / BIOS for x86. The alternative if you
- are using coreboot is to use the coreboot frame buffer
- driver.
-
- Keyboard Support:
CONFIG_KEYBOARD
the console jump but can help speed up operation when scrolling
is slow.
+ CONFIG_LCD_ROTATION
+
+ Sometimes, for example if the display is mounted in portrait
+ mode or even if it's mounted landscape but rotated by 180degree,
+ we need to rotate our content of the display relative to the
+ framebuffer, so that user can read the messages which are
+ printed out.
+ Once CONFIG_LCD_ROTATION is defined, the lcd_console will be
+ initialized with a given rotation from "vl_rot" out of
+ "vidinfo_t" which is provided by the board specific code.
+ The value for vl_rot is coded as following (matching to
+ fbcon=rotate:<n> linux-kernel commandline):
+ 0 = no rotation respectively 0 degree
+ 1 = 90 degree rotation
+ 2 = 180 degree rotation
+ 3 = 270 degree rotation
+
+ If CONFIG_LCD_ROTATION is not defined, the console will be
+ initialized with 0degree rotation.
+
CONFIG_LCD_BMP_RLE8
Support drawing of RLE8-compressed bitmaps on the LCD.
Some PHY like Intel LXT971A need extra delay after
command issued before MII status register can be read
-- Ethernet address:
- CONFIG_ETHADDR
- CONFIG_ETH1ADDR
- CONFIG_ETH2ADDR
- CONFIG_ETH3ADDR
- CONFIG_ETH4ADDR
- CONFIG_ETH5ADDR
-
- Define a default value for Ethernet address to use
- for the respective Ethernet interface, in case this
- is not determined automatically.
-
- IP address:
CONFIG_IPADDR
- drivers/i2c/i2c_mxc.c
- activate this driver with CONFIG_SYS_I2C_MXC
+ - enable bus 1 with CONFIG_SYS_I2C_MXC_I2C1
+ - enable bus 2 with CONFIG_SYS_I2C_MXC_I2C2
+ - enable bus 3 with CONFIG_SYS_I2C_MXC_I2C3
+ - enable bus 4 with CONFIG_SYS_I2C_MXC_I2C4
- define speed for bus 1 with CONFIG_SYS_MXC_I2C1_SPEED
- define slave for bus 1 with CONFIG_SYS_MXC_I2C1_SLAVE
- define speed for bus 2 with CONFIG_SYS_MXC_I2C2_SPEED
- define slave for bus 2 with CONFIG_SYS_MXC_I2C2_SLAVE
- define speed for bus 3 with CONFIG_SYS_MXC_I2C3_SPEED
- define slave for bus 3 with CONFIG_SYS_MXC_I2C3_SLAVE
+ - define speed for bus 4 with CONFIG_SYS_MXC_I2C4_SPEED
+ - define slave for bus 4 with CONFIG_SYS_MXC_I2C4_SLAVE
If those defines are not set, default value is 100000
for speed, and 0 for slave.
completely disabled. Anybody can change or delete
these parameters.
- Alternatively, if you #define _both_ CONFIG_ETHADDR
- _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
+ Alternatively, if you define _both_ an ethaddr in the
+ default env _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
Ethernet address is installed in the environment,
which can be changed exactly ONCE by the user. [The
serial# is unaffected by this, i. e. it remains
this is instead controlled by the value of
/config/load-environment.
+- Parallel Flash support:
+ CONFIG_SYS_NO_FLASH
+
+ Traditionally U-boot was run on systems with parallel NOR
+ flash. This option is used to disable support for parallel NOR
+ flash. This option should be defined if the board does not have
+ parallel flash.
+
+ If this option is not defined one of the generic flash drivers
+ (e.g. CONFIG_FLASH_CFI_DRIVER or CONFIG_ST_SMI) must be
+ selected or the board must provide an implementation of the
+ flash API (see include/flash.h).
+
- DataFlash Support:
CONFIG_HAS_DATAFLASH
Define this option to include a destructive SPI flash
test ('sf test').
- CONFIG_SPI_FLASH_BAR Ban/Extended Addr Reg
-
- Define this option to use the Bank addr/Extended addr
- support on SPI flashes which has size > 16Mbytes.
-
CONFIG_SF_DUAL_FLASH Dual flash memories
Define this option to use dual flash support where two flash
memories can be connected with a given cs line.
Currently Xilinx Zynq qspi supports these type of connections.
- CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
- enable the W#/Vpp signal to disable writing to the status
- register on ST MICRON flashes like the N25Q128.
- The status register write enable/disable bit, combined with
- the W#/VPP signal provides hardware data protection for the
- device as follows: When the enable/disable bit is set to 1,
- and the W#/VPP signal is driven LOW, the status register
- nonvolatile bits become read-only and the WRITE STATUS REGISTER
- operation will not execute. The only way to exit this
- hardware-protected mode is to drive W#/VPP HIGH.
-
- SystemACE Support:
CONFIG_SYSTEMACE
example, some LED's) on your board. At the moment,
the following checkpoints are implemented:
-- Detailed boot stage timing
- CONFIG_BOOTSTAGE
- Define this option to get detailed timing of each stage
- of the boot process.
-
- CONFIG_BOOTSTAGE_USER_COUNT
- This is the number of available user bootstage records.
- Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...)
- a new ID will be allocated from this stash. If you exceed
- the limit, recording will stop.
-
- CONFIG_BOOTSTAGE_REPORT
- Define this to print a report before boot, similar to this:
-
- Timer summary in microseconds:
- Mark Elapsed Stage
- 0 0 reset
- 3,575,678 3,575,678 board_init_f start
- 3,575,695 17 arch_cpu_init A9
- 3,575,777 82 arch_cpu_init done
- 3,659,598 83,821 board_init_r start
- 3,910,375 250,777 main_loop
- 29,916,167 26,005,792 bootm_start
- 30,361,327 445,160 start_kernel
-
- CONFIG_CMD_BOOTSTAGE
- Add a 'bootstage' command which supports printing a report
- and un/stashing of bootstage data.
-
- CONFIG_BOOTSTAGE_FDT
- Stash the bootstage information in the FDT. A root 'bootstage'
- node is created with each bootstage id as a child. Each child
- has a 'name' property and either 'mark' containing the
- mark time in microsecond, or 'accum' containing the
- accumulated time for that bootstage id in microseconds.
- For example:
-
- bootstage {
- 154 {
- name = "board_init_f";
- mark = <3575678>;
- };
- 170 {
- name = "lcd";
- accum = <33482>;
- };
- };
-
- Code in the Linux kernel can find this in /proc/devicetree.
Legacy uImage format:
65 net/eth.c Ethernet found.
-80 common/cmd_net.c usage wrong
- 80 common/cmd_net.c before calling NetLoop()
- -81 common/cmd_net.c some error in NetLoop() occurred
- 81 common/cmd_net.c NetLoop() back without error
+ 80 common/cmd_net.c before calling net_loop()
+ -81 common/cmd_net.c some error in net_loop() occurred
+ 81 common/cmd_net.c net_loop() back without error
-82 common/cmd_net.c size == 0 (File with size 0 loaded)
82 common/cmd_net.c trying automatic boot
83 common/cmd_net.c running "source" command
without a fastmap.
default: 0
+ CONFIG_MTD_UBI_FM_DEBUG
+ Enable UBI fastmap debug
+ default: 0
+
- UBIFS support
CONFIG_CMD_UBIFS
CONFIG_SPL_STACK
Adress of the start of the stack SPL will use
+ CONFIG_SPL_PANIC_ON_RAW_IMAGE
+ When defined, SPL will panic() if the image it has
+ loaded does not have a signature.
+ Defining this is useful when code which loads images
+ in SPL cannot guarantee that absolutely all read errors
+ will be caught.
+ An example is the LPC32XX MLC NAND driver, which will
+ consider that a completely unreadable NAND block is bad,
+ and thus should be skipped silently.
+
CONFIG_SPL_RELOC_STACK
Adress of the start of the stack SPL will use after
relocation. If unspecified, this is equal to
list, simply add an entry for the same variable name to the
".flags" variable.
+ If CONFIG_REGEX is defined, the variable_name above is evaluated as a
+ regular expression. This allows multiple variables to define the same
+ flags without explicitly listing them for each variable.
+
- CONFIG_ENV_ACCESS_IGNORE_FORCE
If defined, don't allow the -f switch to env set override variable
access flags.
- CONFIG_FSL_DDR_SYNC_REFRESH
Enable sync of refresh for multiple controllers.
+- CONFIG_FSL_DDR_BIST
+ Enable built-in memory test for Freescale DDR controllers.
+
- CONFIG_SYS_83XX_DDR_USES_CS0
Only for 83xx systems. If specified, then DDR should
be configured using CS0 and CS1 instead of CS2 and CS3.
normal addressable memory via the LBC. CONFIG_SYS_LS_MC_FW_ADDR is the
virtual address in NOR flash.
+Freescale Layerscape Debug Server Support:
+-------------------------------------------
+The Freescale Layerscape Debug Server Support supports the loading of
+"Debug Server firmware" and triggering SP boot-rom.
+This firmware often needs to be loaded during U-Boot booting.
+
+- CONFIG_FSL_DEBUG_SERVER
+ Enable the Debug Server for Layerscape SoCs.
+
+- CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE
+ Define minimum DDR size required for debug server image
+
+- CONFIG_SYS_MEM_TOP_HIDE_MIN
+ Define minimum DDR size to be hided from top of the DDR memory
+
+Reproducible builds
+-------------------
+
+In order to achieve reproducible builds, timestamps used in the U-Boot build
+process have to be set to a fixed value.
+
+This is done using the SOURCE_DATE_EPOCH environment variable.
+SOURCE_DATE_EPOCH is to be set on the build host's shell, not as a configuration
+option for U-Boot or an environment variable in U-Boot.
+
+SOURCE_DATE_EPOCH should be set to a number of seconds since the epoch, in UTC.
+
Building the Software:
======================
unset, then it will be made silent if the U-Boot console
is silent.
- tftpsrcport - If this is set, the value is used for TFTP's
+ tftpsrcp - If this is set, the value is used for TFTP's
UDP source port.
- tftpdstport - If this is set, the value is used for TFTP's UDP
+ tftpdstp - If this is set, the value is used for TFTP's UDP
destination port instead of the Well Know Port 69.
tftpblocksize - Block size to use for TFTP transfers; if not set,
faster in networks with high packet loss rates or
with unreliable TFTP servers.
+ tftptimeoutcountmax - maximum count of TFTP timeouts (no
+ unit, minimum value = 0). Defines how many timeouts
+ can happen during a single file transfer before that
+ transfer is aborted. The default is 10, and 0 means
+ 'no timeouts allowed'. Increasing this value may help
+ downloads succeed with high packet loss rates, or with
+ unreliable TFTP servers or client hardware.
+
vlan - When set to a value < 4095 the traffic over
Ethernet is encapsulated/received over 802.1q
VLAN tagged frames.
flash or offset in NAND flash.
*Note* - these variables don't have to be defined for all boards, some
-boards currenlty use other variables for these purposes, and some
+boards currently use other variables for these purposes, and some
boards use these variables for other purposes.
Image File Name RAM Address Flash Location
CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the
".callbacks" environment variable in the default or embedded environment.
+If CONFIG_REGEX is defined, the variable_name above is evaluated as a
+regular expression. This allows multiple variables to be connected to
+the same callback without explicitly listing them all out.
+
Command Line Parsing:
=====================
warning is printed.
o If neither SROM nor the environment contain a MAC address, an error
- is raised.
+ is raised. If CONFIG_NET_RANDOM_ETHADDR is defined, then in this case
+ a random, locally-assigned MAC is used.
If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
will be programmed into hardware as part of the initialization process. This